Ford 6.0L Power Stroke Diesel :: 2003 F350 - Drive Shaft Noise / Rear Pinion Seal Is Leaking
I was getting ready to replace the carrier bearing and noticed the rear pinion seal is leaking. Before attempting the replacement myself, I would like some opinions on the noise in the video below. Is this normal? I am confidant I can replace the carrier bearing and pinion seal, but not sure I have the tools for anything else.
YouTube ...
Ford Super Duty (1999-2016) :: 2004 F250 - Drive Shaft Removal To Grease The Center Spline
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesFord 6.0L Power Stroke Diesel :: 4x4 Drive Shaft Is Preventing HFCM Removal?
I've pulled the fuel lines and disconnected all the electric plugs. I don't seem to be able to remove the unit as the 4x4 drive shaft is in preventing me from full removal. Is this possible? Do I have to remove the drive shaft? Very frustrating as this should have been a 15 minute or less job. A video would be useful, but all my searches show only two wheel drive removal.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2011 - Drive Shaft Making Clicking Noise?
My buddy has a 2011 250 and is having some weird issues with a clicking noise. It started out when you put the truck in gear (D or R) and touch the gas it would click. Seems to be coming from the middle to rear part of the truck. Now it clicks when he's driving. This all started after he got 35's and a leveling kit. It's taller springs in the front and added a block in the rear. It has less than 15k on it.
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2000 - Front Drive Shaft And Axle Locked In?
I am a new 6.7 owner and had/ have a 7.3 As I have been getting to know the truck I have been under it and noticed that the front drive shaft and axle are locked in. My hubs are switched to auto but I know on my 2000 7.3 when my hubs are on auto my front axle and driveshaft are disengaged... I'm wondering if the new 4x4 system is different. I know that can save on MPG
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2006 F350 - Clunking When Go From Drive To Reverse And Now With Drive Too
So I have a 06 350 and I'm getting clunking from drive to reverse and now with drive too, I know my rear diff is on it's last days but I am wondering if that could cause the clunking and now my truck around 90km shakes likes crazy and same thing wana know if that's the diff. And if I was to fix diff myself would it not just be easier for me to just swap axles if I wanted to be cheap??
View 12 RepliesFord 7.3L Power Stroke (1999-2003) :: Rear Drive Shaft U-Joint Replacement
What Spicer Part #s for the rear u-joints would be? I'm not nailing down the right one. I keep finding numerous ones, 1410, 1350, 5-160....
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Loss Of Coolant When Pulled Heavy Load
Loss of coolant! I have a 2003 6.0 diesel with 200,000 miles. I put in a new oil cooler and ipr egr delete two years ago also flush the system and added a coolant filter. I filed it back up with the red antifreeze. Now the problem I have never lost any coolant since then and my deltas are about 5 degrees. But the other day I pulled a heavy load the first one since I did the repairs (coolant got up to 220 degrees and would drop back down) when I got home the coolant tank was about a inch low. I let the truck sit about 3 hours and checked it again and it was back at the full mark. Drove it the next day and it's back low about a inch, Any clue what's going on.
View 3 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Broken Shaft At 47000 Miles?
Just got a look at my 03' 6.0 turbo at Ford dealer. Truck still had boost but a real bad noise that was hard to describe. Pulled codes but no turbo code like the last turbo's. All the vanes were fine & no rust on the unison ring BUT the turbo shaft was broken. 3rd turbo went at 13,700 miles in July 2005 & now have 47,700 miles. I know I should drive it more but at 75 & having sold my boat it does't get driven to much.
I use Stanadyne with every tank full & drive it hard at least once every week to give the turo a workout. Use only Motorcraft oil every 3500 miles. Broken shaft on turbo would move about a 1/4 " on one end & a 1/2" on the other end. Ford service said they have seen shafts break before but said it was nothing I did to cause it.
Ford 6.0L Power Stroke Diesel :: 2003 F250 - Turbo Shaft Broken
Having a turbo shaft that broke? My 03 F250 turbo shaft was just replaced by the dealer, actually the whole turbo. This is the 4th turbo. Truck has 48000 miles on it. 1st 3 turbo's had sticking unison ring & vanes but this one had a broken shaft. Mechanic said unison ring & vanes were fine.
View 4 RepliesFord 6.7L Power Stroke Diesel :: Oil Pan Threads Pulled Out
Went to do my first oil change last night. Removed the horribly over tightened oil filter with out issue. We to pull the drain plug out of the oil pan and could not get to budge. Got a bigger breaker bar and got it out. Plug came out with about half the threads of the pan stuck in the bolt threads. Bolt must have been tongued to 100+ foot pounds. Got a new oil pan on order with dealer think i will have to cover cost since i was doing my own oil change.
Truck is a 2016 f250 6.7L.....
Ford 7.3L Power Stroke (1999-2003) :: 2002 F350 Truck Stars But Won't Drive
I have a 2002 f350 7.3. It was running fine 2 days ago. After I put some diesel in it my water in fuel light came on. I drained the water out and took all the fuel out and put fresh diesel in it. It starts up fine and idles okay but when I try to drive it it looses all power and acts like it's starving for fuel and almost dies. It was smoking white smoke for a little bit even after I took all the water out but now it's black. What it could be.
View 9 RepliesGolf IV / Jetta IV :: CV Spline Shaft Not Coming Out Of Hub
Any good way of getting the spline shaft out of the hub? I got the big axle nut off ok.
Normally the CV then just pulls out (inside unbolted, lower control arms (3 bolts) out). This one not moving if air chisel, 5lb sledge hammer.
NEVER had a rusted one (90% of my cars are Audi, not VW).
Do I have to remove the entire hub (including take the strut out) and put on hydraulic press?
Ford 6.0L Power Stroke Diesel :: Gear Oil Started To Leak When Pulled The Axle Out
So I replaced ball joints and hub bearings on driver side of the truck today ( passenger side tomorrow). Problem is when I pulled the axle out gear oil started to leak from axle housing not a lot but a leak nonetheless. Is this normal or did I break something.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 F350 - High Idle / Over Drive Light Started Blinking
OK, truck is 2000 F350. I am heading on a 2000 mile roadtrip to Yellowstone for my wife's 40th birthday in two days. What was our rock of a vehicle is now causing me severe anxiety.
Over the last few days the truck has been difficult to start - almost stops turning over as if the batteries were low. So I ignored it because if I plug it in, it starts fine and if I drive it and it gets hot - it starts fine.
Tonight while driving - I noticed a high idle and then it went to normal - I thought it was weird and a few miles later at a stop sign it struggled at idle, sort of loping but not romping very high and the over drive light started blinking. When I got home when I went from drive to neutral it goes to high idle and then the overdrive light blinks. The first time it blinked it went off when I pressed the OD button - but now it continues to blink.
Would low batteries be the root cause of this? I will continue my search for blinking OD light but I thought I would get this in the queue in case this is bigger than I can handle. I have 48 hours to resolve this issue - leaving Wednesday early morning.
Ford 6.7L Power Stroke Diesel :: 2011 F350 - Passenger Side Map Light Considerably Dimmer Than Drive Side
I purchased a 2011 350 crew cab lariat 6.7 diesel last week. That night i noticed that the passenger side map light was considerably dimmer than the drive side. Had to go back to the dealership 2 days later anyways to get a second key made. Showed the tech the light and he gave me 2 new bulbs to replace both lights with. Both were great for about a week but i noticed the passenger side has once again become dim....
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - No Power On Cold Start
I recently bought an 03 F350. I've noticed on cold starts that it has no power. After about 5 minutes it runs very well. I have not noticed any misfires or smoke and there are no codes thrown. Based on what I have read here, I assumed it was a FICM issue. I just got done testing it and it was at a solid 48v with 1 dip to 46 on engine crank. I'm baffled at this point. The truck literally has no other issues except low power for the first 5 minutes.
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 - Brake Controller Has No Power
I noticed the aftermarket controller in my 03 F350 is not working. I am wondering where the fuse(s) might be located. Under the hood? Are they fuses or relays?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2003 F350 Will Not Start
I have a early build 2003 f350 6.0. It will not start. Readings are good. ficm 48 to 48.5, synced, icp volts .30, icp climbs above 1200 psi, bat 13 to 13.5, ipr 14.8 to 40, fuel pressure 82 psi during crank..... will not start. Last week tore it down and replaced the tube of the hpop, found a leak in map hose and cleaned the turbo (vanes, ring). Ran ok for a week... shut it off and my sons baseball practice and will not start.... towed it back 2 days ago and nothing..... just cranks... I am at a loss. Another question would be where do i air test the hpo system on this truck.... ICP and IPR are in the back of the motor and hard to get to. I have read there is a way to do it under the valve covers.... not sure.
View 14 Replies