Ford Super Duty (1999-2016) :: F250 Goes Into Limp Mode / OD Light Flashing / Code P1747
F250 7.3L diesel started to flash OD light, goes into limp mode, code p1747. No other codes. Have had issues for a couple of years where the truck would not shift into gear for awhile; sometimes a couple of minutes till it would engage. Have done lots of diagnostics. Visual check harness. Have 12v on pins 1&12 on harness at transmission plug. Plug had some ATF visible, but cleaned it up and continuity good. (with 4" exhaust hard to get to connector).
Checked all solenoid wires with a DVM back to plug at PCM for continuity and shorts, all good. Pulled transmission pack and checked resistance on all solenoids except temp varistor all within specs. Removed Banks Trans Command and rewired tranny plug and pulled Ottomind chip from PCM. Still goes into limp mode and throws code. Did not see any bad solder joints or burns inside PCM by the way.
Seems like PCM right? But here is a complication to my issues. For over a year I have been having electrical issues like the radio not working and windows not working intermittently after starting up. After running for awhile or on restart would work fine. Sounds like the Instrument Cluster issues or relays.(?)
Will be pulling IC and checking for any bad solder joints. However, did not throw p1747 till just recently and now my radio has really gone wonky. It comes on when key is on automatically and then proceeds to cycle through settings; AM-FM-CD.
So questions are, "Is it possible that a bad Instrument Cluster can cause a p1747 code?" "Bad Ground to Tranny" "Can a bad PCM cause a electrical issue in IC??" "Are these 2 separate issues?"
2002 f250 7.3L, 4R100 automatic trans, ~180,000miles
Banks Stinger package, 4" exhaust, TransCommand, (now removed).
Ford - Taurus :: Check Engine Light Keep Flashing - Code PO302 Cylinder 2 Misfiring
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 RepliesFord - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesSonata NF (2006-10) :: Random Misfire Code P0300 - Check Engine Light Flashing
I know it is a random cylinder misfire code however I started my car in the morning and it was fine I moved it and put it back in my driveway. I started it up later and waited for it to heat up i came back outside 10 min later and my check engine light was flashing and my car was shaking like crazy you could tell the engine was misfiring like crazy. I had under a quarter of a tank but not empty yet. I shut it off and turned it back on and it was still doing it. I drove the mile to the gas station the way it was.
Under partial throttle it was revving to 4500 and over 5, had to let of throttle to make the car shift up a gear. I filled up and started the car again performed fine after that however the check engine light was solid now and still on. I went to my local mechanic and he read that code P0300. I changed my spark plugs that day and they were crap the original spark plugs I have 65,xxx on my car now. Car is smooth now. I cleared check engine when i saw him first and it did not come back on all day even before i changed the spark plugs later that night. Why my light was flashing and why my car was acting like that till i filled up?
Intrepid :: Check Engine Light Came On - Transmission Code P0731
My wifes 1998 Intrepids' Check Engine Light came on yesterday, and while she was turning into the driveway the car stalled. It would fire right up again, and drive normally, but when she went to pull into the driveway again it stalled.
I took it into the shop, and they read the computer and thats when the P0731 code showed up.
P0731 Incorrect gear ratio # 1
When I went to bring it home, I then noticed that the speedometer was not working, and the tranny wasn't shifting out of 1st gear. The tranny fluid is clean and not burnt.
Ford - Mountaineer :: 2003 V6 - Check Transmission - OD Light Constantly Flashing
I have a 2003 mountaineer v-6 awd drives pretty good but od light is always flashing even if ignition switch is open and truck not started..and check transmission on message display also..the only thing that i feel its really tight on turns as if it wants to lock up but once steering gets straight it runs fine... I know that a regular scanner cant pull codes I got to go to transmission shop but chances are there gonna tell me its trans time....
View 6 RepliesCamry :: 2002 V6 Automatic Transmission - Check Engine Light Came On With Code P0770
I have a 2002 Toyota Camry V6. The warranty expired in Feb 2007. The car has only 67,000km.
The check engine light came on and the code is P0770, Solenoid E malfunction. The problem was first reported at 43,000km, when the car was still under warranty but only a transmission flush was performed and the code was reset.
I wrote Toyota and after almost two months they told me they do not cover it because is out of warranty and I do not qualify for the Goodwill program. I tried again to tell them that instead of fixing the root of the problem they temporarily covered it, but again I got a NO. No comments about the mileage, time, etc. Just the car is out of warranty and I'm out of luck.
Ford - Explorer :: 2002 V8 - OD Light Flashing And Message Center Says Check Transmission?
Wife's truck- 2002 v8 limited explorer with 116k... Yesterday she calls and says the od light is flashing and the message center says check transmission. She drove it home then when I got home the light was off and all seemed ok. I am taking it to have the codes read and hoping that my mechanics scanner picks up a code.
View 2 RepliesSonata I45 (YF - 2011+) :: Engine Check Light Code, P0711 / Transmission Shift Occasionally
I own a 2013 Hyundai Sonata. Two months ago I realized that my transmission shift occasionally while I am driving, especially when the weather is cold and I park my vehicle for more than one day. Then my engine check light came, after two days it went off. I went to the dealership and ask for a multi-point inspection (without telling the inspector the transmission problem), they recommend a transmission fluid flush, then I went to an auto part shop to ask for reading engine check light code, they see P0711. After researches online, I understand this code is about transmission fluid or transmission fluid sensor defect.
My question is that, would a dirty transmission fluid cause the P0711 code, as some people stated online ?
Subaru - B9-tribeca :: Check Engine And ABS Light Came On Along With Cruise Light Flashing
I've got a 2006 B9 with about 64,000 miles. Just a bit ago my check engine and ABS light came on, along with my cruise light flashing.
After researching a little bit on the forums and couldn't find an answer, I took it into the dealer, to which I was told that there was a bad oil pressure sensor for the right-hand side of the motor. I had them replace it out, and less than 20 miles down the road, the same lights appeared on my instrument cluster, and I took it back to the dealer. They informed me that there was now a bad sensor on the left hand side that would be another $380. I scheduled an appointment for later next week, and had them reset the error.
On the same day, about 2 hours later the lights reappeared on my dash, and I took the car over to a local parts store, where I used their scanner and the car now spit the following errors:
Camshaft position actuator A - Bank 1 timing over advan.
Camshaft position actuator A - Bank 2 timing over advan
Cam/crankshaft pos. correlation sensor A - Bank 2
Cam/crankshaft pos. Correlation sensor A - Bank 1
Camshaft position actuator A bank 1 timing over - advan
Camshaft position adctuator A bank 2 timing over -advan
Cam/crankshaft pos correlation sensor A - bank 1
I reset the codes, and waited another day for the lights to reappear on the dash. Again, I rescanned the errors, and found the same top 5 codes that I listed above.
Is there something more major going on here with the computer?
Subaru - Legacy :: Check Engine Light Turning On And Cruise Control Light Flashing
Had an issue with "check" engine light turning on and "cruise" control light flashing, intermittently. Dealer said we had dirty oil contaminating some solenoid valves in the system but we had just done an oil change and do so every 3-5K (car has 170K). They recommended switching around the sensors and doing an "oil flush" with another oil change. The warning light problem hasn't recurred, in the past month, since we started giving the gas cap a few extra turns after a fill-up. We're getting ready to buy a new car and don't want to give what might be a serious problem over to the next owner.
View 6 RepliesSubaru - Forester :: 2007 - Cruise Light Is Flashing And Check Engine Light Is Solid
I have a 2007 L.L. Bean Edition Forester. The cruise light is flashing and check engine light is solid. I am well into my retirement age and nearest dealer is about 2 hours away. Is this something that local mechanic can fix? He is very good, but not Subaru schooled. I'm afraid to drive it now.
View 2 RepliesVolvo :: XC70 - ETS Light Is On And Check Engine Light Flashing
Have a Volvo XC70 and LOVE it! Recently ETS light came on and Check engine has always been on, mechanics did not seem to worried in past. As of the last month seemed to be issue with thermostat... Car would warm to normal when idling and driving below 25 mph... once I accelerated needle would drop and thermostat would go to baseline... Could feel faint warm air, but was only getting cold air coming from vents... Thought it might be thermostat stuck open?
Called my trusted mechanic and he recommended going to a radiator specialist, felt he might not be able to solve. Went to new shop today, after dropping off at 8am when they opened and not hearing from them until 4:45pm, 15 minutes before they close... Car is fixed, or so they say. Hot air is indeed coming out of vents and needle is staying where it should without falling...
BUT, now there is a strange smell (sulfur"ish") coming from the engine, and the car is shuddering and vibrating, bucking almost when car comes to a stop and then accelerates. ETS light is back on and check engine is now flashing!?! Tried going up hill on the way home and could not go faster than 20mph? None of this was happening before I took it in to the new shop today? They changed oil and oil filter and flushed radiater?
Ford Transmission :: 2002 F350 - Tow Light Is Flashing - Code P1876 Came Up
I have a '02 F350 just over 114k miles, tow light is flashing and just had P1876 code come up. 4h and 4l engage and disengage with out a problem. Code reads 2wd solenoid circuit failure. Where is this solenoid is located?
View 1 RepliesFord Aerostar :: Transmission Code P1744 - No Flashing Overdrive Light On Shifter
I got this code and symptoms of 1-2 hard shift and no torque converter lockup. No flashing overdrive light on shifter. If I switch off engine all shifts are smooth until I pass 45mph. I would feel the TCC lockup. This doesn't happen the as i come to a stop I get a harsh 2-1 shift. Key off restart then shifts smoothly up and down provided I dont exceed the TCC lockup speed. This leads me to the TCC solenoid I think. Fluid has been changed regularly.
Had to drive 300 miles to get home. Only for the plate trans cooler the fluid would have overheated as on inclines on cruise control the engine would rev to 3k to keep the speed at 70mph and I could see the fluid temp increasing. Fuel consumption was very bad almost a full tank (with no ac). Doing some research there is talk about valve gasket blowout Epc solenoids etc, though these were for Rangers and Explorers, no real mention of Aerostar.
Ford - Fusion :: 2012 - Check Engine Light Came On Steady Not Flashing
I have a 2012 Ford Fusion SEL. In late December, the check engine light came on (steady, not flashing). I took it to a local mechanic, as the nearest Ford dealership is a 45-minute drive away. He said an evap code came up indicating that there was a problem with the vent valve solenoid, not the capless fuel filler. However, he did not have the diagnostics to research it further.
As there have been problems with the vent valve solenoid, including a recall (for which we do not qualify), my husband bought and installed the part on Jan. 7. We both drove it several times since then, and the check engine light stayed off. But when I drove it today (Jan. 11), the light was back on.
Passat (B5) :: 2001 / 1.8T - Transmission Code 18155 Or P1747
Looking for info on tranny code 18155 or p1747 is ? Car is 2001 and out of warranty..
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F250 - Auto Transmission Code / OD OFF Light Started Flashing
I bought this truck with a stock automatic transmission and 260k miles back in October expecting the transmission to be the first thing to go. Recently I had a transmission code, OD OFF light flashing, for the bad speed sensor which i got replaced. Then the OD OFF light started flashing after some hard driving when I would put into neutral or park so I took it back to the mechanic, Hanahan Truck and Auto in Sc. They looked into it and there wasn't any different code in the system but they noticed when you lay into it driving it slips some between 2nd and 3rd gears so that could cause the computer to put in a code.
They said usually a rebuild runs from $2k-2.5k and they also recommended a Jasper reman for roughly $2.8k which comes with a 100k mile 3yr warranty. So I figure replacing the transmission is probably the way to go. Any recommendations for a replacement. I've heard ATS and Sun Coast are decent options that I could build one. I'm looking to stay close to $3k. My truck is a 2000 F250 lariat 4x4 with 268k miles. I'm installing an S&B intake, 4" MBRP exhaust, and DP-Tuner's F6 chip when I get the transmission work done.
Ford Transmission :: CEL Came On And OD Light Flashing When Turn The Key And Engine Started
working on a 2000 F-150 (5.4L & 4R70W). the truck was towed to me with the complaint it would not go forward.
I found 6 transmission trouble codes set. I cleared the codes and was able to drive the truck for about 30 miles. It shifted perfectly and had all 4 forward gears, codes did not come back. I parked the truck to check the fluid level (it was full) waited about 15 mins and went to move the truck, As soon as I turned the key and started the engine the CEL came on and the OD light started flashing, the transmission would engage in forward gears but would just chatter when you tried to accelerate.
I checked the codes and found P0743, P0750, P0755, P1747 and P1760 set. I tried clearing the codes again several times and come back instantly when the key is turned on.
I doubt all the electrical solenoids in the transmission have failed at the same time. I suspect the internal connector and/or harness maybe faulty. what is the best course of diagnosis on this? where so I start?