Ford Ranger / B-Series :: 1999 B4000 - Random Stalls / P0171 And P0174 Error Codes Come Up
I have a 1999 B4000 V6 4.0L with 78K miles on it. I recently had P0171 and P0174 error codes come up. I replaced the MAF sensor and have not had the codes return but now the truck will basically stalls out when sitting at a stop light. It does not do it all the time just randomly. It has never done it when engine is cool but only once up to temp. The idle is smooth at cold engine but begins to get rougher once warmed up (nothing too bad just noticeable). I cleaned the IAC with MAF cleaner but no joy. I reseated all plug cables at the coil but no change. RPM around 600-700 then fluctuates up a bit then truck will stall quickly( I usually cannot put other foot on gas in time to get it to increase RPM before it dies)....
View 5 RepliesFord Ranger / B-Series :: 2000 - Stalls At Stop Lights / No Codes
I have a 2000 ford ranger 2.5 automatic. runs fine except when stopping at lights and intersections it stalls. I have changed the MAF, TPS and hasn't made a difference.Truck only has 64,000 miles. What to look at next. no codes...
View 14 RepliesFord Ranger / B-Series :: 2000 - Codes PO500 - Cluster And ABS Module Faults
I am looking for the part number for the ABS speed sensor mounted on the rear differential for my 2000 Ranger XL 4x4 3.0 flex fuel model. I am also looking for the name of the part so I can look it up on the ford parts site. while looking I have found these names ABS speed sensor
Powertrain Control Module Speed Control Sensor
I had my truck in the shop and they did a health check, they found these codes po500 - cluster fault and the abs module fault
Ford Ranger / B-Series :: 1994 - Got Codes 218 And 998?
Working on a friends 94 ranger, 2.3 L with codes 218 and 998. Chiltons manual does not even show this code. Code is for Loss of Ignition Diagnostic Monitor (IDM)/left side. What exactly is this? Can't find anything that explains the IDM.
998 means a hard fault.
Ford Ranger / B-Series :: 2006 - Got Error Code P0171 - Rough Idle?
I have a 2006 Ford Ranger with the 3.0L v6. The check engine light came on and the code it is blowing is a P0171. It runs rough at idle or when I let off the accelerator and "fine" at speed.
The code told me to check/clean the MAF which I have done. Next on the list that I saw was the PCV valve. I disconnected the electrical to it and then disconnected the hose. Some oil poured out of it... not a lot but some... The valve still seems free, it clicks when I rotate/shake it and I can blow through it (I know, highly scientific). I can replace this (if I can find it, Napa and Advanced Auto don't have a part that looks like it...) but I'm wondering what else could be wrong.
Ford Ranger / B-Series :: 2001 - Suddenly Died - No Codes?
My 2001 2.5 manual suddenly died. The starter turns the engine over, but I don't get a) fuel (changed the fuel pump) b) spark c) Engine check light. When I plug the OBDII reader in, it simply says "ERROR". No codes, no other language.
While trying to figure it out this morning, after trying to start it 50 times, it actually fired for a few seconds, but then died again.
I checked relays and fuses and nothing seemed bad. I swapped relays around too.
I unplugged the battery, then the computer, but nothing got it to fire again.
Ford Ranger / B-Series :: 1996 - Codes P1131 And P0401
Originally started with a p0302 code, and it cleared. CEL came back on with codes p1131 and P0401. First time with an 8 plug 4 cylinder. Truck has 263000 miles, and still original (metal) DPFE sensor. 1996 ranger 2.3L.....
View 1 RepliesFord Ranger / B-Series :: Misfire Codes Started Out On Cylinder 5
I am currently chasing misfire codes that started out on cylinder 5 p0305 was the first code I replaced spark plugs and wires about 200 miles the code returned checked coil with meter it was barley in spec. I have replaced coil same code only difference was a hard start cold or hot replaced injectors now hard start is fixed but logging codes for right bank is to rich and p0300 304 305 and 306 also performed compression test on right bank and readings are 155 155 and 160...
View 3 RepliesFord Ranger / B-Series :: 2004 2.3L - Failure To Start But No Codes
My father called me last night to say that his 2004 Ranger, 2.3L engine would not start. He said it cranked over but would not fire. The only other problems this truck has had was a misfire about 6 months ago, which was corrected by a new coil (wires and plugs were changed at that time also).
I looked at it this morning, starting off by cranking it just to see for myself. It cranked fine, stumbled some as if it was trying to fire but never would catch, and I noticed immediately the smell of raw gas from the exhaust pipe. It acted flooded, but injected vehicles are not supposed to flood, so...
No "check engine" light was on, and no codes at all showed on my Actron code scanner. The truck has a half tank of fuel in it, was last filled about a week and a half ago, and was last started about four days ago. It is kept in a garage, currently at about 45 degrees F. It ran fine up until the failure to start last night. I can hear the fuel pump running, and the two plug wires I pulled and checked were firing. I installed the wires back, held the pedal to the floor, cranked it over, and after a few seconds it fired and ran! On the second restart it started a little reluctantly, but multiple times after that it seemed to start fine.
We let it set for an hour or so, went out to try it again, and it would not start again. After I pushed the fuel pedal in just slightly, it fired and ran fine. I repeated this a couple more times while the engine was still cold; no start without touching the pedal, but would start if I cracked the pedal just a little bit. Once started the engine would idle high (1000-1100 rpm or so) for just a few seconds, then idle down as it should when warm.
I'm puzzled by no code, but I'm wondering if the IAC is bad, causing a no-air "flooding" condition if the fuel pedal is not depressed to crack open the throttle plate. That would explain the strong smell of raw gas at first. But, it seems like the IAC is controlling the idle briefly right after the engine starts, but it doesn't seem to be keeping the idle up as long as it should. Would the IAC throw a code if it were not working correctly?
My other suspicion is the TPS, but again without a code I am not sure. My Actron scanner is one of the better models and will read data from the engine; is there a way to check the AIC and TPS function once I do get it running?
Ford Ranger / B-Series :: 1996 2.3L Automatic - Check Engine Light Came On / Error Code Is P0141
My 1996 Ranger runs ok but my check engine has come on. Using a scanner tool, indicates my cat monitor wont go to ready state and my error code is P0141. According to my research it indicates one of my 02 sensors. How to determine if its the one before or after the cat converter? About 6 months ago I had an exhaust leak repaired around my converter so I know I cant return it under warranty . If its the rear sensor , It looks fairly easy to replace but the front sensor looks a bit cramped.
View 6 RepliesFord Ranger / B-Series :: 1997 - O2 Heater Circuit Codes For All 3 Sensors
1997 2wd, 4.0 - As you can guess it runs pretty bad at idle. It has O2 heater circuit codes for all 3 sensors. I'm leaning towards the ECM because the 2 heater wires are both hot with the key on. I unplugged the computer and turned the key on and just one wire is hot. Looks like the ecm is supposed to ground the wire to turn the heater on, but it's going hot instead?
View 14 RepliesFord Ranger / B-Series :: 1999 - Intermittent Misfire On Startup - No Codes
Previously on "This Old Truck": [URL] ....
Mileage now 298,5xx. Done since last report: Oil change and filter. Trans oil change (merconIII, no leaks apparent). Tires. Front brake pads. Clutch safety switch (was interfering with cruise control operation) Coolant replacement. (see below)
Rat damage related overheat (near total coolant loss, but no MIL) at 288k. (Rat suffered acute lead poisoning later that night) No sign of rodents since.
Fuel filter change (after onset of symptoms).
NO MIL/CEL, no pending codes. CEL/MIL operates on KOST.
Temps normal (190F +/-2 deg during steady-state cruise operation, fuel flows and fuel mileage have not changed significantly. (fuel mileage has IMPROVED approx 5%, possibly due to gentler/slower driving)
M5OD with Limited slip 3.73/ payload pkg II (1650lbs)
Symptoms:
- Intermittent misfire on startup, seems to get better as the truck warms up. (intermittent= some days it do, some days it don't.)
- Truck starts and idles well, even with misfire.
- Intermittent loss of power, usually worse on days when no- or minor- misfire at startup/cold idle. From the driver seat it feels like accelerating over painted lines on a rainy day. . . a couple revs of no power, then it pulls hard for a second or two, then misses a couple of shots, lather, rinse, repeat.
- Usually worse in higher gears; (not noticeable in first or 2nd, bad in 3rd at high power settings, now almost constant in 5th, to the point that truck will not accelerate below 3000rpm in 5th even on flat ground.)
- Fuel flows above 4GPH/ OBDII "LOD" (engine load) reported above 75% are typical during malfunction. (Fuel flows have been as high as 9GPH with no problems on other days.)
Symptoms started at approx 292k and have been slowly getting worse over the past few months. . . . usually worse at beginning of trip, fading to very occasional after 50 miles of high-speed driving. Some days/trips no noticeable malfunction.
Thoughts:
1) Ignition wires tired? (did visual inspection, no obvious damage, but no water spray test performed, but seems likely given that the problem is most evident in conditions that would lead to high cylinder pressures.)
2) Fuel pressure? (not measured yet. . . original pump but possibility discounted due to intermittent nature of malfunction.)
3) O2 sensors tired/rat damage? (Original units still installed/ no obvious damage on cursory visual inspection under truck)
4) Injector going bad or injector wiring rat damage?
5) Plugged catalytic converters? (no sound of blown exhaust gaskets, exhaust flows well at tailpipe, with puffs at misfire.)
6) Cam sensor? (never been replaced; known issue with this model engine. Had intermittent mystery squeak that came and went at approx 250k-260k)
7) Clutch slipping? (never had one do that; always lose the throw-out first)
8) LSD problem? (fluid level/ appearance ok, last changed 150k; would expect worse in LOW gears)
9) Blown head gasket/s?
10) Cracked heads/ block? (Oil and coolant levels and appearance normal)
So: That's the plan of attack. What am I missing? (Clutch last done approx 170k; burned throw-out, did disk, flywheel, pressure plate, slave cylinder while the trans was down. I did not open the hydraulics or disturb the pedal linkage when I replaced the safety switch. )
Ford Ranger / B-Series :: 1993 - Getting 157 / 158 And 159 Codes - Mass Air Flow Voltage?
Truck is a 1993 ranger 4.0 ohv
Ok I have been getting 157, 158, and 159 codes. I have cleaned and replaced the MAF with no success. I checked the voltage to the sensor 12v, checked the voltage from the signal wire and it is to high. It has been high on the cleaned unit and on both replacements, so I am thinking it is not the MAF, but what will cause it to register high. I cant get the signal voltage below 1.9V at idle.
Signal also reads high with the ignition on and the engine off. What would cause the voltage to be high, I have read it could be an IAC but I would think that would not effect it with the engine off.
Ford Ranger / B-Series :: 2002 - Rough Idle Codes / Cylinder 2 And 3 Misfiring
I have an 02 ranger xlt 3.0, it started having a rough idle, codes say cylinder #2&3 misfiring, changed plugs, wires, coil pack, didn't work, still same code, checked injectors on right side, all 3 had ohm reading of 15.8-16.5, the injectors were clicking like they are supposed to, sprayed carb cleaner around the intake ports, didn't change the idle at all,what else can I check or do? with out tearing the engine apart, unless of course I have to, the truck has been very good to me, it's got 205,000 miles on it, I need it to last at least another year...
View 4 RepliesFord Ranger / B-Series :: 2003 - Misfiring On Start Up - Got Codes P0316 And P0304?
My 2003 ford ranger 3.0 v6 is having a misfire on start up and it is located in the forth cylinder. Where to start to get rid of this problem. i have already changed all my plugs wires and even the coil pack cleaned out the maf and looked for possible leaks. the car shakes really bad at lights and the check engine light starts to flash. Need diagram of where all the cylinder numbers are at and maybe the firing order?
View 14 RepliesFord Ranger / B-Series :: 2004 - Rough Idle - CEL With P0303 And P0316 Codes?
I love my Ranger. I'm quite impressed with the power and durability. I'm ticked at Ford for stopping production.
I have searched my problem and could not quite narrow it down. I have also tried several remedies with no improvement. I need to narrow it down to a specific item.
2004 Ranger, 4.0 liter, 4x4, 131,000 miles, runs great above idle.
Problem: rough idle, idles at about 750 rpm's. If i raise the rpm's to 850 and up, smooth as silk.
The truck did this a few years back. Not quite as rough and it went away by itself.
Engine light came on this time with P0303 & P0316 codes. I have replaced: plugs, wires, coil pack. I know that the #3 plug is sparking quite well. the #3 injector is getting signal to spray not sure if it is. I have 4 O2 sensors and I believe I tested them correctly (passed). The passenger side upstream or pre cat sensor has not been tested yet. Had to rent a tool and will do that in morning. I slid a piece of aluminum roof flashing between the crank position sensor and the crank pulley. Not a noticeable difference. While at idle (750 rpm's) I pulled each (#3,2,1,) (one at a time) injector wire plugs off the injectors. No noticeable difference. I pulled the vacuum line off the egg and operated it with a vacuum tool. Seems to be working fine. Sprayed carb cleaner around on vac lines. No engine surge
Ford Ranger / B-Series :: 2003 - Lean Codes / Jerking At Highway Speeds
I've got a 2003 Ranger 2.3L DOHC, 5 speed, 2WD. It has a check engine light with codes :
P0316-Engine Misfire Detected On Startup
P0704-Clutch Switch Input Circuit Fault
P2195-O2 Sensor Excess Lean Signal Bank 1-Sensor 1
P0171-System Too Lean (Bank 1)
The truck runs fine when coasting or accelerating but when holding a steady light throttle to maintain speed the truck starts bucking and jerking. It's doesn't feel like a misfire, more like a fuel cut out condition. When this happens and you come to a stop, you can smell that the exhaust is very rich coming out of the tailpipe. I've already replaced the upstream O2 sensor and I did a tune up about 15k ago. I'm thinking fuel pump or fuel pressure regulator. I doubt if this is related, but on start up (more so on a cold start up) the A/C compressor clutch kicks in and out 3-5 times and makes a terrible racket.
Ford Ranger / B-Series :: 2003 - High Idle And Shoot Up Between Shifts / No Codes
My '03 Ranger is having a high idle problem. It's a 3.0, manual, 2wd, 141,000 miles. When it's cold it will idle at about 1500 but once I drive it, even just to the end of the block, it will idle at about 3000 and shoot up towards that between shifts. At a traffic light it will idle at 3000 and maybe go down to about 2500. If I bog it down with the clutch it goes right back up once I put the clutch back in or put it in neutral.
I replaced the IAC, no luck. I cleaned the MAF and checked the voltage on the TPS and it is good. I replaced the PVC valve, but the old one was fine anyway. I've sprayed around with carb cleaner and don't notice any difference. I've plugged it into my dad's AutoTap which lets me monitor everything on my laptop and the only thing I can see that looks suspicious is that even with the engine off, the Absolute Throttle Angle reads 18.8%. If I step on the gas with the engine off it goes up to 91.8% so I would imagine that just has to do with the function of the TPS and probably isn't out of the ordinary, but I don't really know what that number means or what the Absolute Throttle Angle is or is supposed to be.
Short of taking the intake plenum off and physically inspecting it for cracks, I'm stumped.
Ford Ranger / B-Series :: 1993 - Self Test For Reading Codes Via CEL With OBD1 System?
I just tried doing the self test for reading the codes via the check engine light with the OBD1 system on my '93 4.0 Ranger. Problem is: When trying to mark down the flashes of the check engine light, they flash so erratically and rapidly that there is no way to accurately count. At times the light flickers so fast it never even gets to get fully bright enough to tell if it is actually a "flash" or not. I'm (again) trying to diagnose an issue with the truck starting and running fine for about 3-4 minutes and then like flipping a switch begins blubbering and belching out black smoke, check engine light flashes on/off randomly, then the engine will eventually die. It will restart provided the ignition switch is turned all the way off and attempted again, generating same results only within 30 seconds or so. If you try restarting w/o turning the ignition all the way off, it'll spin over but won't start. ECM?
View 4 Replies