Golf IV R32 :: Random Misfires On Cylinders 4 / 5 And 6
I am getting random misfires on cylinders 4, 5, and 6. Mostly on 6, less on 5, and even less on 4. Cylinders 1-2-3 show ZERO misfires. I am using vag-com to monitor these. Mostly doing it on idle, cruise seems fine but occasionally when shifting I feel it when engaging the next gear. It doesn't buck but I feel a little hesitation. Cruising and accelerating I do not feel it. Its very strange. A couple times during extended idling I have even gotten a flashing CEL. Fuel mileage has been pretty bad ever since I got the car in December. Average tank gets me 250-270.
I tried swapping coils with 123, and the problem stayed on 456. Coils are all new since I got the car. Plugs are fairly new (under 5K) and I pulled a couple to check, they looked fine and gap was about .028. I might try a new set but my gut is telling me the problem is some where else. I would like to verify/test grounds but I don't know where the harness grounds out.
I also want to get a vacuum gauge on the FPR, or check fuel pressure at idle. I replaced one cracked vacuum line, i am thinning there might be others since there seems to be miles of vacuum line on MK4's. Also have a new fuel filter to install, mine appears to be OEM and the car has 97K.
Golf IV R32 :: Code For Misfires In Cylinders 1 And 2
My girlfriend's MkV Jetta 2.0T is throwing a code for misfires in Cylinders 1 and 2. I've already switched out the plugs and coilpacks with no change. I'm going to try re-positioning the coilpacks to see if the code follows. In doing some research, someone mentioned that it could be fouling on the injectors, which led me to BG44K. She has >215K miles. I figure she's gotta have some fouling that could be cleaned up. I have ~110K miles on my R32 - I figure it wouldn't hurt to do some cleaning in my own car.
View 4 RepliesGolf/GTI VI :: 2013 - Recurring Misfires On All 5 Cylinders
I'm getting random misfires on all 5 cylinders on my 2013 2.5L with ~4200miles. Sometimes the CEL will stay on other times it just flashes and goes away. I've gone to multiple dealers and none of them has done anything but clear the codes because "we couldn't replicate the issue," or "It's just rev hang/drive by wire."
What are the known causes of a brand new car misfiring? And what should I have VW look at?
When I mentioned that our family has a 2007 Eos all three dealers were chomping at the bit for me to bring it in for recalls I didn't even know about. This really rubbed me the wrong way. I've got one car that I KNOW is malfunctioning that VW won't do any work on, but the other VW is volunteering to work on!
I've got another appointment set for tomorrow after I get off work. How to push the right buttons or say the right words?
Golf IV R32 :: Misfires In Low RPM Range / Stumbling And Just Not Firing On All Cylinders
Ok so I'm having weird issues with my big turbo R. I thought I was having misfires in low rpm range. Car was stumbling and just not firing on all cylinders ( just an expression but that's what it felt like) realized it was because of the esp. Ok no the main issue. Vacuum was sitting around 14hg. When I come up to a light or stop sign or just put in neutral while moving it revs it self ad vacuum will go to almost 0hg until I come to a full stop.
The rev is not a big rev only like 100-150 rpm increase. Also the throttle response is not there if I go to rev match down shift. Here's the weird part. If I unplug the Maf it runs super smooth 19-20hg vacuum amazing throttle response clutch chatter almost goes away. There are no cel with or without the Maf plugged in I have logs for both...
Golf IV / Jetta IV :: Multiple Random Misfires In All 4 Cylinders Came Up / Idle And Boost
I have a mk4 1.8t Gti. Recently I have been having issues with idle and boost. I read the codes and multiple random misfires in all 4 cylinders came up, idle control and the crank, knock, and o2 sensor came up. Shows that system is running to lean as well. I changed the spark plugs and wires, check the coil packs they where done about 1k miles so I expect them to be perfectly fine. When I clear the codes it idles below 9-8k rpms. I also noticed the breather hose coming out of the valve cover into the EGT has a hole melted into it, could this cause any of my issues?
View 2 RepliesPassat (B5) :: Random Misfires On All 4 Cylinders
OK. I have a 2005 Passat 1.8t fwd. Tiptronic. 105k
The symptoms i am having is random cylinder misfires on all 4 cylinders. I have scanned with vagcom multiple times and get the same codes. However, I have cleared the codes, and wen fpd a 60 mile drive on the turnpike. Not a single code. So everything is perfect as long as the car dissent have a chance to idle.
I have also driven the car while logging misfires and only get misfires at idle. Never while driving.
So much has been done to the car that is so hard to decide where to start. Ill try to go in order of events.
All this in the past 4 weeks by the way.
Took car to very experienced VW tech. Found out.timing was off by 3 degrees. So new timing belt, water pump and all. Started car, still had misfires. Noticed wetness on head gasket. And did a compression test. Very bad results. (I can't remember the numbers but they were way off from each other) So he removed the head. He said there was a crazy amount of carbon buildup in the combustion chamber. Everything was cleaned, head inspected for bent valves and everything looked perfect after cleaning. (this car has NEVER overheated by the way) He said it is very rare for a head gasket to fail on 1.8t's . So he did a leakdown test and turned out the piston rings were shot. So engine was rebuilt. All components cleaned of carbon, replaced all parts, bearings with new OEM parts. Pickup tube cleaned along with other oil lines. Turbo was inspected, and I was told it is on its way out but still has life. So that was let go for now. All reassembled and all hoses checked, combi valve cleaned, new k&n filter in stock airbox. So he told me the car is finished after all that. I was excited! Drove the car home 15 min drive, ran great. Parked in my driveway, put it in park and misfires came right back. Called him the next day and brought the car back. He looked over it and replaced the fuel pressure regulator with new. He said it seemed like a fuel starvation issue. Tested fuel pump and it was towards the low end of the proper operation value. So I had a high flow pump sitting at home brand new and I brought it down and put it in. Still misfires but a lot less than before. Also fuel filter was replaced. So next he disconnected the cat And found it was clogged. Replaced with my old Audi one, and it ran fine. And this is the first time the car idled good enough to get all the monitors set for emissions testing. So he was convinced it was fixed. Room it for a test drive and came back, parked And began misfiring again. So I was so sick of this thing at this point, I told him to replace the Turbo with brand new OEM unit. And it still misfires.
He swapped a known good throttle body into it and no difference. He also said that he started going around and unplugging sensors and the more sensors he unplugged, the better the car ran. He was curious whether the ECU was faulty. So he put an ECU from his Audi in it which had a ko4 file in it. He said it ran amazing!! So he modified an ECU from a stock Audi and that's what I am driving with now. Still same symptoms. But not as often. Also brand new bosch mass air sensor was installed as well. So this is as far as we have gotten with it and I am so sick of this car right now. But we are both determined to get this thing fixed! And after all the money I have just spent, I can't even get rid of it or I will lose a lot of money. It really sucks because I love the car and so does my wife. And out of the three 1.8t's that I own, I have never had any major issues like this.
Santa Fe (CM - 2007-12) :: 2008 - Misfires On All 6 Cylinders
Just replaced all 6 plugs after getting p0300-p0306 codes. Still getting all codes, always starting with p0305. Was told coil was bad cause the shop only was getting p0305, but I have all misfire codes. We have over 95k on it, have owned since 2008. Its the 2.7 in it.
View 11 RepliesGTI 337/20th Anniversary :: Misfires In Cylinders 2 And 4 One Or Two Times A Day
Okay vortex here's what's happening in my 20th. About a month or so ago a CMP sensor went out, so I replaced that with a OEM sensor, on my way home my car started to misfire. So I took it easy the rest of the way home. The next day I started my car up and there were no misfires, drove to school, still no misfires but the check engine light was still on from the night before, after school on my way to get the codes ran it started to misfire again but then it stopped a few min into the drive.
Ever since then it has misfired but not all the time but maybe 1- 2 times a day then it would stop misfiring after a few min/seconds. My and my friend did the coil pack test and all the coil packs were good, yesterday (10/14/10) I replaced my plugs with NGK BKR7E plugs gapped at .028, my car is chipped with unitronic stage 2 tunning and it still misfired. I am going to clear all the codes and restet my ECU, but can you till do that with a unitronic ecu?
Passat (B5) :: 2001 / 1.8T - Multiple Misfires On All Cylinders / Lean Air Code
I have a 2001 1.8T Passat. I bought it used recently and have had tons of problems. I have been getting a lean air code for some time now and I think I recently resolved that. I had to replace a few vacuum lines, MAF, exhaust flex pipe (it was broken), fuel filter and fuel pressure regulator. The car was still running bad and throwing a lean air code (Bank 1) so I finally changed the O2 sensor and I think that did the trick. Now every time I start the car I get misfires until is warms up. I get misfires on all cylinders along with the multiple misfire code.
View 5 RepliesTiguan :: Random Cylinder Misfires On All Cylinders With Rough Idle
I have 11 tiguan 2.0T. When I start it up is runs rough below 1200 rpm. The check engine light starts flashing. The codes are all 4 cylinders for random cylinder misfire. When I go drive it around the roughness calms down but doesn't go away and the idle will start jumping up and down. It goes to 1500 back to 800. Then 1700 back to 800. It had even hit 2400 once. I have changed the pcv about 2 months ago. I checked it and it looks fine. One place said maf. I cleaned it and no change. Running out of options.
View 2 RepliesFord Excursion :: Rain Causing Misfires In 2 Rear Cylinders On V10
My 2000 Excursion, 6.8L V10 misfires when I try to start it, after a rain storm, and for the longest time, I could not figure out what was going on. After much use of a garden hose, to make rain, I found the rear two cylinder wells, on passenger side fill with water, due to a design defect in the engine hood that causes run off down that side of the engine. I visited with a mechanic, and was told that the hood design is common to a lot of the F series trucks, and the 8 and 10 cylinder engines are prone to the water buildup in the passenger rear spark plug wells. I am going to try to put a shield of some sort, around the two cylinder wells, to divert the water.
View 7 RepliesCamry :: 2007 V6 - Ignition Coil Failure / Multiple Misfires On All Cylinders?
I'm getting Codes: P0300-306 (Misfires) and P0356.
I have researched the definitions of these codes and see that P0356 indicates an ignition coil failure on coil "F" (which would be Cylinder 6?)... but how is it possible only one coil is failing but I'm getting multiple/random misfires on all cylinders?
I've looked at the wiring diagrams and the only place that I can see a "single point failure" that can cause such a thing, would be the ECM itself...
Sebring - Chrysler :: Rough Idle And Engine Light Comes On / Codes Read Misfires On 1, 3 And 5 Cylinders
I have a 2006 Chrysler Sebring Convertible 2.7L engine. Replaced water pump and spark plugs. We triple checked the alignment on the chain and are sure the timing is fine. Car started right up. Now running rough idle and engine light comes on. Codes read misfires on 1, 3, and 5 cylinders.
View 8 RepliesGolf IV R32 :: Misfires On Cylinder 5 And 6
How the cylinders are numbered as your facing the car from the front left to right (forgot the order) so I can replace coil packs on cyl 5&6 (238 misfires in 2min is not good).
View 4 RepliesGolf/GTI VI :: CEL / ECU Lights Came On - Now Misfires?
I am out of town for the weekend and my car just decided to throw a CEL and EPC light. Immediately felt a loss of power and I thought maybe limp mode. Got to my friends house, turned it off, and now when I turn it back on, it feels like it is miss fireing (I think, I dont know because I dont know what miss firing is supposed to feel like) The car is vibrating at low RPM and it does not sound smooth if you know what I mean but it smooths out if I give it a bit of gass, but not compleatly.
Could this be a bad ECU? (thought maybe since the EPC light was on but I dont know if that means ECU or something else) but the EPC light has not come back on when I restart it, but the CEL does blink continuously. It is Saturday night and I have a 2.5 hour drive tomorrow. Obviously no way to get it looked at it tomorrow, so can I limp it home at 40? The car has not failed to start yet, and I thought a bad EPC would mean the car would not start.Or if I can just drive real slow.
Golf/GTI VI :: Noticed A Series Of Misfires
Yesterday it was the coldest day my car has ever experienced at -27*C or -16F. I only live about 10 minutes from work in stop and go traffic so the car barely reached operating temp as I was arriving to work.
After about 10 hours, I went outside at the end of the day, the temps had warmed slightly and I started the car and let it idle for about 1 minute before driving off. After about 45 seconds I got a series of what seemed to be misfires. The EPC light flashed but eventually turned off, and where the odometer normally appears there was an exclamation point next to a symbol that looked like cruise had been activated. A message appeared in the MFD to the effect of "malfunction - bring car for service"
I reved the car slightly a few times-all seemed good- and left. All was good. Stopped the car a few blocks after and restarted and the warning symbol was gone and all was back to normal.
Today has been warmer and there have been no issues with it.
Golf V R32 :: Persistent Misfires At Idle
In the last few months, I've been having misfires at idle. I didn't realize at first what the vibration was, since I had cams installed over the summer and had my flywheel replaced a couple of weeks ago. I have replaced the plugs and coil packs and for a couple of days, it ran fine. Tonight, they started up again, mostly in a single cylinder. I swapped out coil packs - no change. Switched plugs between two cylinders - the misfire followed the plug. Swapped in an old plug - things improved, misfires went from 2-3 per second to maybe one every 5-10 seconds. Few to no misfires when revs go up. My battery is 5 years old, could that be an issue? Wire harnesses - do they go bad?
View 24 RepliesGolf IV R32 :: Lumpy Idle And Misfires Under Load
I've got a R32 with nearly 100K miles on it. Several days ago I was adjusting my shifter cables and am not sure if i accidentally leaned up against any sensors or their associated connectors that are in that vicinity. I took the car for a drive to feel how the shifter adjustment had turned out. I was building engine RPM from 2500-4000 RPM, I let off the acceleration pedal and felt a small and new kick as if something got loose, popped off, or backfired. Not sure what it was but my engine started to misfire in what seemed to be in several cylinders. It idles rough but the needle doesn't exceed 1000 RPM during idle. When driving calmly, there is sporadic misfire. If pushed hard to build RPM, it will misfire heavily.
I scanned the vehicle and got the following codes,
P0300
P0301
P0303
P0305
I've checked
- Every hose I can see and feel for Vacuum leaks
- Checked all my fuses
- Swapped coils from banks 1,3,5, with 2,4,6
- Disconnected, cleaned and reconnected camshaft hall sender sensors and tightened the bolts.
- Have erased the coded and the same codes are back.
Golf IV / Jetta IV :: Misfires At High Acceleration
My GF recently picked up a 1.8t (AWW) and we scanned it with vag com before she bought. We knew it had some misfires and a few other small problems so when it ran at higher RPMs we didn't think anything of it.
Fast forward to now after replacing some parts (hoses, coil packs etc...) and still the RPMs seem a little high compared to my mk4 vr6. On the streets in 4th gear, my car stays around 2200 and on the hwy its probably around 3300 in 5th gear at 75mph.
On the streets, her 1.8t seems normal but on the hwy in 5th gear, she's at nearly 4k. So my question... Do 1.8ts run at higher rpms under normal driving?