Golf IV / Jetta IV :: Installed New Crank Position Sensor Now Car Will Not Start
After installing a new crank position sensor on my 05 GTI 1.8T would I have to recalibrate my ECM, my car will not start.
View 2 RepliesGolf IV / Jetta IV :: 5 Engine Fault Codes - Cam Position Sensor / Knock Sensor / Secondary Injection Pump And Mass Air Flow
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesGolf IV / Jetta IV :: O2 Fault Codes Came Back After Sensor Replaced
Keep getting o2 fault codes. Replaced sensors came back. tried another set of sensors came back. Checked wiring for breaks no luck. Replaced ecu still no luck. So going through wiring again and checking for continuity. Looking for a list of what pins to check for voltages, and what each should be from ecu to sensor connectors. Looking for what wire is signal and how to and what voltages to check for...
View 5 RepliesGolf IV / Jetta IV :: 2000 - Coolant Gone - Speedometer Fault Code Came On
This morning, I wanted to drive to work, but all of my coolant was gone. In the last couple of weeks, I had some errors with my speedometer and had it replaced a week ago, which did not fix my problem (the P0722 sometimes still came up).
Could it be that my coolant leaked over the last weeks and somehow messed with my speedometer, or are those most likely independent errors?
My car is a 2000 Jetta VR6 and at this point I don't want to put too much into it any more. If you need more input, let me know.
Golf IV / Jetta IV :: 1999 - Oil On Crank Position Sensor Making It Miss
99 2.0 jetta. Getting oil on crank position sensor making it miss. Is it the rear main seal? Only reason I can think to have oil around the flywheel... How hard is a rear main seal to change out....
View 2 RepliesGolf IV / Jetta IV :: Engine Will Turn But Not Fire / P0441 Fault Code And Gas Cap Warning Light
After running to operating temp, if the car is turned off then restarted (like you would at a gas station, which is where I notice this) the engine will turn and turn and turn but not fire. I have noticed that stomping on the acceleration will cough it into life during this procedure. This doesn't happen every time and I have recently run high octane gas during a long distance trip.
106K miles...
Recent p0441 fault codes and gas cap warning light...
No other problems or codes...
Golf V R32 :: 2008 Won't Start / Does Not Turn Over - Fault Code U0100
Fault code (U0100 lost comm with ECM/PCM)
Car started a few weeks back. I let is sit while I ordered a new dash, it had a blow dash airbag. I replaced the dash, taking out the stereo and instrument cluster. I also replaced the battery with a new factory one.
Went to start the car and nothing happened, no cranking, the only thing I can hear is a single click from the starter. All the lights are on in the instrument panel.
Windows, sunroof dont work even in AUX power
Fuel pump does not prime
I checked the fuses, none were blown, checked the relays, all work.
OBDII reader throws out the code U0100 even though check engine light is not on. I dont have VAGCOM or VCDS but should in a few days.
Golf IV / Jetta IV :: CEL Code For Bad Coolant Temp Sensor?
So my check engine light came on in my 04 jetta sw, and when I had the car read, it gave me a code that tracked down to be a bad coolant temp sensor. I bought the replacement part from my local VW dealership, installed it and the check engine light went away. Now about 2 weeks late it came back on, and I am getting a reading of "Coolant temp sensor high voltage". So it goes from needing replaced, then the replacement is running high voltage?
View 3 RepliesGolf IV / Jetta IV :: 2002 GLX V6 Misfiring When Cold - CEL With Cam Sensor Code
I just got this car it a 2002 jetta glx vr6 12v 5 spleed. It has a miss new plugs wires gas and used coil pack. It misses especially when cold check engine light on says cam sensor changed it and still same thing if I clear the code it comes right back.
View 1 RepliesGolf IV / Jetta IV :: Code P1340 - Cam / Crankshaft Sensor Out Of Sequence
So I started up my 12v VR6 the other morning and it sounded like a Subie. Threw the awful code P1340: cam/crankshaft sensor out of sequence, and took it to the shop. I'm being charged $1900 for servicing the timing chains, only. Doesn't include water pump and clutch like every other shop does. Reason for this is because in Montana, no one works on these cars. So I this is my only route. I had to choose this small euro repair shop or the VW dealer.
But, they just recently called me and told me I need to get the timing gears changed or whatever? They want to charge an additional $600 or so to do that. Are these gears a real problem? or are they just trying to F me. I mean, $1900 should make this car flawless as it is so I feel that they are attempting to rip me off even more.
Golf IV / Jetta IV :: Car Won't Start / Crank
04 Gli 1.8t 6 speed. When I go to start my car and turn the key nothing happens . No clicking no cranking nothing. All my lights work radio works everything. Would a bad starter cause this? I can jump my car and it works fine.
View 7 RepliesGolf IV / Jetta IV :: Car Neither Start Nor Crank
I am having trouble with my car not starting, when turning the key nothing happens. I have replaced the battery and have even tried to push the car and do a rolling start could not get it going. I am assuming that if i can't do a rolling start that rules out the starter, is that correct? I also verified all fuses and changed the fuel pump relay.
I am leaning towards an electrical problem (ground/short circuit). I have a Bentley manual and VCDS tool, how to diagnose the electrical problem and pinpoint the issue.
Golf IV / Jetta IV :: No Crank And Won't Start?
So I have a no crank no start. All other electrics appear to be working . For the most part I just hear a soft click when I try and start. Doesn't sound like your normal solenoid clicking. New starter, 12v at battery , new ignition switch. It did this to me last month , started taking the ignition out then just only started before I could even get the new part in.
Changed it anyway. Seem to fix it. My next step is going to be to check the ground under the battery. Which I checked and cleaned up a little bit about eight months ago. After that I'll try and jump the starter and check the voltage going to the solenoid. I check the fuses last month when it did it to me and they all seem to be okay.
Golf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: Error Code P0113 - Intake Air Temp Sensor
My 2003 Mk 4 Golf have had a lot of error codes and I have cleared most (O2 sensors, thermostat, and Mass Air Sensor) I now have an error P0113 which is the Intake Air temp Sensor.
So I need to clean the sensor first then maybe replace it, but I can't find the sensor on the intake manifold.
I have looked all through the U-Tube info, but nothing matches my 2003 Golf 2.0L ...
Golf IV / Jetta IV :: 2001 - Code P0102 / Air Temp Sensor Circuit Was Low
2001 jetta 2.0 VW guys a while back I was pulling a code saying that the air temp sensor circuit was low I believe it was P0112 so I replaced the maf with a bwd maf. Said it was for the car. Was fine for a day but now it has a P0102 code and the epc stays on (rough idle) what could be wrong ? Is it because the car hasn't learned the new sensor yet because I've only drove 10km or do I have a faulty sensor. BTW replacing the maf fixed the P0112 code
View 5 RepliesGolf IV / Jetta IV :: Check Engine Light Is On For Code P0030 - O2 Sensor
I've been having an issue with my car and the check engine light is on.
The code reads : P0030
Heated oxygen sensor - bank 1 sensor 1
heater control circuit
2001 VW GTI VR6 ....
Golf IV / Jetta IV :: 2004 - Camshaft Position Sensor Error Code
I have a 2004 MK4 Golf 2.0l that's been throwing a CPS error code. My brother was going to come down to visit for a weekend. He had done some diagnostic work and had me order a timing kit and a camshaft position sensor from ECS.
So, with my assembled parts, I brought the car in to a reputable shop. Anyway, the guy does the work and now the car is ready and saying that the CPS took nearly 4 hours more of work.
Golf IV / Jetta IV :: Automatic Shifting - Code P0722 Output Speed Sensor
I just recently purchased my first mk4 golf 2.0 after having a mk3 jetta vr6 for two years. I've been having problems with the car shifting (automatic) i put a code reader on it and came up with p0722 output speed sensor which explains why it sometimes shifts at 4500. My two questions are where is the output speed sensor located? and what is a normal shifting range for properly running automatics?
View 2 Replies