Ford Excursion :: P0720 Code - Output Shaft Speed Sensor
Okay, I have a P0720 code. I bought the Output Shaft Speed Sensor and read that it is on the back end of the transmission.
Need to confirm that it is on top of the transmission, near the tail end? Why are parts that go bad always in the most inconvenient places?
Accent LC (2000-05) :: Code For Output Shaft Speed Sensor - Transmission Rebuild
I had a rebuild done on my 2002 Accent. My question is now we get a code for the output shaft speed sensor. Would this have been replaced as part of the transmission rebuild?
View 2 RepliesFord Excursion :: Stall Out At Almost Every Stop Light / Code P0720 - Output Shaft Speed Sensor?
I just replaced my starter and on my first ride after replacing it the X started to stumble a bit, and then would stall out at almost every stop light. It threw a CE light and I pulled the code P0720. I searched here and it seems most guys say this is a C.O.P. issue. If it is a bad C.O.P. would it stall like that?
I did have the battery disconnected but I made sure the terminals were clean and tight. Is this a coincidence or did I do something while changing the starter?
Ford Transmission :: 1998 F250 - Code P0720 For Output Speed Sensor Circuit - No Reverse
I bought late 98 F-250, 5.4 G, 4WD. OHad to replace the steering flange because they messed up the ignition cylinder and flange. Truck didn't run for 4 years. 249K miles, no history available. Got the engine running, no DTCs. D, 3, 2, 1 barely moved the truck forward but, R hauled butt in reverse. Checked transmission fluid it was good and clean.
Came back to it a few days later it threw a P0720 (output speed sensor circuit) and I have no reverse, park feels like it wants to move, R is neutral, N is forward, D is forward, 3 is forward, 2 is forward, 1 is forward. The N is full drive. I cleared the P0720 code after it came up and it has not returned. The instrument gauges work but the odometer display is intermittent. Linkage? Fluid? Sensor? Wires?
Santa FE SM (2001-06) :: 2004 - CEL Code P0720 / Bad Output Sensor
My hyundai 2004 sta fe awd 3.5 LX engine light came on while cruising dwn the freeway. At the same same time i heard a loud thud and speed went down from 65 to 40mph and a high idle. I drove it home and hook up the obd2 scanner and got P0720 suggesting bad output sensor. So I decided to buy new sensor from the dealership, put it in and thought it will fix the problem. After few days the engine light came on (P0720)again with the same clunk noise and speed down from 65 to to 40 mph at high rpm. Took it home, did some experiment by putting back the old sensor. I Connected the harness back, but this time I wrap the female connector with the electrical rubber tape and electrical vinyl tape. Problem fixed. No more engine light,transmission shift smoothly. I think the connector (harness side) to the output sensor was crack that's why its not making good solid connection. The rubber tape technique held the female connector pins tightly together. New part didn't do anything but it was a learning experience.
View 1 RepliesGolf IV / Jetta IV :: How To Replace Vehicle Speed Sensor (VSS)
2002 Jetta 2.0L...
The Haynes Manual tells you to lift the car up and un-mount the engine mount on the drivers side of the transaxil to get access to the VSS underneath the vehicle, but you can do it from the top of the engine!
1. Take out your Air filter box for easier access
2. My VSS was covered by a metallic heat pouch with snaps. (not mentioned in Haynes Manual)
3. I got Needle nose pliers to wedge in the small area to unscrew the bottom half of the VSS. It is a small area to get your hand in, but with the needle pliers was actually pretty easy.
4. Then get something small enough to release the clip for the top plug. I used my screwdriver.
5. Screw in your new VSS and plug the top cable back, then put your air filter back in place.
If you look at the pictures I took, you can see the VSS and the silver pouch I mentioned. I had a lot of trouble finding the location of the VSS with no real good pictures or explanations online. Note these pictures were taken from the drivers side, which the empty space is where the air filter was and on the right you can see the battery.
Ford F-150 (2004-2008) :: Airbag Light Code 24 - Sensor Output Feed / Return Circuit Open
I have a 2007 f150 sport. I am getting a 24 code on the airbag light and I do know that is Sensor output feed/return circuit open. What I do not know is where is this sensor located and what could it mean if I am getting the code...
View 2 RepliesCelica :: Location Of Speed Sensor On 1991 Automatic 5th Generation
What is the location of the speed sensor on a 1991 automatic .. According to Haynes it is under the air filter but know matter how hard i look i cannot locate it .. Could it be that mine is an import from Japan so will have a different location ..
View 5 RepliesGolf IV / Jetta IV :: CEL Code For Bad Coolant Temp Sensor?
So my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 RepliesGolf IV / Jetta IV :: 2002 GLX V6 Misfiring When Cold - CEL With Cam Sensor Code
I just got this car it a 2002 jetta glx vr6 12v 5 spleed. It has a miss new plugs wires gas and used coil pack. It misses especially when cold check engine light on says cam sensor changed it and still same thing if I clear the code it comes right back.
View 1 RepliesGolf IV / Jetta IV :: Code P1340 - Cam / Crankshaft Sensor Out Of Sequence
So I started up my 12v VR6 the other morning and it sounded like a Subie. Threw the awful code P1340: cam/crankshaft sensor out of sequence, and took it to the shop. I'm being charged $1900 for servicing the timing chains, only. Doesn't include water pump and clutch like every other shop does. Reason for this is because in Montana, no one works on these cars. So I this is my only route. I had to choose this small euro repair shop or the VW dealer.
But, they just recently called me and told me I need to get the timing gears changed or whatever? They want to charge an additional $600 or so to do that. Are these gears a real problem? or are they just trying to F me. I mean, $1900 should make this car flawless as it is so I feel that they are attempting to rip me off even more.
Golf IV / Jetta IV :: MAF Sensor Fault Code - No Crank Or Start
I bought an 05 golf GL with a 2.0 and 5 speed in January for commuting to work.
Well, recently. I was on my way home from work, I'm an engine tech for Cummins Inc, and I notice my CEL came on and the car stalled multiple times at red lights. So I limped it home, connected my scanner and the fault was "Implausible signal from Mass Air Flow sensor". I cleared the fault code and tried to start the car. Nothing, no crank no start. Just an audible click from under the hood.
I disconnected the battery for 5 min reconnected it and it started fine. Drove it to work the next day, no issues. I tried to start it again and nothing, CEL was on again for the MAF sensor. I pop started it, car ran like hell, rough idle, low power, etc. luckily I have a dualy that I can drive in the mean time.
Golf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: Error Code P0113 - Intake Air Temp Sensor
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ...
Golf IV / Jetta IV :: 2001 - Code P0102 / Air Temp Sensor Circuit Was Low
2001 jetta 2.0 VW guys a while back I was pulling a code saying that the air temp sensor circuit was low I believe it was P0112 so I replaced the maf with a bwd maf. Said it was for the car. Was fine for a day but now it has a P0102 code and the epc stays on (rough idle) what could be wrong ? Is it because the car hasn't learned the new sensor yet because I've only drove 10km or do I have a faulty sensor. BTW replacing the maf fixed the P0112 code
View 5 RepliesGolf IV / Jetta IV :: Check Engine Light Is On For Code P0030 - O2 Sensor
I've been having an issue with my car and the check engine light is on.
The code reads : P0030
Heated oxygen sensor - bank 1 sensor 1
heater control circuit
2001 VW GTI VR6 ....
Golf IV / Jetta IV :: 2004 - Camshaft Position Sensor Error Code
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
Golf IV / Jetta IV :: Code 00281 - Replaced G68 Sensor But Still Only First Gear And Reverse Are Functional
I started my car the other day and found that it only drives the first gear and I can also put it in reverse. VCDS gave me a 00281 code saying no signal from Vehicle Speed Sensor G68. I replaced the sensor, but it still doesn't go into gear beyond 1st.
VCDS gives me the following codes after replacing G68.
2 Faults Found:
00652 - Gear Monitoring
27-10 - Implausible Signal - Intermittent
00281 - Vehicle Speed Sensor (G68)
03-00 - No Signal
I came across TSB 01-99-02 which says something about the codes being incorrect. It seemed a little vague about whether it is actually G38 or G22. I don't want to buy more sensors only to have it be something else. The speedometer and tach work fine so G22 doesn't seem likely to me.
The VCDS site says it could be several things including bad G68 or G38 sensor, low fluid & bad valve body. Was it the G38 sensor?
Golf IV / Jetta IV :: 2003 - Error Code P0113 / Intake Air Temp Sensor
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ....