Ford - Explorer :: 1999 - Code P1451 EVAP System Canister Vent Solenoid Circuit Malfunction
I have a 1999 Ford Explorer with the V-6 SOHC that is stuttering and stalling when I try to accelerate. A very slight acceleration will get the vehicle moving, but anything coming close to normal gas pedal pressure causes immediate stuttering and/or stalling. Check Engine light came on when problem started yesterday.
Where is the EVAP System Canister Vent Solenoid? I bought a code reader after beating my head against the truck all afternoon and got code "P1451 EVAP System Canister Vent Solenoid Circuit Malfunction". My Haynes book says on the left side frame rail... can't find anything along there that looks like it (based on picture from Rock Auto for replacement part) and found some people online talking about it being in the engine compartment on the passenger side...
Just crawled all over the truck and I think I found the charcoal canister, but couldn't trace it back to the vent solenoid... There was something right next to the canister, but again, it looked nothing like the replacement part listed on Rock Auto...
Ford Wiring/Electrical :: P1451 Code - EVAP Control System Canister Vent Solenoid Circuit Malfunction
I'm not too knowledgeable about wiring and electrical systems. I'm getting a P1451 code (EVAP Control System Canister Vent Solenoid Circuit Malfunction) on my 99 4.2. I've read that it could be a bad solenoid, bad wiring, or a blown fuse. So far I've;
- checked (and changed) the related fuse
- checked the wiring for damage at the connector
- checked voltage at the connector (12 volts)
- checked the resistance at the solenoid (around 60 ohms)
- actuated the solenoid with a 9V battery (can hear it opening and closing)
I haven't had a chance to check the wiring all the way back up the frame to yet, but I noticed that the ground at the trailer wiring harness has broken off the frame. Would this potentially cause a fault in the upstream wiring? I'm going to slap a new connector on and bolt it back down anyway, but as it's Labour (Labor) Day I'll have to wait for the stores to be open tomorrow.
Ford Excursion :: Code P1451 For Canister Vent Purge Valve
My Ex is throwing a P1451 Canister Vent Purge valve issue. Is the canister for the Ex hidden on the frame above the gas tank? I looked around the frame in the back of the truck but am having no luck finding it so I'm guessing ill have to drop the tank to get to it. I've read that wire chafing for this valve could be the problem.
View 3 RepliesFord Ranger / B-Series :: 2003 V6 - Code P1450 - Location Of EVAP Canister And CV Solenoid
A buddy of mine has a 2003 Ford Ranger Edge V6 3.0L, he got the code P1450 the other day and asked me to look at it. Got all the info on what it could be but where ex actually is the EVAP canister and CV solenoid located? And what is the problem?
View 1 RepliesSanta Fe (CM - 2007-12) :: 2009 GLS - Code P2422 / Evap Vent Solenoid Stuck Closed
My 2009 santa fe with the 2.7 has a check engine light. p2422 evap vent solenoid stuck closed. I replaced the charcoal canister and the light came back on. I replace the solenoid by the throttle body and the light came back on but took longer to set. My wife said that she was having problems filling the tank but when I changed the second solenoid the problem was gone but the light had returned.
View 6 RepliesFord Ranger / B-Series :: 1992 - Replaced Solenoid Now No Start?
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 RepliesFord Ranger / B-Series :: 1996 - Start If Turn The Key To On And Jumping The Solenoid
I have a 1996 Ford Ranger XLT Automatic with a 4.0... A few months ago I went to start it and it would not start. All the lights were on and working, the radio worked etc. I figured it was the fender solenoid so I replaced it. Didn't fix it. I jumped the solenoid and it spun up. The only way I can start the truck is by turning the key to on, and jumping the solenoid. I replaced the ignition switch that is under the instrument panel, and the ignition cylinder that the key goes in to. I have reason to think that it may be the neutral safety switch, but I do not want to go out and buy the part and it not be the issue.
View 14 RepliesFord Ranger / B-Series :: 1987 - No Power / Starter Died And Solenoid Was Just Clicking
Well it all started when I was having starter issues my starter died and my solenoid was just clicking and after time there was no power at all to anything in the truck i have replaced the solenoid and starter and check battery and cleaned post and terminals. I am going to replace my negative cable as it was pretty bad but if this still does not work, so what to look for. The truck is an 87 ford ranger 4x4 5 speed with a 2.9....
View 9 RepliesFord Ranger / B-Series :: 2003 - Heater Vent Selector Stuck On Defrost
There is always something.... I just drove my girlfriend's new 2003 ranger edge home from the seller. Real nice truck. I noticed the heater selector doesn't change the air flow. It is on full blast for the defrosters, and is also trickling out of the floor and dash vents. No matter where you put the selector, thats the only place the air comes out.
The temp control seem to work OK, when you turn it on cold, you get cold air and visa versa. Even on AC and MAx AC... air out the defrosters. It's cold when you turn the temp control to cold.
I did some searching here and gather some info on checking the vac lines etc. Everything looks in place but one detail. The vac ball under the hood under the air box has 2 ports on the front end, and only one grey line going into it. The other port has what looks like a rubber boot and part of a very short vac line broken off it.
I looked, I cant find any loose vac lines. I'd like to know if this second port is suppose to have a second line on it, and where does it go? What color is it? Is this the reason the vent selector isnt working?
Taurus :: 2002 SES Check Engine Light On And Code P1451
Check engine light on and code is P1451. I have been told its one or all four things:
1. Gas cap,
2. Evap Canister vent solenoid,
3. Evap purge solenoid,
4. Evap canister.
I am trying to fix this problem on the Taurus. I have changed the Gas cap and this did not solve the problem. The other three things on the list: Are these three separate things? Or are they part of the same thing?
Ford Ranger / B-Series :: Code 157 For MAF Sensor
So here is what I got. Code 157 maf sensor below minimum voltage. Here is what the truck does. When the MAF is plugged in and I step on it, the truck surges and when it drops below 1k rpm it dies but I can start it back up. If I hold the throttle at 1k it stays alive. When I drive with the MAF unplugged it runs better no surging but it still dies. Here is what I have done. Reset codes no change, put new MAF in no change. I have traced all 4 MAF wires checked continuity from inside of plug to inside of plug.
All wires checked out good. No cuts breaks or anything. I have checked my battery, starter, and alternator ad all check out fine. I read that someone said if the corresponding transistor in the PCM took a dumb then it would cause not enough voltage to get to the plug because the transistor would dump the voltage from the battery leading to the MAF. I thought about running a direct power source from the battery to the voltage side of the MAF with a switch in the truck to just see if that would solve the issue but I don't know if that is possible or smart.
Ford Ranger / B-Series :: 1997 - CEL With Code P0133?
I have a 1997 Ford Ranger with a 4.0L 2WD. The check engine light just turned on with a code of p0133. I know that this is something with the bank 1 sensor 1. I tried doing some research and I think that it is on the passenger side before the cat converter. Now, I don't know what to do from there. How do I go about fixing this? What part do I need? How do I fix it?
View 1 RepliesFord Ranger / B-Series :: 2001 - Airbag Code 29
What airbag code 29 on a 2001 ranger means? I have not seen that number on any code lists. I triple checked the code and it is 29.
View 9 RepliesFord Ranger / B-Series :: Got Code P0162 - O2 Sensor Or MAP?
Just checked SES code and read P0162 I think. Stated rich fuel mixture bank 1 & bank 2 (3.0) Is this an O2 sensor or MAP issue?
View 8 RepliesFord Ranger / B-Series :: 1995 - CEL Came On - P0340 Code - CPS Bad
I am having an engine issue with my 1995 Ranger with a 2.3L. I have been having a P0340 code that kept appearing after several attempts at resetting the PCM. I gave up and took it to a Ford dealer for diagnostics and they called the CPS bad. They changed it, but the CEL light immediately came on with the code still kept coming up. The service rep. showed me the old sensor, it had a spot on the head of it where it looked like something was rubbing it. I'm assuming it's slightly rubbing on the gear it points to, which is the oil pump gear, correct? The truck runs fine, no performance issues whatsoever. Is it possible my oil pump shaft has developed play in it's shaft, causing this?
View 1 RepliesFord Ranger / B-Series :: Getting Code Pesky P1443 With CEL?
I've been getting this code for a while. Changed the Purge solenoid and valve, replaced the hose from the canister to the two units, didn't change the hose to the intake.
Is there anything else to check? Could it be a bad gas cap? the one on the truck is a replacement.
Ford Ranger / B-Series :: 1994 - How To Check Code For CEL
1994 Ranger xtra cab
4x4
v6 4.0
5-speed
113K miles
Just bought this truck. When I test drove it no "check engine" light came on, but after purchase driving home is came on and then off many times. It only comes on at high rpm/speed. I have my trusty ODBII scanner but realize that this 1994 was pre-ODBII. How can I figure out what the CEL is about?
Ford Ranger / B-Series :: Code P1403 Keeps Coming On After Clear It
My 96 4x2 2.3ltr is throwing this code (P1443). I clear it and it comes back a few cycles later. I will fix it next but won't be able to get to it for a couple weeks. What if any affect does this code have on fuel mileage and or engine performance/power?
View 3 RepliesFord Ranger / B-Series :: 1999 - Airbag Light On With Code 32
My son has a 99 Ranger where the airbag light is flashing code 32. I had the same code on my F350 and it was the clock spring. What it could be. It is 99 Ranger with 2.5l, auto trans, 2wd, no CC.
View 2 Replies