Golf/GTI VI :: How To Remove Headliner
I want to change my headliner to a different design. Any info on how to remove it will be useful. Also, is it true that if you take it off you have to buy new clips or brackets?
View 6 RepliesLexus GS 2013+ :: How To Remove / Reinstall GS-F Suede Headliner
How to remove and reinstall the GS-F suede headliner?
View 14 RepliesFord F-150 (2004-2008) :: 4.6L - Remove Manifold To Replace Gaskets For Crossover?
I have a leak between the metal and the plastic of my water crossover.
Do I need to remove the manifold to replace the gaskets for the crossover and if so looking for a good thread showing how.
Ford - Explorer :: Puddle Of Water On Driver Floor - Remove Headliner?
Have a tarp over the roof of our Explorer, getting a puddle of water on the driver floor.
It's getting the headliner wet near top driver side of door/windshield.
Is there a drain tube, or is it a blocked channel in the roof that I can clean with a stiff wire from above?? or does this require removal of the headliner?
Ford Excursion :: Remove Rear Vent Windows With Headliner Still Installed?
Is it possible?
View 1 RepliesTouareg :: How To Remove Headlights To Replace Bulbs
How do you remove the Touareg Headlights to replace the light bulbs. I have fount the open close turn, but that doesn't release them all the way.
View 3 RepliesGolf V R32 :: Should Remove Taillight To Replace Bulb?
Got the light bulb symbol in the tach this afternoon. After checking it out, the LR inner bulb seems to be out. Am I correct in assuming I have to pull back the carpet, then remove 2 nuts/washers, and then remove the taillight lens/housing to replace the bulb? Any recommendations on bulb or just stay with OEM? My R32 has 88K+ miles and this is the first bulb to go...
View 5 RepliesCamry :: 2010 V6 SE - How To Remove Engine To Replace Water Pump
When the water pump goes bad do you have to remove the engine to replace it?
View 2 RepliesAccent LC (2000-05) :: How To Remove Caliper To Replace Pads And Rotors
I need to replace the rotors and calipers on my 04 accent gl. I noticed there are 5 bolts on the back of the caliper. I know one is for the flex hose connection. Then there are 2 big hex bolts closest to the dust plate. Are those for the caliper mounting bracket? and if so will they need to be removed? Then the final two are on the outer edge, however the top one is rounded and rusted, is this normal? The one on the bottom is a hex. So what needs to be removed to change the rotors and pads? I also notice that there are two screw holes in the rotor, that I guess snug it in place against the hub, however the screws are missing. Is this bad? are they needed? and if so can I get new ones?
View 10 RepliesPassat (B5) :: 2003 - How To Remove And Replace A Busted Lock Cylinder
How to remove and replace a busted lock cylinder. My wife's car got broken into and used something that punched in the driver's door lock cylinder. VW wants top replace a new lock cylinder. I've been able to remove the drivers door panel but I wasn't able to figure out the final steps.
View 1 RepliesPassat (B6) :: How To Remove / Replace Left Outer Taillight Assembly
2008 Wagin .... Specifically, how do I remove the reflector plate that hides the bolt?
View 3 RepliesCamry :: 2002 - Remove And Replace Burnt License Plate Bulb
02 Camry, how to I remove the burnt license plate bulb? Took off the underside trunk carpet and disconnected bulb harness, but I don't know how to remove the plastic piece that holds the bulb in place. Does it pull out, or twist out? I don't want to break it!
View 1 RepliesCamry :: Remove / Replace Rear Bumper Cover On 2003 Vehicle?
How to remove and possibly replace the rear bumper cover on a 2003 camry?
View 4 RepliesPassat (B5) :: 2002 - Front Side Marker Lights - How To Remove / Replace
My 2002 B5.5 Variant received some "tough love" in a parking lot recently, with the result that one of the front marker lights (in the fender ahead of the front wheel, on the side) was broken. I see that I can push on the light housing and it'll move in a bit, but how can I remove the cover (the colored plastic bit) entirely to replace it with a new, not-busted one?
View 1 RepliesGolf IV R32 :: Replace / Remove Center Mesh Grill On Front Bumper?
I need to replace the center mesh grill on the front bumper. Is there anything I need to be careful with or watch out for. when I pull on the old grill or when I push the new one back into place? Does it come out easily or is it tricky?
View 4 RepliesPassat (B5) :: How To Remove Front Turn Signal Socket To Replace Bulb
I have a 2003 W8 wagon and my front turn signal bulb went out. I need to replace it, but am having some problems. I removed the high beam cover to get to the turn signal socket, but I am having problem removing the socket. I was able to turn the socket slightly and was hoping I could just pull it back, unfortunately it doesn't seem to want to move. Is there a trick to remove the turn signal socket so I can remove the bulb? I don't want to force anything in fear of breaking something. there has to be a way.
View 1 RepliesFord F-150 (2009-2014) :: How To Remove Tailgate Assist Handle And Replace Lid
I though I would like the tailgate step and assist handle. They are always in the way and I want to get rid of the handle but keep the step if possible. Can I remove the plastic tailgate cover, pull the hande and re-install a metal tailgate cover.
If not, want to swap a tailgate. Its red, has the back-up camera and, no dealer markings and in excellent condition.
Ford - Explorer :: 2002 - Replace Valve Spring - Remove Engine?
Thats what my mechanic told me about my 2002 exploder sport trac with 4.0. I started another thread here a while back about my truck having a bad miss, turns out it has a broken valve spring. He said the engine must be removed to do the job as its on the #1 cylinder which happens to be on the passenger side and the cam chain drive is on the back of the block.
He said my choices are: Remove the engine and just replace the spring, which may or may not effect a repair as theres no way to know if the valve made contact with the piston. Remove the head and send it off to a machine shop for repair/inspection. Or, remove both the heads, one for repair and inspection, the other just for inspection, and then put the whole mess back together.
Whats the best option here? I'm not exactly made of money, and, I'm still licking my wounds about having such a mechanical disaster take place on a vehicle that up until this point, I absolutely loved and has only 90,000 miles on the clock.
Ford Super Duty (1999-2016) :: How To Remove Driveshaft To Replace U-Joint
Rear-most connection before pumpkin, need to replace the U-Joint. I got the four bolts out at the flange but the shaft won't drop. I beat on the connection a bit, not enough to hurt though. What am I missing? How the heck do I get this apart and drop the shaft to replace the U-Joint???
View 9 Replies