Ford Aerostar :: 1997 - Check Engine Light On
78,000 miles on odometer. The van starts and runs great. Always has. No change in performance since check engine light went on. Took it to local parts store here in California. They used to run codes here but can't any longer for the usual reasons. I replaced the EGR valve because I knew it was due and disconnected the battery and started the van. Light was off. Drove it a few times and it came back on again. Still runs fine though. I heard the Aerostar may kick a code off simply because it's due for a plug change. I think the plugs are original so I'm going to replace them. Plug wires too.
View 14 RepliesFord - Taurus :: 2001 - Engine Light Flashing With Car Shaking And Dying When Idles
I have 104k miles on car, had tune up back in 09, new die hard battery from sears spring '10, just today my car started to shake when in idling, check engine light flashing. It seems to shake itself even while driving, when in idle it will then kill or die. Had radiator flushed January 2nd, 2011 due to heat not pumping through, still doesn't work (I know heater core) like it should. Finally the other problem is when I start & turn the car on it won't turn over-it wants to but takes a few tries like turning key each click like as if it were alternator, does sound like it would if it did turnover but like I said it takes a while & maybe will fire/catch. What the heck is going on? 2001 flex fuel as well but I only once put it in.
View 10 RepliesFord - Explorer :: 1999 - Misfiring / Shaking / Rough Idle - Engine Light Flashing
My 99 Explorer XLT V6 SOHC has been misfiring lately. In idle the RPM needle fluctuates a bit and the vehicle vibrates and shakes. At night when the lights are on I notice them dim a bit as the engine struggles in idle. It doesnt stall very often at all. Accelerating I notice way less power and the engine studders. Thats when the engine light comes on flashing. Then remains on solid afterwards.
I brought it to a mechanic friend who read the code and it was cylinder two misfire as well as O2 censor. I replaced the plugs and leads and censor. Noticed the plug in cylinder two had little to no gapping. Thought I had fixed the problem. Vehicle ran perfect. Three or four days later driving on the hwy same problem came back. Thinking it must be the coil pack I got one for a good price and replaced it.
Again, the truck ran great for four days and now the problem has returned. Same thing, shaking studdering and flashing engine light. I have verified the locations of the wires and plugs a few times so i believe they are all properly installed.
Ford Aerostar :: 2002 - Spit And Sputter And Check Engine Light Start Blinking
My 2002 Windstar SEL has been giving me a fit and I`m not getting any codes as to why. Here`s the 2 main issues. Clicking when i go to start up in a.m. if it`s below 50 degrees. ( Battery has been checked and all is o.k. or so I was informed). As long as it`s warm it starts fine every time. Also,it seems like the least bit of wet on the underside will cause it to spit and sputter and the check engine light will start blinking until it sits and dries for a while. (A very shallow puddle less than 6 inches deep at low speed or even the automatic car wash that sprays the undercarriage).
View 2 RepliesFord Transmission :: Check Engine Light On / OD Light Flashing Sometimes - Code P1747
I have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 RepliesFord F-150 - 1997-2003 :: 2000 - Check Engine Light Came On / Truck Started Shaking
I have a 2000 f150 4x2 5.4 168k... Check engine came on,started shaking, weather was really cold. RPM would be a little high then low then back up. Especially when I turned on heater. Felt like truck would die but never does nor does it have issue starting.
So far, I have replaced two oxygen sensors inside engine,all coils, spark plugs, fuel filter, had injectors cleaned, intake cleaned. Truck runs better but, light came on a day later again. I can feel the tiniest of shaking going on and, cold mornings still make RPMS a little unstable. I was driving truck on highway at about 60 mph when a slight tug was felt and Truck check engine came on. I feel truck heavy, once it warms up completely, a little lighter.
Codes came up at auto zone as P1151
But I'm running out of options and frankly, money to fix this truck.
Checked the MAF and looked okay.
I'm with minimal skills.
Ford - Fusion :: 2012 - Check Engine Light Came On Steady Not Flashing
I have a 2012 Ford Fusion SEL. In late December, the check engine light came on (steady, not flashing). I took it to a local mechanic, as the nearest Ford dealership is a 45-minute drive away. He said an evap code came up indicating that there was a problem with the vent valve solenoid, not the capless fuel filler. However, he did not have the diagnostics to research it further.
As there have been problems with the vent valve solenoid, including a recall (for which we do not qualify), my husband bought and installed the part on Jan. 7. We both drove it several times since then, and the check engine light stayed off. But when I drove it today (Jan. 11), the light was back on.
Passat (B5) :: 2004 VW Shaking - Check Engine Light Came On
I am still pretty new to the VW world. About 2 months ago I bought an 04 GLX 4Motion Passat with a 2.8 V6. On Saturday night my fiance (and primary driver of the VW) went to go start the car to go out for the night and the check engine light came on and she said the car was kind of shaking. She decided to take my car instead. I went out yesterday and today to try to start it and it wont crank over; it sounds like it wants to but just wont. She also said that on Sat. night that it smelled like gasoline outside of the car. What this could be? I dont know if the engine is flooded or what the hell is going on. The car has 93,xxx miles on it.
View 2 RepliesFord - Taurus :: Check Engine Light Keep Flashing - Code PO302 Cylinder 2 Misfiring
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 RepliesFord - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesFord F-150 - 1997-2003 :: Check Engine Light Started Flashing / Running Rough Then Went Off
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesFord Ranger / B-Series :: Rough Idle - Check Engine Light Starts Flashing
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
Ford Aerostar :: 1996 - Airbag Light Comes On - Code 41 Flashing
Got an air bag code 41. Comes on and flashes the code a number of times, then goes off for the rest of the ride. It is a 96 Arerostar, XLT, 4LV6. From what I read it is a short someplace. Where are the crash sensors and how do you check them for "shorts"? I don't understand much about the whole system.
View 12 RepliesChevrolet - Silverado :: Shaking While In Idle / Check Engine Light Came On
I just bought this used truck, 2005 Chevrolet Silverado 1500 extended cab. I noticed some shaking while in idle when I got it back home. The check engine light came on a day or two later, and I recently had a diagnostic test ran on it at the local AutoZone. It came up that I had a P0135 o2 sensor (bank 1 sensor 1) malfunction and a P0101 Mass Air Flow Sensor signal performance issue. The check engine light comes and goes. I stopped by Walmart for about 10 or 15 minutes and when I got back into the truck, the issues reoccurred. For about a minute, the check engine light actually started blinking! And then went away and started running normal again. Its upper confusing. I bought some MAF cleaner to use on it tomorrow and figured that wouldn't definitely clear up my issues, but I'm still wondering if the MAF sensor is enough to warrant the CEL to blink like that?!
View 6 RepliesFord F-150 (2004-2008) :: 2006 - Check Engine Light Started Flashing As Accelerated Uphill
2006 F150 Triton 5.4 Motor... It's been over a months journey with fixing this truck....
How it started: had an oil change, a while back, on long drive after, check engine light started flashing as I accelerated up hill so I pulled over and in a while it was ok, but couldn't get on the gas too much, or it would cause that flashy light thing.
So fast forward to now, after driving it with an intermittent miss for a while, was driving it to work and the miss became a shudder, and she stopped going over 30-40, and runs extremely rough.
Steady but loud idle.
Replaced all plugs with motocraft plugs and new coils all around. No change.
Finally hooked it up to a computer and got random misfires, now it's saying
P0174 bank 2 too lean,
But it's bank ONE that's the only side misfiring.
Here are the freeze frame details:
Frame 1 Mod $00
MIL Status Off
Troub Code P0174
Abslt TPS 24.3%
Eng speed 1665
Baro PRS 71 kpa
Calc Load 100%
[Code].....
Ford F-150 (2004-2008) :: Stumbling / Running Rough - Check Engine Light Is Either On Steady Or Flashing
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 RepliesFord F-150 (2004-2008) :: Check Engine Light Flashing - Running Rough With Tapping Noise
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
Subaru - B9-tribeca :: Check Engine And ABS Light Came On Along With Cruise Light Flashing
I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
Subaru - Legacy :: Check Engine Light Turning On And Cruise Control Light Flashing
Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 Replies