Golf IV / Jetta IV :: 2001 - Throwing Codes For Misfire / O2 Sensor?
So my girlfriends's 2001 2.0 Golf (engine code AVH, 153k miles) began throwing codes for misfire on cylinder 4 and for the o2 sensor (post-cat) recently. I went ahead and replaced the spark plugs, wireset, and the coil pack. They were way overdue. The CEL went away for like 30 miles, and then came back. Now it's reading misfire on cylinder 3 and the same thing for the o2 sensor. What else it could be? Search is coming up blank, most people replaced the coil pack and the CEL went away.
View 2 RepliesGolf IV / Jetta IV :: CEL On With Camshaft Position Sensor Code And Misfire On Cylinder 3
She is a 1999.5 Golf 2.0 (although, she just has a rabbit symbol on the hatch, is she a Rabbit or did someone remove the Golf badge?) I just bought the car, with less than 160,000 miles. The dome lights work sometimes, Door Ding works intermittently as well, but sometimes will "glitch" in other words it will be making the sound but it kind of stutters? Odd? The horn sometimes works, however it is very silent? Check engine light is on with a camshaft position sensor code and miss on cylinder 3. Someone told me to replace the "109 relay"... could this be the problem or is this the CCM?
View 5 RepliesGolf IV / Jetta IV :: 2001 - Misfire On Cylinder 4
New to the VW world but I am not out of my element for I am a Porsche guy. So I feel right at home. Last night I picked up a 2001 wolfy Jetta with a 1.8t on the cheap with a misfire on cylinder 4.
I have verified I have no spark on 4. I have confirmed the issue is not the spark plug, coil pack by swap and see method. My coil pack and plug work fine on another cylinder. I reset my cels and here are the new ones that pop up:
a 121 - gas pedal position sensor- doubt this would give me a no spark
a 304- Misfire on 4, (duh, like I needed to hear that)
a 030- bank one 02 -Doubt this would also give me a no spark condition)
In my testing:
I have good system voltage on the coil pack
I have good ground ohms
My signal wire is not shorted high or low
When I take V and ohm readings on the coil pack connection, either with the ign on or off they are all in line with the other sensors. So I don't think I have a wire issue.
The PO had the ECU replaced at a local dealer. I looked at the old ECU and it appears it had got wet at one point.
Im wondering if the same thing hasn't happened to the new one. however after they replaced the ECU they gave him the car back still broken. So it never ran even with the new ECU.
1 Where is the ECU?
2 What tells the ECU to fire the coil packs at the right time?
Golf IV / Jetta IV :: 2001 1.8T - Cylinder Misfire Code
I recently changed my spark plugs + coil packs in my 01 1.8T because it read a couple cylinder misfire codes. Drove it for a few days out of curiosity plugged the code reader in again and it's still reading misfire codes. What could the issue be still?
View 6 RepliesMitsubishi - Mirage :: 1998 - CEL Codes For Fuel Trim Bank / Oxygen Sensor Bank 1 Sensor 2 And Cylinder 1 Misfire
I own a 1998 Mitsubishi Mirage with about 190,000 miles on it. The engine light has started coming on and I get three codes:
P0170 Fuel Trim Bank 1P0136 Oxygen Sensor Bank 1 Sensor 2P0301 Cylinder 1 misfire
Read more: [URL] ....
Golf IV / Jetta IV :: 2001 - Misfire After Replacing Coolant Temperature Sensor
I drive a 2001 Jetta with the 2.8 v6 with ~125k miles
So for a while my car was giving me a false read on my temperature so I replaced the sensor. I actually followed instructions from a thread on this site. [URL] ....
Now when I go to drive my car, it runs sluggish and misfires if I really give it some gas. CEL is on(however does not return a code when hooked to a computer), and flashes when gassed hard.
I've checked to make sure spark plug wires were reconnected correctly and securely. No leaking has occurred from the temp sensor. shift rod drive unit is reconnected correctly.
Elantra XD (2001-06) :: Random Misfire On Cylinder 2 / 3 And EVAP Codes
Trying to troubleshoot my 2001 Elantra (173k). I'm having intermittent trouble codes being set and I'm wondering if they may be related:
P0302
P0303
P0446
The cylinder 2 and 3 misfires are relatively recent. Plugs and wires are visually ok (and not that old). I swapped plugs 1 and 4 with 2 and 3 to see if the plugs are bad. It took 3-4 days, but the P0303 set again (and it's very intermittent - car will noticeably lose power for a few seconds, code set, then run fine for several days). I also sprayed carb cleaner on the intake manifold gasket with no change in engine idle, so the gasket appears to be intact.
I had read in a forum somewhere that the misfires could be related to a vacuum leak, which could also be setting the P0446 code. I removed the charcoal canister and inspected the lines - visually ok.
I bench-tested the canister control valve and it did operate, though I noticed some charcoal blocking the valve so it would not close all the way when energized. I used compressed air to blow the debris out of the valve and it appears to close properly now.
I went to hmaservice.com and noticed there are no instructions for the P0446 DTC. I've been using a Haynes manual instead. For quite some time now when refueling, the fuel nozzle shuts off every few seconds (I have to slowly put the fuel in to avoid).
Some questions:
- Can these codes be related?
- Based on my symptoms, should I replace the canister control valve? What about the charcoal canister and the charcoal air filter - should those be replaced as well?
- What else should I check?
Ford F-150 - 1997-2003 :: 2001 - Codes Pops Up - Cylinder 1 Misfire?
2001 f 150 5.4 liter with it being code pops up saying cylinder one misfire, I've charge coil and spark plug ran great for awhile now starting to act up again. Got coil check and says still good and look at spark plug and looks still in good shape being just replace two weeks ago. It's running fine but if it sits over night and I get in and start it and begins to shake when I but it in drive and don't even need to move the truck just place it in drive with foot on break. I drive it awhile and it stops and runs fine?
View 9 RepliesOldsmobile - Alero :: 2001 - Mass Air Flow Sensor Or Cylinder Misfire
2001 Olds Alero. i'm getting a P0300 reading, Cylinder misfire, and i was told a could months ago my mass air flow sensor was out of range. are they related? how serious is a misfire? can i drive a couple hundred miles before service?
View 2 RepliesGolf IV R32 :: Cylinder 5 Misfire Codes P0300 And P0305
So i got two codes.... P0300 and P0305. I am thinking its the coilpacks because i changed the spark plugs a few months ago. Cleared it last week and came back today. What else could it be? And is it ok to just change one coil pack or do i have to do all of them? The recall was done in 2007.
View 3 RepliesGolf IV / Jetta IV :: 5 Engine Fault Codes - Cam Position Sensor / Knock Sensor / Secondary Injection Pump And Mass Air Flow
I recently picked up a 2000 jetta vr6 for a very good price its a glx I have owned a vr6 before and done timing chains myself on it this one is a glx , I am having 5 fault engine codes on my vagcom they are cam position sensor , knock sensor, secondary injection pump, and mass air flow it ran fine 100 miles yesterday this morning the epc came on then went off and ran bad can these codes all be related or do I have to replace each sensor individually..
View 9 RepliesGolf VI R :: Engine Error Codes - Random / Multiple Cylinder Misfire Detected
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
Golf IV / Jetta IV :: Misfire Cylinder 1 And 5 On VR6
Getting misfires on cylinder 1 and 5 in my 2001 Jetta GLX. Replaced coil pack. Installed a different/used cam position sensor.
Swapped injector 1 and 5 with 2 and 6. Cleaned MAF and throttle body and did adaptation. Checked resistance of plug wires and swapped plug positions.
Golf IV / Jetta IV :: Cylinder 1 / 3 And 5 Misfire
[URL] ....
View 6 RepliesGolf IV / Jetta IV :: Misfire On Cylinder 1 At Idle
Alright Ive had a misfire on cylinder 1 for far too long. I've replaced all ignition coils and plugs with oem parts. Also replaced fuel pump and filter with oem. As well as 2 injectors. Before I would misfire under load, now I misfire at idle..wiring looks good and not cracked from what I can see. Only codes I reciece are random multiple misfire, misfire cylinder 1. And diverter valve mis function because of my BOV. So what do I do now vortex?
View 1 RepliesGolf IV / Jetta IV :: 2003 VW - Misfire On Cylinder 2
So I've been having some problems with my 2003 Volkswagen Golf lately (2.0 L gasoline engine, 98k miles). It started with an engine coolant thermostat code. This was repaired by replacing the thermostat and housing. Shortly after this fix I began to get a misfire, especially on rainy and humid days. Checking other forums I discovered that this was probably the result of a bad ignition coil.
The coil, spark plug wires and plugs were all replaced, but I am still getting a misfire. The idle is very rough so I've heard that it could be a bad fuel injector or faulty ground (though with the new components the other three cylinders sound cherry). The next step would be to purchase a "noid" test light and determine if the electronics to the injector are bad. I've also read that it could be a vacuum problem. There is a smell of unburned fuel when the engine is running.
How was it repaired? I'm quite good with the mechanical parts but lack the diagnostic tools, vacuum testers, multimeter and other such devices for performing complete screenings of the vehicle. Also, I can't drive it out to the local auto parts store to read the new error codes anymore. Finally I've got a "Chilton's" for the car but if there is a better manual available (better pictures, more descriptive instructions).
Golf IV / Jetta IV :: Code P0304 On Mk4 2.0 AEG - Misfire On Cylinder 4
2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 RepliesGolf IV / Jetta IV :: VR6 Misfire On Cylinder 4 - Low Compression Level Of 90
I am a new vr6 owner. I just purchased mine not to long ago. It seems to have developed a pretty mean misfire on Cylinder #4. It is also showing a low compression level of 90 on cylinder #4. all my other cylinders show somewhere between 105-110. I replaced my wires and my coilpack. It did not improve anything, infact, my car seems to run worse now. I am baffled as to what can be causing my misfire.
View 7 RepliesGolf IV / Jetta IV :: Cylinder 2 And 3 Misfire - Code P0411
Alright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage