Ford F-150 (2004-2008) :: Stumbling / Running Rough - Check Engine Light Is Either On Steady Or Flashing
Got an 07 Screw with only 50,000 miles. Yesterday, wife drove it home from work and said it would only do 45mph and didn't sound good. No warning lights were on, she said. I test drove it in the evening and it ran totally fine. Today, she drives it to work and said it ran real rough and "Check Engine" light was on. I picked it up from her work and it idles very rough and slow, and once you hit about 2000 rpm, it runs decent, maybe even normal. Below that, it stumbles and engine doesn't sound right. "Check Engine" light is either ON steady, or flashing. I don't have a code reader, so its likely going to the Ford Dealer Monday. Is there any way to read the code without a reader?
View 11 RepliesSonata NF (2006-10) :: Steady And Flashing Engine Light / Car Runs Very Rough
I have a 2006 Sonata 6-cyl with 124K miles on it that also has an engine light that stays on but the car runs fine with the solid light. Only on a COLD start, usually first thing in the morning, is when the engine light starts to flash and the car runs very rough. When the engine light flashes and the car is shut off for about 5 seconds and immediately restarted,the engine light again stays solid and the car runs fine. I have had this issue for approx 2 years.
One mechanic says the code that always comes up is "P0306" (cyl 6 misfire) when the engine light stays on solid. When the light flashes and the computer is read,it gives EIGHT separate codes and all are cylinder misfires (P0300-multiple misfires and then P0301 thru P0306 for each cylinder misfire).
One dealer in the Phoenix,AZ area says my #6 cylinder valve is sticking and I need a full valve job because they supposedly did a compression test on all cylinders (which I doubt they did). I have spent upwards of $2000.00 already at both the dealer and 2 other mechanics to try and find the issue. I feel it is an electrical problem (sensor or computer itself) because one would think the car should run rough ALL the time if it was the actual valve sticking,but it runs fine when the engine light stays solid. I am running out of time because my emission test is due in 4 months. I do not trust this dealer to diagnose this issue; they have proven to me they are incompetent and just want me to pay through the nose for possible fixes until they finally just happen to stumble upon the correct problem.
Accent MC (2006-11) :: Check Engine Light Steady On
This morning started to drive to work and the check engine light came on or actually did not go off. Not sure which. Anyway it is a steady light not blinking and the car runs fine. Problem is that the warranty is out by about 3 weeks, not by mileage and I have an appointment at the dealer on Monday. If I take it to Partsource and have the code read will it delete the code or turn off the light. Just wondering as I don't want to spend money at the dealer if whatever is wrong is not covered under the emissions warranty if I can get the code and fix it myself. Don't want the code deleted either if the dealer needs it.
View 2 RepliesPhaeton :: Check Engine Light Blink A Couple Of Times And Then Steady On?
Today I got the engine light blink a couple of times and then steady on. Parked the car, waited a few minutes, start again just the engine light on (not blinking anymore).
I scanned the car and got this
VCDS-Lite Version: Release 1.2
Tuesday, 06 August 2013, 13:48:09:11637
Chassis Type: 3D - B5 VW Phaeton
Scan: 01,02,03,05,06,07,08,09,11,15,16,17,18,19,23,27,34 ,35,36,37,38,42,46,48,49,52,55,56,57,61,62,65,68,6 9,72,76,77
-------------------------------------------------------------------------------
Address 01: Engine Labels: None
Controller: 07C 906 018 C
[Code] .....
I have a hard time believing that all coil packs went bad. My wife told me that when she was driving the car she could hear a clicking noise coming from the trunk so I think this could the fuel pump not giving enough fuel but I was hoping to get an error for it.
Ford - Fusion :: Check Fuel Inlet Light Went On
The check fuel inlet light went on. Should we be concerned? What does this mean?
View 9 RepliesRodeo :: 99 Honda Passport - Check Engine Light Popped On And Off For Awhile And Now Steady
I have a 99 honda passport, runs like a dream. Let me say it also IDLES perfectly.
I usually get about 300 miles to the tank, but now my miliage has dropped significantly. The check engine popped on and off for awhile and now its on steady. The computer reads the error of "Insufficient EGR Flow". My mileage has dropped down to about 240-250.
I've already put a brand new EGR Valve in it. That's the only code the computer reads.
I know my mechanic cleaned out the valve part itself I don't' know if he did anything other then that.
When he put the new valve on the car ran without the check engine light for a day then came back, and if I am not mistaken my gas mileage was back to normal, but since the check engine light has come back on the mileage has dropped back down again.
Volvo :: Check Engine Light Blink But Never Got Steady / Fuel Pressure Error Code
I had a Check Engine Light a couple months ago, and I took the car to the garage to have it checked out. They told me they got a Fuel Pressure Sensor malfunction code, and that the sensor had to be replaced. I did so myself, an it is ridiculously easy, and the car worked fine. I noticed the Check Engine Light blinked a couple of times while I was driving, but never got steady. A couple of days ago, it did. Out of a bad gut-feeling, I purchased a ODBII scanner, and I scanned the car myself. I got the same error code as the garage did, but the sensor should be fine.
View 5 RepliesElantra MD (2010-15) :: Check Engine Light Steady Not Blinking - Codes P2096 And P2196
I have a 2011 Elantra that I purchased brand new. Has over 60,000 miles on it. Had a check engine light come about year or so ago which was fixed with a software update at the dealer.
Check engine light is back on now. Steady light; it's not blinking. Brought it to my mechanic. Ran diagnostic and said the oxygen sensor needed to be replaced. P codes were P2096 and P2196. He ordered the sensor from the dealership and installed it. Reset my cars computer. I drove the car 26 miles and the engine light came on again.
Here are my questions:
1. Wouldn't my mechanic's diagnostic equipment tell him what the problem or all the problems were? Why would it tell him the oxygen sensor needed to be replaced when there seems to be another problem causing the engine light to come on?
2. Would the dealership have more insight into a check engine light system problem than a mechanic shop may have?
Ford Transmission :: Check Engine Light On / OD Light Flashing Sometimes - Code P1747
I have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 RepliesFord - Aerostar :: Check Engine Light Flashing / Acceleration Creates Shaking
My mechanic said one cylinder isnt working though we havent done any checking beyond wires. It's not worth putting money into but I cannot afford to get anything else. Will driving on just the 5 cylinders create increased damage or other issues that will get me stranded? it starts right up, is rough but levels out after a couple minutes It is smooth driving under 40mph, but acceleration above that creates shaking and check engine light flashing, no ominous ticking noises but can tell not firing on all cylinders. Problem is I will have to drive it highway speeds at some point-tried it before and made it-was able to eventually baby it up to the required traffic mph with the shaking diminishing and smoothing out but rattling started up again every time I had to hit the accelerator to increase the speed. What can I expect by continuing to drive it?
View 8 RepliesSonata I45 (YF - 2011+) :: TPMS Warning Light Started Flashing Then Came On Steady
Today I drove about 250 miles, round trip. About 75 miles from home, my TPMS warning light started flashing, then came on steady. I also received the Blue Link message about problems with the TPMS system. We pulled off the interstate at the next service station (about 3 miles) and checked all of the tires. All 4 read exactly 33 psi.
Restarted the car and continued on. After about a mile, the light turned off. About 10 miles later, the light started flashing again. It flashed for about 2 minutes then shut off again. We continued home without seeing anything more from the light.
The only thing at all out of the ordinary, is that the temperature has changed from a high of 35F earlier in the week to 70F today. There is a lot of moisture on the ground. Is it possible condensation may have affected a sensor? I have a 2013 GLS with 2800 miles on it.
Ford - Taurus :: Check Engine Light Keep Flashing - Code PO302 Cylinder 2 Misfiring
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 RepliesFord - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesFord F-150 - 1997-2003 :: Check Engine Light Started Flashing / Running Rough Then Went Off
Ok on the way the my 1997 f150 4.6 L 180,000 check engine light started flashing and running rough and then the light went off, Also we took the Aftermarket Dynomax muffler off of it earlier today if that makes any difference, it still has the Cat Converter, New Plugs and Napa Wires.....
View 12 RepliesFord Ranger / B-Series :: Rough Idle - Check Engine Light Starts Flashing
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.
Ford F-150 (2004-2008) :: 2006 - Check Engine Light Started Flashing As Accelerated Uphill
2006 F150 Triton 5.4 Motor... It's been over a months journey with fixing this truck....
How it started: had an oil change, a while back, on long drive after, check engine light started flashing as I accelerated up hill so I pulled over and in a while it was ok, but couldn't get on the gas too much, or it would cause that flashy light thing.
So fast forward to now, after driving it with an intermittent miss for a while, was driving it to work and the miss became a shudder, and she stopped going over 30-40, and runs extremely rough.
Steady but loud idle.
Replaced all plugs with motocraft plugs and new coils all around. No change.
Finally hooked it up to a computer and got random misfires, now it's saying
P0174 bank 2 too lean,
But it's bank ONE that's the only side misfiring.
Here are the freeze frame details:
Frame 1 Mod $00
MIL Status Off
Troub Code P0174
Abslt TPS 24.3%
Eng speed 1665
Baro PRS 71 kpa
Calc Load 100%
[Code].....
Ford F-150 (2004-2008) :: Check Engine Light Flashing - Running Rough With Tapping Noise
2005 F-150 4.6L 2WD, 268,000 miles....
Recently I got a flashing 'Check Engine' light and a rough running engine (along with a tapping noise) when I was passing someone (and pulling a trailer). I retrieved codes 300, 304, & 305. I can't swear to it, but I think the tapping noise started at the same time as the coil problem.
I replaced coils #4 & #5 (later that same day) and the engine smoothed back out but the tapping noise is still hanging around. The noise speeds up at higher RPM's and doesn't go away if I shift into neutral. Oil level and pressure are fine and I only use Motorcraft 5W-20 and Motorcraft filters (and change the oil every 5K miles).
Not sure if this is relevant: I think I have bad valve guide seals (blue smoke after long idles) but no other problems that I am aware of. It sort of sounds like a lifter, but is there a good way to pin it down? Is it possible that this tapping is related to the bad coils?
Subaru - B9-tribeca :: Check Engine And ABS Light Came On Along With Cruise Light Flashing
I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
Subaru - Legacy :: Check Engine Light Turning On And Cruise Control Light Flashing
Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 Replies