Lexus ES 2007-12 :: Random / Multiple Cylinder Misfire Detected - Error Codes On ES350
So on monday the following error codes appeared on my car. What needs to be replaced off the error codes?
P0300Random/Multiple Cylinder Misfire Detected2014-02-04 13:48:29
P0301Cylinder 1 Misfire Detected2014-02-04 13:48:29
P2030No Description Available2014-02-04 13:48:29
P3030No Description Available2014-02-04 13:48:29
C0033No Description Available2014-02-04 13:48:29
P0603Internal Control Module Keep Alive Memory (KAM) Error2014-02-04 13:48:29
C1400No Description Available2014-02-04 13:48:29
Golf IV R32 :: CEL Start To Blink Then Stay On - Random / Multiple Cylinder Misfire Detected
I was driving the car normal with no problem. Got to a red light stop an as I was coming out of the red light the car started to hesitate a bit. So I start to drive home as I was driving home my check engine start to blink and then it stay on. When I got home and park the car I shut off ,then start it up again then the check engine light was off but the hesitation was still there. Then I got my computer and got the vagcom and got this code :
16684-random/multiple cylinder misfire detected
P0300-008- implausible signal
Passat (B5) :: Random / Multiple Cylinder Misfire Detected
What is going on with my sisters passat 2002 V6 GLX Auto 4Motion. Here is the codes:
16730-Camshaft Position Sensor (G163) Implausible Signal
P0346-35-00
16684-Random/Multiple Cylinder Misfire Detected
P0300-35-00
16688-Cylinder 4: Misfire Detected
P0304-35-00
16690- Cylinder 6: Misfire Detected
P0306-35-00
16689-Cylinder 5: Misfire Detected
P0305-35-00
I changed Both sensors and it still same problem. Car only has 40,000 miles didnt change timing belt.
Passat (B6) :: Random / Multiple Cylinder Misfire Detected?
my car was running fine yesterday. Today the check engine light came on and it started to run funny.. I checked the diagnostic code and it says the the cylinder is misfiring and that oxsygun sensor is malfunctioning. (Random/Multiple Cylinder Misfire Detected)
View 4 RepliesAccent MC (2006-11) :: Random / Multiple Cylinder Misfire Detected
I guess misfires are a rite of passage for these vehicles. I purchased it only a week ago. Welcome to Hyundai...
The car has 53k kms. It's throwing P0300 and P030X on all cylinders. There was one instance of P0128. The engine runs smoothly and doesn't seem to down on power, although I have nothing to compare it to. The only performance issue is that it acts as if there is a rev limiter at 6k rpm. It sputters and stops pulling above 6k. Strangely, it doesn't throw the codes under load. The light flashes while it's running steady-state.
I pulled the plugs and they appeared to be in excellent condition with no erosion of the electrodes. The ash is slightly more white than I would expect, making me wonder about it being excessively lean. I called the dealer. They told me that coils are problematic. Replacing the coils made no difference.
That lead me here. I found the thread "Check engine light flashes then stays solid," which referenced the ECM update.
Interestingly, of the codes mentioned on the TSB, the car is having all but the last two.
- P0300: Random/Multiple Cylinder Misfire Detected.
- P0301: Cylinder 1 - Misfire Detected.
- P0302: Cylinder 2 - Misfire Detected.
- P0303: Cylinder 3 - Misfire Detected.
- P0304: Cylinder 4 - Misfire Detected.
- P0128: Coolant Thermostat (Coolant Temperature Below Thermostat Regulating Temperature).
- P0328: Knock Sensor 1 Circuit High Input.
- P0461: Fuel Level Sensor A Circuit Range/Performance.
Tiguan :: 2010 - Random / Multiple Cylinder Misfire Detected - MIL On
My buddy has a 2010 tiguan and hes having a misfire issue. It has a hesitation and the interior lights seem to dim with the hesitation. Heres the codes that pulled up with vagcom.
4 Faults Found:
000768 - Random/Multiple Cylinder Misfire Detected
P0300 - 000 - - MIL ON
Freeze Frame:
Fault Status: 11100000
Fault Priority: 0
Fault Frequency: 1
Reset counter: 255
Mileage: 148426 km
[Code] ....
What it might be?
Ford F-150 (2004-2008) :: Multiple Codes - Random Misfire Detected
I have a 2005 F-150 W/ 5.4 triton, and am having multiple codes. They are:
P0172- System to rich(Bank 1),
P0174- System to lean(Bank 2),
P0300- Random misfire,
P0303- Cylinder # 3 misfire detected,
P0304- Cylinder #4 msfire detected.
Buick - Lacrosse :: Oil Pressure Low Light Came On - Random / Multiple Cylinder Misfire Detected
2008 Buick Lacrosse CXL .. My son said the Oil pressure low light came on when he tried to start the car. It didn't want to start.
When I got there two hours later, it started but had a check engine light. But no low oil pressure light. Sounded like it was missing.
Code from computer came back P0300 "Random/Multiple Cylinder Misfire Detected". I cleared the code. Revved the engine to about 2000 RPM's and the CEL came back on.
Same code. When idling it feels like it's missing. The plugs look good, I am going to replace the ICM.
Passat (B5) :: Error Code 16684 And 16686 - Random / Multiple Cylinder Misfire
I was driving along and the engine started missing really bad. The whole car was bouncing around. At first I thought I had a flat, but when I stopped I noticed it was the engine. I checked the error codes and got 16684 and 16686 --- Random/Multiple Cylinder Misfire.
I had a problem recently with the vacuum hose broken and was causing an error code. Replace the hoses and it has been fine. Checked to make sure that the hoses were secure and they are fine. Doesn't seem to me to be related. So many problems for a car with 57,500 miles
Jeep - Liberty :: Idling Rough With No Error Codes - Multiple Cylinder Misfire
ODB2 Code: P0300 - Multiple Miss-fire
I have an issue with my Jeep Liberty. It started idling rough with no error codes. about a week later it through the Multiple misfire code. I started by replacing the spark plugs. The old ones were from 20K miles ago and still looked good. Replaced them anyway. I still had the code. I put K44 fuel injector cleaner into the tank and drove it home (2 miles.) The next morning I started it and went in side because I had forgotten something. I came out to extremely thick black smoke. It went away after about 2 minutes, the computer code cleared, and the engine idled perfectly. About 2000 miles later the car is once again idling poorly. I added K44 again and for that tank of gas it ran fine, no code. Once new gas was added it threw the same error code and idles very roughly.
So here are some basic info pieces:
1. 8 tanks of gas from 8 different locations.
2. Adding K44 has shown a direct improvement both times, but more significant the 1st time.
3. New spark plugs
4. New coil packs
5. 2005 Jeep Liberty - 3.7L V6 at 99,872 miles
6. Hopefully unrelated is that the car has a small radiator fluid leak I haven't found. It requires 1/2 gallon every 2K miles or so.
There is no knocking sound, it just sounds like there isn't enough gas. Car responds fine to accelerator. Above 10mph car seems to drive smoothly.
Golf IV / Jetta IV :: VR6 - Random Multiple / Cylinder Misfire
Replaced my water pump March 2nd using the "From Below" method. Started the car after and the check engine light was on and water pump was no longer leaking. I drove the GTI to Advance (15 Mins away) it drove fine and I pulled two codes.
P0300 - Random Multiple/Cylinder Misfire
P0301 - Cylinder 1 Misfire
The car pulled and drove normally. The next day the car is misfiring badly. Hesitation and bucks when accelerating until roughly 3k then smooths out.
I will swap my coilpacks and check if the misfire moves as soon as I can get my hands on an OBD2 Scan Tool.
From what I understand about the VR6 :
-The water pump runs off the serpentine belt
-Camshaft timing is controlled by the timing chain.
-Timing chain is not affected by the serpentine belt/pulleys.
Questions :
-Can turning the Crankshaft Pulley affect timing?
-Can that be the cause of the misfire?
24V VR6
Golf IV / Jetta IV :: 1995 - Random Multiple Cylinder Misfire?
I have a 1999.5 Jetta VR6 12v, last week the car would not start. After some tests I determined the coil pack had gone bad. Replaced the Coil with a brand New aftermarket German made coil. Now 1 week later, driving at highway speed CEL came on, started to flash and obviously misfiring again. Ran Codes and now im getting these DTC's:
1)random multiple cylinder misfire detected p0300
2) cylinder 4 misfire detected p0304
3) ignition coil output 3 electric malfunction p1395
4) cylinder 3 misfire detected p0303
has this new coil gone bad already after a week?
New issue?
Plugs were replaced less than a year ago, wires were apparently replaced by previous owner about 2 years ago now. Crank sensor replaced less than a week ago...
Passat (B5) :: 2006 - Random / Multiple Engine Cylinder Misfire
I have a '06 Passat 3.6. I had the intake and valve cover off the other day and when I put it back together it started missing bad. The code it is throwing is a P0300/ random/multiple engine cylinder misfire. What is wrong?
View 2 RepliesGolf IV / Jetta IV :: Codes For Random Misfire And Small EVAP Leak Detected
Okay, so a few weeks ago, my tire blew out on the freeway. Of course my spare wasn't in there and when I got one I couldn't get the lugs loosened. My 4way was too big on all sides. It was late, I am a single mother of two young kids so I had no choice but to drive slowly to get it off the freeway. The next morning I came back fully prepared, got my car in to get a new tire. I have been driving with ONE code for my CEL, but at the shop (where I use to work) I used the scanner and it threw 5 codes.
P0300 Random misfire
P0442 Small EVAP leak detected (this one was already there)
P0420 Catalyst system below threshold bank 1
P0301 Misfire cyl 1
P0303 Misfire cyl 3
My beautiful love is an 02 Jetta 2.0 4 Cyl. Now, since 4 of these codes popped up AFTER my first blowout (I turn 30 next month, knock on wood)
Did driving my car at 5 mph about a mile and a half (everywhere up until the gas station was NO PARKING) do something to my car? All of a sudden, any in town driving ESP IDLING makes my check engine light blink and my car has no power I just have to pull over wherever I am. I checked the car out myself on the side of the road and my cat was glowing. After this I do not drive my car.
So, what should I do. I did a tune up. Should I replace the 02 sensors then the cat?
Prius (Gen 1) :: Auxiliary Battery Drained - Random / Multiple Cylinder Misfires Detected
I left the key on and drained my auxiliary battery(It was weak before) and when I jumped it it started and then shut off after ~20 seconds. I tried various different things and all I succeeded in doing was draining my HV battery from starting it so many times. So I disassembled the pack and recharged it and now it starts and runs but it is misfiring. It throwing 4 codes:
P0300: Random/Multiple Cylinder Misfire Detected
P0302: Cylinder 2 Misfire Detected
P0304: Cylinder 4 Misfire Detected
P1305: Ignition Coil 2 Primary Feedback Circuit
I inspected the igniters and plugs and they seem to be OK and I'm not sure where to look next. I'm not sure if the battery issue is related or not but I did replace the auxiliary battery.
Ford Super Duty (1999-2016) :: 2008 F250 - Random Misfire Detected On Cylinder 7
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
Ford F-150 - 1997-2003 :: Error Codes - Misfire Detected On Cylinders 2 / 5 And 6
My wife and I received her father's 2002 F150 4.2 5 speed 2 wheel drive truck after his passing. He purchased new plug wires and wanted to replace them. So, this weekend I put in new plugs, plug wires, changed the air filter, and changed the oil and filter. Started up and ran really rough. Threw my code reader on after taking it around the block and found the following codes...
P0316 Misfire detected in first 1000 revs,
P0302 Cylinder 2 misfire,
P0305 Cylinder 5 misfire,
P0306 Cylinder 6 misfire.
New plugs were Motorcraft plugs, but had skinnier center compared to the ones that came out of truck.
Where do I start? What do I do? I am really confused as I have changed plugs and wires before and always had vehicle run better or same as before change.
Accent MC (2006-11) :: 2008 - Multiple Cylinder Misfire Codes
We bought the car used for my youngest daughter and it had a couple of codes in it. 1st was the o2 sensor.. easy fix, grabbed an OEM one and stuck it in. Then there was the Cyl 2/ multiple cyl misfire codes that kept getting thrown.
I've seen a bunch of post about people pretty much doing the same things I started out with and still having a problem.....
1) Swapped around all the coils.. still got a #2 misfire... So, coils are good.
2) Swapped in NGK Platinum plugs with a .032 gap.... still getting misfire.
3) Replaced the crank shaft position sensor...... still misfire
4) Noticed that there was an Ebay injector in the #2 cyl...... when I pulled the plugs, that cyl was running a little lean..... bought an OEM injector to go back in there...... still getting misfire
SO, I tried using a propane torch head and putting out gas around the intake to search for vacuum leak and got no response....... so, for the heck of it, I went old school and grabbed a can of starting fluid and started spraying it on the intake around where it bolts to head... bam... found a vacuum leak on #2 cyl....... ordered an intake gasket off of ebay, spent about 3 hours on it pulling the intake and replacing the gasket,( the bolts had loosened up over time and there were small tears in the gasket allowing it to suck air) .. put the new gasket on, cleared the codes and it's been running perfect ever since.
Check for a vacuum leak where the intake manifold bolts to the head... might save time and money.
Lexus SC430 :: P0300 (Random Multiple Misfired Detected) / C1201 (engine Control System Malfunction)
I own a 2002 SC430 with 20,200 miles on it which I purchased new. The other day the check engine light came on. I checked it with the code reader and got the following 2 codes. P0300 (random multiple misfired detected) and C1201 (engine control system malfunction). The car ran great before, now running real ruff and when you drive it has less power.
View 9 Replies