Ford - Taurus :: 1998 - Check Engine Light Is On And Code Reads P0411
98 Taurus, 6cyl, 3.0L OHV, 184K miles. Check engine light is on and code reads "P0411 - secondary air injection system - incorrect flow". This is my son's hand me down car and has a rather large exhaust leak that I plan on fixing. Could this code be related ?? I found out that the CEL has been on for quite sometime now and the car is due for emissions testing (state inspection) in October.
View 3 RepliesFord - Taurus :: Check Engine Light Keep Flashing - Code PO302 Cylinder 2 Misfiring
I have a 1996 ford taurus lx v6 3.0 dohm..my check engine light flashing. then it stop flashing..i did replace spark plug,wires,coil pack..when it start to flash i put it gear the car start to shake and sputter.i really don't know why its doing that the car has about 150000 miles on it..i do get a code p0302 Cylinder #2 Misfire..the new plugs and wires and coil pack is about 2 weeks old..
View 11 RepliesFord - Taurus :: 2002 - Check Gas Cap Light On
Just today I noticed an indicator showing up on my dashboard. The indicator shows the passenger side of the car, and a little screw coming out of it. I grabbed the giant book of boredom (Car manual) and the indicator is one for checking the gas cap and says once the gas cap is seated properly the light will go out.
I reseated the gas cap making sure it clicked when I turned it, and drove the car for about 45 minutes (My drive back home), and the light has continued to stay lit. What seems strange is that the check engine light is not showing up, which I know typically happens if the gas cap is not on properly.
Is there a sensor somewhere in the car that will cause that 'check gas cap' light to come on, and if so is it something I could find and replace myself, or am I better off going to a shop?
Camry :: 2002 - Check Engine Light On / Code P0440
It just so happens that I got my letter from the DMV telling me I needed to get my new tags, and this is an emissions test year for my car. I was buys the last few weeks so I figured this would be a good week to do it. Yesterday.......check engine light comes on. How does that happen???
So now I'm on a time crunch. I went to Advanced Auto this morning and they checked the code. It's P0440, an Evaporative Emissions code. Any thought on what that me be, or any checklist as to what to check first? I'm fairly handy, but know nothing about cars. I'm sure I can figure it out with some instructions.
Summary: Got a check engine code of P0440, Evaporative Emissions. On a time crunch because I need to get an emissions test done. I can probably fix it myself with some direction.
Windstar :: 2002 - Car Running With Blinking Check-engine Light / Code P0306
So I had a serious runability problem back in 2012 with code P0302 (misfire in cylinder 2) and the car was barely running. I changed the spark plugs, which didn't fix the issues. Then changed the coil, which fixed it. URL...But I was a little lazy back in September 2012, the old spark plug wires looked like they were still in great shape, so I left the old wires on. I think they were the original factory wires, they had the numbers of each cylinder printed on the side. Very nice wires!
Fast-forward to the present. Car starts running poorly with a blinking check-engine light. Not good! I check the code and it is P0306, misfire in cylinder 6. So my first thought was: OK, probably time to change the spark plug wires!I changed the spark plug wires. I purchased AutoLite Professional Series wires at Advance Auto Parts, part 97047. URL...Sure enough, the number 6 wire looked like it had a little corrosion inside the end that connects to the spark plug wire. It looked like I was on the right track! Changed the spark plug wires, and ran it. It still sounded like it might be missing on one cylinder. Just a quiet ch-ch-ch-ch-ch-ch at idle. I took it for a test drive. It ran OK at low RPM's, but had no power. When I tested some hard acceleration, sure enough the check engine light came back on. Tested the code and it was P0306 again. Conclusion: not fixed yet.
OK, maybe the spark plug wire was the problem, just the plug got fouled because the wire was bad. I purchased a replacement spark plug for that cylinder only. AutoLite Double Platinum as recommended elsewhere in this forum. Removed the old plug. I'm no expert, but the old plug looked fine to me. Installed the new plug. Tested it again. Still sounded like missing at idle ch-ch-ch-ch-ch. Test drive, OK with low RPM, no power. Tried hard acceleration, got the blinking CEL again. Conclusion: still not fixed - darn it!
Now remember, I just changed the coil back in September 2012. I had replaced it with a coil from AutoZone. The first coil had lasted ten years. So it couldn't be the coil again this soon, right? But... just to be sure, I went ahead and changed the coil again. I called AutoZone and happily it was still under warranty. The previous coil I had purchased came with a 24-month warranty, and I was on month 23 !!! Sweet!AutoZone also told me if I did a warranty replacement of the coil, the new one would come with a lifetime warranty instead.The part number of the coil at AutoZone was part C1312, Duralast Ignition Coil.
Before installing the new coil, I put a little Dielectric grease around the top inside of each connector on the new coil (7 total, six spark plug wires plus the electrical connector). I think this was recommended in my Haynes or Chilton manuals.I am a tall skinny guy with long skinny arms. So I was able to replace the coil without removing the cowl. Last time I had to remove the cowl (to do the intake manifold isolator bolt repair) the cowl had cracked, also some of the clips holding it down broke. So I didn't want to remove the cowl unless necessary. It turns out with my long skinny arms I can lay up over the motor and reach back around both sides of the intake manifold to reach the coil. It is a reach, but it was possible for me to do the job that way.
I removed the three bolts holding the old coil in place. Then I was able to slide the new coil back in there, around the driver's side of the intake manifold. I transferred over the spark plug wires one by one from old to new (as recommended by another poster) so I wouldn't get confused which was which. It worked well to transfer the rear three first. That hold the new coil near the correct location, and gave me more slack to move the old coil further out of the way.Next step was to remove the wire connector from the rear of the coil pack. It didn't want to release. I looked at the old part (from 2012!!!) and there was a little plastic nub back there to lock the connector in place. It looked like there was room to work in a small screwdriver back there to release the lock. So I wiggled a short flat-head screwdriver in back there (with a wide head) and it released. Then I was able to easily remove the connector.
Then I had more slack to move the old coil further out of the way, toward the drivers side and front of the vehicle. And then transferred the last three spark plug wires to the new coil.Then to secure the new coil in place, I carefully installed one bolt by hand, leaving it loose to allow for final adjustments of position. Installed the second and third bolts loosely. Tightened the three bolts finger tight using a short (3") extension and 7mm socket (1/4" drive). Then snugged them very gently using my small 1/4" rachet. The small 1/4" rachet was a perfect fit using the 3" inch extension and the small 7mm socket. Remember you just want the bolts snug, do not over-tighten them.
When I went back to AutoZone to process the warranty return, they had to do some fancy work with their computer to get me the lifetime warranty on the new coil. By default it would just assume the rest of the original coil warranty from 2012 - which was just about to expire. So they made it right for me - but only because I specifically asked about it. By default, the guy had already rung it up their "normal" way, which would not have extended the warranty for me.Another thing that was strange was back in September 2012 when I replaced the original coil, it had worked well for ten years or so! Also, the bottom of it was clearly cracked, so it was easy to see that it had deteriorated and needed to be replaced.
Camry :: 2002 V6 Automatic Transmission - Check Engine Light Came On With Code P0770
I have a 2002 Toyota Camry V6. The warranty expired in Feb 2007. The car has only 67,000km.
The check engine light came on and the code is P0770, Solenoid E malfunction. The problem was first reported at 43,000km, when the car was still under warranty but only a transmission flush was performed and the code was reset.
I wrote Toyota and after almost two months they told me they do not cover it because is out of warranty and I do not qualify for the Goodwill program. I tried again to tell them that instead of fixing the root of the problem they temporarily covered it, but again I got a NO. No comments about the mileage, time, etc. Just the car is out of warranty and I'm out of luck.
Camry :: 2002 V6 - Check Engine Light Came On While Driving On Freeway / Code P0128
I have a 2002 v6 Camry with over 270k on it. Today the Check engine light came on while driving on the freeway. When I got home I used my scan tool and it gave me the following codes.
P0128, P0440, P0446 and P0440, P0441, P0446 pending.
I understand that the 128 has to do with coolant temp and that the other codes are evap system related.
What I'm trying to figure out is what might have caused them to all occur at the same time. I know once with my 98 Camry it threw a P0125 which had to do with coolant temp issues but it also threw several other codes for a bad 02 sensor and the 125 was just a false code (replaced the 02 sensors and they went away). If this 128 is possibly a false code or if I also have a bad thermostat/sensor on top of an evap system issue.
Also. coolant level is good and I checked the gas cap and insured it was on tight, reset the codes and am waiting to see what comes back.
Prius (2001-03) :: 2002 - Suddenly Get P1430 Code With Check Engine Light
Suddenly today, I get a "Check Engine" light while driving. Scangauge II says it's a P1430 error. I found two different suggestions, but where these are located on the car.
P1430-Electric Air Pump secondary Failure
P1430 -Vacuum Sensor for Adsorber and Catalyst System Circuit Malfunction
Ford - Taurus :: 1996 - Sputter When Stop At Red Light - Check Engine Light Start Blinking
I changed my plugs a few days ago on my 96' Taurus GL 3.0LI checked under my hood to check the recommended gap size and it said .42 to .46.. I went with .46. after putting them in i started the car up just fine, but later in the day i noticed when I came to a stop at a red light my car would sputter and my check engine light would start blinking. When I'd accelerate and drive it again everything would clear up and the light would stop blinking. I didn't change the wires, just the plugs in case you were wondering but I am unsure of how much that would influence my problem. Today after work i had a little trouble starting my car. After a few tries it started and my exhaust smelt rich in gasoline. Did i gap them too much? Should i get new plugs again and regap them? should i buy new wires also?Is my ignition coil going bad?
View 19 RepliesTaurus :: 2011 Ford - Check Engine Light On But Car Runs Fine
The check engine light came on again after coming on about a week ago and then shutting of by itself. Everything seems to run normal with the car so I don't know if I should ignore the light and just keep driving or what. What would you do? My car is a 2011 Ford Taurus.
View 1 RepliesFord - Taurus :: Check Engine Light Flashes When Start The Car And It Idles
I have a 2001 ford taurus. just changed the engine with a used engine has 130k, did tuneup changing all spark plugs, wires and distributor cap. Also changed the 02 sensor upstream. And the check engine light remains on. if i start the car and it idles the check engine light flashes. but once i drive it, it just remains on. brought to the mechanic and he put on the machine and it reads that the problem is the 02 sensor upstream and the spark plugs misfiring. my mechanic is lost not sure what the problem is. someone told me it could be the manifold gaskets and pedlum gasket.
View 1 RepliesFord - Taurus :: 2000 - Check Engine Light Came One - Misfire In Cylinders 1 And 3
I have an old 2000 Ford Taurus that has been having some misfire issues. I replaced the wires and plugs about a year ago and hooray! it worked... until about a month ago when the check engine light came one. Misfire in cylinders 1 and 3... again. I ran some SeaFoam through and it did okay until this week, when the warning/flashing check engine light came back.
It is idling very hard (expected) and feels like it is trying to stall, even before the misfire came back (also to be expected??). So here is the question: is this a coil pack issue, or something more sinister (and expensive)?
Ford :: 2004 Taurus - Check Engine Light On After Torque Converter Replaced
This car has been giving me quite a bit of trouble lately. 04 Ford Taurus SES, about 97,000 miles on it. Just last weekend, it broke down on the highway. Found out the torque converter failed and needed to be replaced. I was suspecting that something was wrong with the transmission for a while now, because it would stutter sometimes when accelerating, and sometimes start shaking in the front when I turned it on. (It still stutters after having the torque converter replaced.)
Well now, a day after shelling out quite a bit of money to the dealer for this torque converter, the check engine light is on. I went to Autozone to check the codes, and they found P0300, P0305 (cylinder misfire) and P0316 ("crank sensor condition"). Is it possible the transmission is failing?? I found a bunch of complaints online about the transmission failing on the 04 Taurus. I'm trying to avoid more expensive repairs, but I don't want the car to break down on me again....
Also, a couple months ago, the check engine light went on a few times, but always went off within a day or two. Never did get it checked out because it didn't stay on long enough.
Lexus GS 2006-11 :: Check VSC Error Code P0300 With Check Engine And Traction Light On
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
Ford Ranger / B-Series :: Code P1451 - Vent Solenoid?
So... p1451. Vent solenoid. I pulled the part and put 12v to it. Opens/closes just fine. Checked resistance on part, 55ohms like it should. Pulled vent canister, no apparent leaks or blockages. I traced wires back to cab. Cannot locate anybroken wiring. I looked up the pinpoint test on this dct and all thats left to test out is the pcm itself. Before I buy the obd2 scanner with all modes I wondering if I am missing something.
I did find a broken ground wire in my searching. Frame to body. My thoughts on a bad ground are that that would cause more than one monitor to register one fault code.
Ford Excursion :: Code P1451 For Canister Vent Purge Valve
My Ex is throwing a P1451 Canister Vent Purge valve issue. Is the canister for the Ex hidden on the frame above the gas tank? I looked around the frame in the back of the truck but am having no luck finding it so I'm guessing ill have to drop the tank to get to it. I've read that wire chafing for this valve could be the problem.
View 3 RepliesSubaru - Forester :: 2002 - Check Engine Code For Knock Sensor - Motor Mounts?
2002 Subaru Forester I took my car to the Auto Zone to read a check engine code. It came back as being a "knock sensor". Besides that I needed a battery, and when the guy was putting it in he said my engine was moving too much and that I probably needed motor mounts.
I was looking at a discussion back in 2010 and the Subaru specialist told the person needing motor mounts is rare for a Subaru, is that true? I'm taking it to a mechanic, what should I expect? how many motor mounts does a subaru have?
Ford Transmission :: Check Engine Light On / OD Light Flashing Sometimes - Code P1747
I have a 1998 expedition 4.6 4x4 check engine light on od light flashing sometimes checked it and got p1747 code i was told epc solenoid or short on trans wiring. I already dropped the trans pan, looking for a step by step easy way to diagnose and find the short or if i need to replace any of the solenoids. I have voltmeter and taste light....
View 3 RepliesLexus RX 2004-09 :: Check Engine / TRAC Light On - VSC Light Blinks And P0128 Code
08 RX350 with ~100K miles. Two weeks ago the Check Engine/TRAC light were on, VSC light blinks, so I tightened the gas cap, and pull the negative and cleared the code. Hoping this is just a gas cap issue.
2 weeks later all those lights are back again, so my mechanic pulled the code and came up with P0128. He told me it should be the problem with the Coolant Temperature Sensor. The water pump, thermostat was replaced last year and coolant level is OK. No issue with coolant temperature and the car drives like normal. My mechanic cleared the code and told me to drive it again until the lights come back and he will pull the code again.
08 RX350 AWD
08 Avalon Touring