Golf IV / Jetta IV :: 2000 - Way To Install CV Axle?
I am stuck in the process of replacing a driver side CV axle on a 2000 Jetta VR6 automatic. I followed a Youtube video that may have misguided me. I removed the ball joint connection to take out the axle. (I will need a alignment after all this.) I was able to take out the old cv axle, but unable to put the new one on. While taking out the old one, the strut sank 2 inches. I then disconnected the suspension from the braking system, so it would be lighter and easier to push the strut up. However, it will not budge upwards. Do I need to compress the spring? How to move the strut up?
View 14 RepliesGolf IV R32 :: Front Swaybar Hitting Axle After Lowering
I just installed some Neuspeed sport springs with Koni sport shocks on my .:R and it appears like my swaybar is knocking against my front axle on the driver side.
Now, I read somewhere that is not supposed to be possible, but I can see the marks on the axle. Also, the swaybar link looks like it is twisted quite a bit with the new struts. And, when I look at them with the car on the ground, the distance between the swaybar and the axle looks to be at least 2 inches.
Do I need to center the swaybar? Maybe my control arm bushings are worn out really bad? The camber on the front of my car is -1.4 on both sides.
Golf VI R :: Sway Bar Rubbing The Axle Under Heavy Compression After Lowering?
I lowered the car on H&R sport Springs with Koni Yellows. On the front right, the sway bar is rubbing the axle under heavy compression (pot hole, sharp dip, bridge joints, etc) and is rubbing the lower control arm (opposite direction) on the driver's side... I got an alignment when I lowered it and it was "within specs"...
I put on adjustable sway bar end links and lengthened the passenger side 1/4" and shortened the drivers side 3/8". left side is slightly better but right side seems almost worse... all rubbing was minimal (barely through the paint on the cast iron parts and nearly no marks on the axle... both strut bearings are new. is it possible that it could be the alignment? Just seems odd to me that the sway bar end links need to be varied lengths to clear....
Golf IV / Jetta IV :: Rear Suspension Rattle After Coilover Install
This previous weekend, my buddies and I finally got my FK coilovers installed on my GTI. I have heard that people say there is a little bit of rattling upon them getting properly seated. Well it has been 4 days of driving and now sounds like the rattling has gotten worse! I took it into a local suspension shop and they couldn't put a thumb on it. We in-turn found out that my rear hub bearing was going out and has since been replace. Having issues with coilovers? I have contacted the company that I purchased them through already and am awaiting feedback from them.
Pic of the car in question. (Before coilovers)...
Golf V R32 :: Suspension Install, Axle Puller Needed?
I am doing the coilover install this weekend and plan to remove the axles. Is there a way of removing the axles, without buying and using a puller?
View 13 RepliesGolf IV / Jetta IV :: 2004 GLS 1.8t - Lowering Spring
My wife has a 2004 jetta gls 1.8t we just got some stock 18" bbs gli wheels . she wants to lower it some. Not really wanting to spend the money for coil overs... she will never adjust them and shes not racing it... just want it to look better. How much to lower it...
View 9 RepliesGolf IV / Jetta IV :: Single Turn Down Tip On Muffler
Putting a magnaflow muffler on the 99.5 2.0 slow jetta on Wednesday and I realized I don't have a rear GLI lip. Any single turn down extension off a muffler ? Or just run a straight pipe off the muffler ? Clearance with the rear lip issues ?
View 4 RepliesGolf IV / Jetta IV :: OEM Muffler Replacement Without Lift?
I removed the old muffler but it was severed at the pipe so there was no issue getting it over the rear cross member. I dropped the center brace to remove the resonator from cat back.
My question is, is it possible to install a new OEM rear muffler without a lift? I have stands but I do not know of I can get it high enough, or if I even need to get it that high? Not sure the bend of the pipe before it meets the resonator.
Corolla / Matrix 2009-13 :: 2011 - Way To Install Lowering Springs?
This is my 2011 Corolla S with Subaru Brz wheels. I got the entire set on October. It just took from a brand new Brz with Michelin Primacy HP tires. It looks on my corolla. Now I want put the Ei Bach Springs on my car, where is the good place to go?
View 2 RepliesGolf IV / Jetta IV :: 2004 GTI - Popping Noise From Underside Like Muffler Came Loose
I was driving home and suddenly the underside of my car *popped* and it sounded like my muffler came loose. Very loud exhaust/turbo whistle.
Luckily I was very close to home and was able to pull in when it completely fell off and started dragging on the street. What part of my exhaust is this and what should I do to repair it?
I just finished fixing a ton of stuff on her and now she does this ?
Golf IV / Jetta IV :: How To Install Wheel Studs
Got the stud conversion kit from ecs couple weeks ago and got them installed. I'm not sure if the engineers that designed these cars sat down in a room and decided that they were going to produce these car in such a way that it causes to work hard on unless your vw themselves. (Marketing may have played a roll) But If you have a German car with stupid ass wheel bolts you know how annoying it can be wasting time doing a simple task so get this kit. One of the best things I've purchased to make working on the car a lot smoother.
Get them hand tight. I used red loctite for high temp. Didn't take a pic of it since I decided to do this near the end. Tighten bolts together so the second one doesn't spin. Tighten em down. Tight! Rear. Longer for wider spacers. Never have a hard time pulling wheels off and putting them on again.
Golf IV / Jetta IV :: Hard To Reverse After Shifter Bushing Install
Installed some shifter cable bushings. But now reverse is harder to get to. Instead of just pushing it down and left for reverse.. Now I have to tilt the shift know slightly towards 4th gear then push down and go left and the gate seems so much smaller now. Overall it doesn't feel that much better than stock. what could i have done wrong?
View 6 RepliesGolf VI R :: How To Remove Trim For Rear Camera Install
How to remove the rear side interior trim? I want to install a rear view camera. I need to pull the trim to run the wiring along the left side to the floor and to the front of the car.
My understanding is I need to get access to the left rear side of the hatch, then underneath the carpet along the rear door trim, etc. I've seen some posts on the 2 door, but there appear to be differences between that and the 4 door.
Golf IV / Jetta IV :: 02 - Axle Came Loose From The Tranny
I have an 02 Jetta the the left CV Axle came loose from the tranny/axle flange. I checked the Bentley and it shows that a bolt holds the flange on, I guess a spline. My question when taking one off, is there anything inside that will drop/pop off when I pull it? The reason I need to take it off is that some of the bolts actually broke off, while others screwed their way out. Not sure why they came out or what made the others break but they did. It would be so much easier to get the broken bolts out with the flange out.
View 2 RepliesGolf IV / Jetta IV :: Rumbling And Clicking At 30+ MPH - New CV Axle Broken?
I have a 2001 gti that I just changed the cv axle on and it feels like it's failing already but there's no play in the axle or place it mounts to the tranny.. Doesn't feel like the last one I removed but rumbles and clicks at 30+mph.
View 1 RepliesGolf/GTI VII :: Intermittent Clunking Sound From Rear Suspension After VWR Spring Install
I recently got an MK7, coming from a MK5, and I installed the VWR springs 8 days ago. Since then I've noticed an intermittent clunking sound coming from the rear suspension. I installed springs on my MKV without any issues and again on several other cars, soIi'm familiar with the process. Everything was torqued to spec after the install.
My best description of the sound would be a clunk, not any rattling, clicking, or squealing. The sound is greater in the passenger side rear than the drivers side rear. No issues with anything up front. Sometimes it occurs when I'm turning the steering wheel while backing out of parking spots and driving slowly, other times when I hit bumps in the road, but it is not constant nor does it seem dependent on the size of the bump/pot holes in the road.
What may be causing this? My plan was to give it a week for everything to settle before I tore everything apart to look for any culprit.
Golf IV / Jetta IV :: Axle Popped Loose, Spilling All The Tranny Oil
So I just had my transmission replaced because my cv axle popped loose and tore a hole right into my old one spilling all the tranny oil all over the road. I was able to find another used one and then bolt it up and now I have a small issue. Its been leaking a little bit of tranny oil through the one piece on the bottom that has two bolts on it and a VW logo on it.
View 5 RepliesGolf IV / Jetta IV :: Sway Bar Laying On Passenger Side Axle
I recently just lowered my gti and I noticed that the sway bar was laying on my passenger side axle. I put adjustable end links on but that did not got the problem either, this car I daily drive.
View 10 RepliesGolf IV / Jetta IV :: Axle Makes Humming Noise When Stopping
So I just but my golf about a month ago and have hit many problems but the most annoying is the hum I get at 3500 rpms. In my searching I feel somewhat confident this is caused by a cheap right axle replacement. I also went under and found on the left axle markings that indicate its is oem VW and I was unable to find these on the right side. anyway I have found this: [URL]....
It says it is a hollow axle right there and it is 170 less than the cheapest oem one I have found. would this workout?