Ford 6.0L Power Stroke Diesel :: 2003 F350 - Drive Shaft Pulled Out Of The Spline
2003 f350 6.0 diesel, driving on the freeway at 70 mph, all instrumentation went off, the radio went off, the engine was still running fine. While pulling off on the off ramp, when the speed was about 20 mph the rear end jumped up as if the transmission was trying to go into reverse. After traveling about 4 miles at about 15 mph the rear end jumped up about 6 inches and the drive shaft pulled out of the spline and drove itself into the pavement. Why this happened. I have put two new batteries and an alternator in the truck and it has been fine every since, but I am still concerned it may happen again. The truck has a 6 inch lift on it.
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Drive Shaft Removal To Grease The Center Spline
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesGolf IV / Jetta IV :: ARB Rubbing Drive Shaft After Lowered
Had the common problem of ARB rubbing the drive shaft after I lowered an extra 15mm - It didn't rub before I went this extra 15mm. I got adjustable drop links on and they also didn't work. I basically told the garage to sort it out and they put standard drop links back on (not genuine) and also new wishbones because I needed them. Got my car back and the rubbing was even worse. So I raised it back up the 15mm, to where it was before the rubbing started, yet it's still rubbing like crazy. I'm wondering if the new wishbones may be causing this because of new bushings or something and it all being tighter. And also what am I supposed to do? I shouldn't have to buy a whiteline ARB because it wasn't rubbing at this ride height before the wishbones and drop links were changed.
To summarize:
>Lowered car extra 15mm, rubbing started
>Drop links and wishbones changed, rubbing is worse
>Raised back to the point where rubbing started and still rubbing just as badly.
Golf IV / Jetta IV :: Steering Rack And Pinion Shaft Connection
I just finished my first MK4 steering rack replacement (don't work on too many VWs), and when I placed the steering shaft from the column onto the shaft from the rack and bolted it down, there was still some clearance (see photo). I was able to get the bolt tightened down ok, but the clearance is bothering me.
View 2 RepliesGolf IV / Jetta IV :: Driver Side Drive Shaft Replacement?
Found some cracks in the outside of my driveshaft. 2002 Jetta 1.8T 5-Speed Manual.
Part number: 1J0 407 271 GJ
I'm guessing it's just rust/age. Honestly, I don't even know if this need to be replaced. CV boots are in perfect condition, now cracks or leaks whatsoever.
Golf IV / Jetta IV :: 2001 - How To Access The Transmission Input Shaft Seal
I'm trying to get to the manual transmission input shaft seal on my 01 GTI w/12V VR6. I've removed the 3 bolts surrounding the input shaft but the metal shroud underneath the 3 bolts seems to be adhered tightly in place. You can see the 3 bolt holes and metal shroud in this photo: [URL]
Am I on the right track in trying to remove that shroud? If so, how do I loosen it?
Golf IV R32 :: Popping Noise Coming From The Rear End Or Drive Shaft
so my r32 recently started making a nasty popping noise. the sound seems to either be coming from something in the rear end or drive shaft. not sure why it happened. i went on a 2 hour trip. got there parked it. aired it down (bags) but then when i came back and when to drive it again. it all of a sudden it started making a horrible popping noise. i thought it was the front wheel bearing going out since i knew it need to be replaced but i did that today and its still making the noise.
The noise sound just like a RWD car with a welded diff when it turns. kinda has that locked rear end hop popping noise. i lifted the whole car off the ground and put it in first to let the tires spin in the air but of course theres no weight on them so it doesn't make any noise. i'm really stumped on what it could be. im going to take the driveshaft off and see if it still dose it. then i know its for sure in the rear end. What it could be?
Golf IV / Jetta IV :: Loud Clang When Pulling Out Of Parking Lot - Drive Shaft Popped Out
So I was pulling out of the parking lot at work in first gear going about 10mph when I heard a loud clang and lost power to the wheels, I just had the car towed home and its dark out so i haven't gotten a chance to really take a good look.
My question is, how did this happen? the car is lowered on coils. I also Installed a B&M short shiftier about 3 weeks ago, i doubt it but could that have anything to do with this?
Jetta - Volkswagen :: 2009 - Crank Shaft Cradle Leaking Oil
Last year I had carbon deposits cleaned on all 4 cylinders and fuel injectors replaced at a local shop. The same shop that did this work is now telling me that my crankshaft cradle needs to be resealed because it is leaking oil. There wasn't an oil leak issue prior to the carbon cleaning and replacement of injectors and they were the last people under my hood. I am wondering if this leak could have been caused by faulty reassembly or other damage after cleaning the cylinders and replacing the fuel injectors? I have a 2009 Volkswagen Jetta 2.0 with about 75,000 miles.
View 8 RepliesFord Super Duty (1999-2016) :: 2015 - Alignment Of Front Spline On Rear Driveshaft?
Proper alignment and re-installation of the front spline on the rear driveshaft of my 2015 F350.
I removed my rear driveshaft recently (it slipped right out upon removal without any force or resistance), and I'm getting ready to re-install it again this weekend, but I've noticed that one of the grooves between the array of male splines on the shaft itself appears to be slightly different than the rest - it seems to be slightly wider. It even has a white-colored stripe of paint down the full length of the groove as if it were denoting it as being somehow different from the rest?
Problem is, when visually inspecting the splines on the inside of the receiving yoke (the part that the spline fits into), I do NOT see any such differences. In other words, it doesn't appear that there is only ONE way to properly insert the front splined-end of the driveshaft. What am I missing here?
Is the front splined-end of the rear driveshaft intended to be inserted into the yoke in ANY position around the dial? Or is there only ONE specific position or orientation that it is intended to be inserted or installed? NOTE: I've seen references elsewhere on-line that seem to indicate the need for proper alignment when there are multiple U-Joints, and maybe this is a part of it (?), but I'm not quite sure which U-Joints to consider or how to interpret such an "alignment".
Golf IV / Jetta IV :: Smoke Coming Out Near The Airbox
I bought this 2003 gti in July, noticed a little smoke coming out near the airbox but the motor had been cleaned recently so I assumed it was whatever they used cleaning it just burning off.
Today, installing an air filter, I see that there is a rubber hose dry rotted with smoke coming from it. I don't know what it goes to or how to replace it. The car drives fine. I do have CEL on for a coolant system fault, but all fluids are level it's not overheating and it doesn't seem to be losing any power.
Golf IV / Jetta IV :: Dash Lights Not Coming On
The switch for my lights have been giving me some issues recently. When I switch it on its turns on all my exterior lights but my dash lights don't come on. If I play with it for a little switching back and forth it will eventually work but it's really annoying.
View 2 RepliesGolf IV / Jetta IV :: Overheating - Fans Not Coming On
As the title says, car is overheating. Car gets to 190F within a couple miles drive. Temperature fluctuates between 190F and 225F.
Water pump was replaced ~2 months ago. Was not overheating prior. Temp reached 190F and stayed. Currently has the "black top" coolant temp sensor.
I noticed the coolant fans are not running after I turn the ignition off. This time of year they would usually be running after turning the engine off. If car is overheated and with AC off the fans do not run while engine is running.
I used the guide below to try diagnosing the cause: [URL] ....
Remember both fans should come on in slow speed any time the key is on and the AC is on - if the temperature is above about 32 F (0 C). Both fans run with key on and AC on
S180 (fuse 8, 30 amps, green plastic, above battery) must be good for slow speed operation.
Fuse and holder look good: no melting, no discoloration.
S164 (fuse 3, 40 amps, metal strip, above battery) must be good for fast speed operation.
fuse looks good: unbroken.
To ensure the AC circuits and the Fan Control Module has power check:
Fuse 5 on the cabin fuse panel.
Fuse 16 on the cabin fuse panel. When this fuse is blown the radiator fans will often run unexpectedly.
Fuse 25 on the cabin fuse panel.
All three fuses look good: unbroken
For the first test of the slow speed fans from the radiator thermoswitch have the key off.....Both fans should run in slow speed.
Passed test: both fans run slow
The second test is for the fast speed fans, key on, AC off.... Both fans should run in fast speed.
Passed test: both fans run fast
If the fans run in the tests above, then you should be good to go. No further tests are needed.
If you have been seeing high coolant temperatures and the fans have not been running, then you may need a new thermoswitch.
Golf IV / Jetta IV :: Low Coolant Light Has Been Coming On Often Lately
I got an 02 gti automatic. My low coolant light has been coming on often lately. I checked my coolant level and it was real low. I added coolant and the light didn't come back on. After a few weeks the light came back on. Again I had to add a lot of coolant..I have no leaks though. Where could all this coolant I add be going? I am not over heating or anything. Its like my car is literally drinking this and peeing it out, I have to add some almost every week now for the light to stay off.
View 24 RepliesGolf IV / Jetta IV :: Air Hose Coming Off The Top Of Airbox On VR6
This hose comes off the top of the air box next to the air intake and goes down towards the front of the engine. I need to know what this hoses called or what the part number is as mine is missing.
View 4 RepliesFord Excursion :: Drips Coming From Rear Axle Input Shaft Seal
I have noticed a few drips coming from the rear axle input shaft where the drive shaft connects. It has only done it once and there is no residue on the trailer hitch so I know it didn't dump everything on the road. If change this seal, how difficult is it and do you have any information which might make it easier.
View 14 RepliesGolf IV / Jetta IV :: Roaring Noise Coming From The Front
I hear a roaring noise coming from the front of my 2003 Jetta. I know it needs some kind of front end work, but I am not sure what. The front passenger side tire also wore badly and prematurely on the inside and outside.
View 8 RepliesGolf IV / Jetta IV :: Temp Going Up / Smoke Coming Out From Rear Of Car
I own a 03 mk4 jetta 2.0 I revved her up to 5000 rpm coming onto traffic. Drove about a mile or so when I noticed the temp going up. Pulled over and checked all my fluid levels and looked under for any leaks. Got back in the car turned it on and saw temp was normal again. I drove not even a quarter of a mile when I saw smoke coming out the rear of the car. Let the gas pedal go and when I did that the car started downshifting. Its an automatic. When it got down to the last gear the battery, check engine light, and epc light came on and car cut off. Cruised until I could stop somewhere safe on neutral. When I completely stopped I tried cranking but no crank. When I turn the key, lights and everything is good. Just no crank.
View 1 RepliesGolf IV / Jetta IV :: Smoke Coming From Radiator Fans
I don't understand what is going on I noticed smoke coming from my fans radiator fans and I'm pretty sure that it was motor being fried I've gone to the junkyard and bought a used assembly hooked it up and still nothing could be a possibility that when the motor fried it fried the control module for the fans
View 1 Replies