Golf IV / Jetta IV :: VR6 - Random Multiple / Cylinder Misfire
Replaced my water pump March 2nd using the "From Below" method. Started the car after and the check engine light was on and water pump was no longer leaking. I drove the GTI to Advance (15 Mins away) it drove fine and I pulled two codes.
P0300 - Random Multiple/Cylinder Misfire
P0301 - Cylinder 1 Misfire
The car pulled and drove normally. The next day the car is misfiring badly. Hesitation and bucks when accelerating until roughly 3k then smooths out.
I will swap my coilpacks and check if the misfire moves as soon as I can get my hands on an OBD2 Scan Tool.
From what I understand about the VR6 :
-The water pump runs off the serpentine belt
-Camshaft timing is controlled by the timing chain.
-Timing chain is not affected by the serpentine belt/pulleys.
Questions :
-Can turning the Crankshaft Pulley affect timing?
-Can that be the cause of the misfire?
24V VR6
Golf IV / Jetta IV :: 1995 - Random Multiple Cylinder Misfire?
I have a 1999.5 Jetta VR6 12v, last week the car would not start. After some tests I determined the coil pack had gone bad. Replaced the Coil with a brand New aftermarket German made coil. Now 1 week later, driving at highway speed CEL came on, started to flash and obviously misfiring again. Ran Codes and now im getting these DTC's:
1)random multiple cylinder misfire detected p0300
2) cylinder 4 misfire detected p0304
3) ignition coil output 3 electric malfunction p1395
4) cylinder 3 misfire detected p0303
has this new coil gone bad already after a week?
New issue?
Plugs were replaced less than a year ago, wires were apparently replaced by previous owner about 2 years ago now. Crank sensor replaced less than a week ago...
Golf IV / Jetta IV :: 2000 - Cylinder 2 Misfire And Engine Sputter
2000 GTI GLS 2.0L ... I understand I need to replace the Ignition Coil Pack on my car. I have looked on ECS Tuning to find the coil pack, but from all the pictures I see of other people coil packs they look nothing like what mine do. So I'm wondering if they are different for my specific car? So the issue that I have is my engine sputters sometimes, but more so when is wet outside. Its only cylinder 2 misfiring currently, and I replaced my Fuel Filter and Fuel Pump already in the past 4 or 5 months. Also a local shop had done some work recently and I know they had replaced the spark plugs. So I'm just wondering what coil packs I need for my car, and how I would go about replacing them. From what I saw online with other 2.0L (They weren't GTIs tho) was that the coild pack was behind the SIA pump or something like that, and they are a small black box. It looks to me that my coil packs are inline above the spark plugs and cylinders?
View 2 RepliesGolf IV / Jetta IV :: 2000 - Cylinder 2 Misfire / Pending Code P0302
2000 Jetta 2.0 cylinder 2 misfire. Replaced plugs and wires. No check engine light but code is pending and there's still a misfire. Need to smog
Replace coil pack?
Swap fuel injectors and recheck?
Golf VI R :: Random / Intermittent Misfire On Cylinder 4 After 5000 RPMs
I was running in a track day at Sebring today and missed a shift. Rookie move...the car eventually went into limp mode. I took the car back to the pits and scanned the codes. Limp mode was confirmed in addition to a cylinder 4 misfire and a random/intermittent misfire. Cleared the codes and went back out; couldn't even finish the lap before the car was thrown back into limp mode.
I was able to hobble home by keeping the car out of boost and started trouble shooting. So far I have ruled out spark plugs and coils. Should I be looking at the injector next? Any chance I bent a valve? The misfire can be triggered by putting the car under a load and bringing it up to 5,000 RPMs or higher.
Golf VI R :: Engine Error Codes - Random / Multiple Cylinder Misfire Detected
I recently found these codes. My car is APR 1+. The car seems to run fine so I'm not sure what is going on. I changed the plugs at ~60K miles and now have 72K miles.
Address 01: Engine (CRZ) Labels: 06F-907-115-CDL.clb
Part No SW: 5K0 907 115 M HW: 8P0 907 115 B
Component: 2.0l R4/4V TFSI 0020
Revision: 5BH20--- Serial number:
Coding: 0403010A180F0160
[Code] ....
Golf IV R32 :: CEL Start To Blink Then Stay On - Random / Multiple Cylinder Misfire Detected
I was driving the car normal with no problem. Got to a red light stop an as I was coming out of the red light the car started to hesitate a bit. So I start to drive home as I was driving home my check engine start to blink and then it stay on. When I got home and park the car I shut off ,then start it up again then the check engine light was off but the hesitation was still there. Then I got my computer and got the vagcom and got this code :
16684-random/multiple cylinder misfire detected
P0300-008- implausible signal
Golf IV / Jetta IV :: Misfire At Random Times Most Often At WOT
I have a 01 wolfsburg jetta with aw engine code .. I have replaced and gaped spark plugs all 4 coils , DV. As well as fuel filter . Sometimes it runs fine . It misfire at random times most often at WOT. ..and I've noticed almost always when fuel level is low.. installed a boost gauge .. after disconnecting battery to reset ecu it boosts 10psi and runs strong .. however 1 or 2 WOT and it will misfire and then I won't boost over 4-5 PSI .. worst of all I get no CEL not even blinking .. I have also located a leak in the brake booster line . Does this affect it at all? ..
View 2 RepliesGolf IV / Jetta IV :: No Start - Random Misfire / Stalling And Bad MPG
Well first the exact car I have. 99.5 Jetta 2.0 AEG. It all started with one loud backfire with a stall at a stop light while in neutral. After that it was random stalling and jerking while driving. So I checked my everything and all seemed well. I replaced spark plugs because they where fouled and nasty. Cables are good. They're near new and tested them with a multimeter. Next I checked my injectors and they are surprisingly very clean.
I had also ran seafoam prior to these problems a few weeks before it all started. Next step was new fuel filter. Old one was nasty and black stuff dripped out. That didn't work. So I checked for vacuum leaks with throttle body cleaner. Nothing. Visually threre is nothing wrong under the hood. So today I changed the fuel pump. Went for a test drive all seemed well. Can out of the bank. Then it won't start. So I wait like normally. And it normally gets me home. Nothing. Will sometimes start but if I'm not holding the gas it dies. I don't know what to do. My only other thing I can think of is the coil pack.
Golf IV / Jetta IV :: Misfire Cylinder 1 And 5 On VR6
Getting misfires on cylinder 1 and 5 in my 2001 Jetta GLX. Replaced coil pack. Installed a different/used cam position sensor.
Swapped injector 1 and 5 with 2 and 6. Cleaned MAF and throttle body and did adaptation. Checked resistance of plug wires and swapped plug positions.
Golf IV / Jetta IV :: Cylinder 1 / 3 And 5 Misfire
[URL] ....
View 6 RepliesGolf IV / Jetta IV :: Codes For Random Misfire And Small EVAP Leak Detected
Okay, so a few weeks ago, my tire blew out on the freeway. Of course my spare wasn't in there and when I got one I couldn't get the lugs loosened. My 4way was too big on all sides. It was late, I am a single mother of two young kids so I had no choice but to drive slowly to get it off the freeway. The next morning I came back fully prepared, got my car in to get a new tire. I have been driving with ONE code for my CEL, but at the shop (where I use to work) I used the scanner and it threw 5 codes.
P0300 Random misfire
P0442 Small EVAP leak detected (this one was already there)
P0420 Catalyst system below threshold bank 1
P0301 Misfire cyl 1
P0303 Misfire cyl 3
My beautiful love is an 02 Jetta 2.0 4 Cyl. Now, since 4 of these codes popped up AFTER my first blowout (I turn 30 next month, knock on wood)
Did driving my car at 5 mph about a mile and a half (everywhere up until the gas station was NO PARKING) do something to my car? All of a sudden, any in town driving ESP IDLING makes my check engine light blink and my car has no power I just have to pull over wherever I am. I checked the car out myself on the side of the road and my cat was glowing. After this I do not drive my car.
So, what should I do. I did a tune up. Should I replace the 02 sensors then the cat?
Golf IV / Jetta IV :: Misfire On Cylinder 1 At Idle
Alright Ive had a misfire on cylinder 1 for far too long. I've replaced all ignition coils and plugs with oem parts. Also replaced fuel pump and filter with oem. As well as 2 injectors. Before I would misfire under load, now I misfire at idle..wiring looks good and not cracked from what I can see. Only codes I reciece are random multiple misfire, misfire cylinder 1. And diverter valve mis function because of my BOV. So what do I do now vortex?
View 1 RepliesGolf IV / Jetta IV :: 2001 - Misfire On Cylinder 4
New to the VW world but I am not out of my element for I am a Porsche guy. So I feel right at home. Last night I picked up a 2001 wolfy Jetta with a 1.8t on the cheap with a misfire on cylinder 4.
I have verified I have no spark on 4. I have confirmed the issue is not the spark plug, coil pack by swap and see method. My coil pack and plug work fine on another cylinder. I reset my cels and here are the new ones that pop up:
a 121 - gas pedal position sensor- doubt this would give me a no spark
a 304- Misfire on 4, (duh, like I needed to hear that)
a 030- bank one 02 -Doubt this would also give me a no spark condition)
In my testing:
I have good system voltage on the coil pack
I have good ground ohms
My signal wire is not shorted high or low
When I take V and ohm readings on the coil pack connection, either with the ign on or off they are all in line with the other sensors. So I don't think I have a wire issue.
The PO had the ECU replaced at a local dealer. I looked at the old ECU and it appears it had got wet at one point.
Im wondering if the same thing hasn't happened to the new one. however after they replaced the ECU they gave him the car back still broken. So it never ran even with the new ECU.
1 Where is the ECU?
2 What tells the ECU to fire the coil packs at the right time?
Golf IV / Jetta IV :: 2003 VW - Misfire On Cylinder 2
So I've been having some problems with my 2003 Volkswagen Golf lately (2.0 L gasoline engine, 98k miles). It started with an engine coolant thermostat code. This was repaired by replacing the thermostat and housing. Shortly after this fix I began to get a misfire, especially on rainy and humid days. Checking other forums I discovered that this was probably the result of a bad ignition coil.
The coil, spark plug wires and plugs were all replaced, but I am still getting a misfire. The idle is very rough so I've heard that it could be a bad fuel injector or faulty ground (though with the new components the other three cylinders sound cherry). The next step would be to purchase a "noid" test light and determine if the electronics to the injector are bad. I've also read that it could be a vacuum problem. There is a smell of unburned fuel when the engine is running.
How was it repaired? I'm quite good with the mechanical parts but lack the diagnostic tools, vacuum testers, multimeter and other such devices for performing complete screenings of the vehicle. Also, I can't drive it out to the local auto parts store to read the new error codes anymore. Finally I've got a "Chilton's" for the car but if there is a better manual available (better pictures, more descriptive instructions).
Golf IV / Jetta IV :: 2004 1.8t 6speed - CEL Keep Flashing Code P0501 / Random Misfire On Cylinders
I have a 2004 Jetta 1.8t 6speed, I recently bought it from a person(my first VW ever) so just trying to fix some things on it, One thing that I'm stuck at is My CEL, it keeps flashing the code P0501 and some random misfire on my cylinders, I have reset it and they keep coming back.
when I put about 10-15% throttle it revs up fine, no misfire or hesitation until the fuel gets cut off around 5500, which is 1k below factory red line, does not hit a thing like the rev limiter where it pegs off the top multiple times just fuel cuts off.
If i put anything above the said pressure the car then begins to misfire and lots of hesitation and that's what causes those codes to go off.
I've been reading many things pointing towards the engine speed sensor or the wiring. Occasionally my fuel/temp gauge quit working but I believe that is a separate issue all together.
So really trying to narrow down what is actually causing my engine to hesitate at low rpm.
Also i might note when I'm in neutral I can go wide open throttle and the car revs fine until the cutoff and only does the bog down when it's under full load. It sorta feels like the possible misfire is due to bad air/fuel but really do not know.
Golf IV / Jetta IV :: Code P0304 On Mk4 2.0 AEG - Misfire On Cylinder 4
2000 Jetta GL 2.0 AEG. I am receiving the P0304 which I have identified as Cylinder misfire #4. I read on some previous posts that I cannot be the distributor because if it was I would be receiving misfires on two cylinders. The spark plugs are OEM NGK and have been replaced recently.
View 2 RepliesGolf IV / Jetta IV :: VR6 Misfire On Cylinder 4 - Low Compression Level Of 90
I am a new vr6 owner. I just purchased mine not to long ago. It seems to have developed a pretty mean misfire on Cylinder #4. It is also showing a low compression level of 90 on cylinder #4. all my other cylinders show somewhere between 105-110. I replaced my wires and my coilpack. It did not improve anything, infact, my car seems to run worse now. I am baffled as to what can be causing my misfire.
View 7 RepliesGolf IV / Jetta IV :: Cylinder 2 And 3 Misfire - Code P0411
Alright so my car is popping up 4 codes.
P0411 - Secondary Air Injection System Incorrect Flow Detected
P0300 - Random/Multiple Cylinder Misfire Detected
P0302 - Cylinder 2 Misfire Detected
P0303 - Cylinder 3 Misfire Detected
Vehicle: 1999.5 VW Jetta MK4 2.0L GLS (AEG)
The P0411 code I have had for a while now and I been lacking to fix it. I pretty sure I can get this fixed but it doesn't cause problems so I haven't paid to much attention to it. Anyways, the other day I noticed a puddle of coolant under my car so after checking it out, the water pump was leaking so I bought a new one and replaced the old one. However, during the replacement process I had to remove the timing belt and I accidentally turned the top pulley about 1 notch and didn't notice at the time. After putting everything back on, I turned my car on and the engine sound a bit weak so I ran for about 10 minutes around a couple blocks.
I instantly noticed that the car had no power and it took me a long time to speed up. When I got back, I plugged in my scanner and I only had the same P0411 code and nothing else. After carefully reviewing the camera I had recording during the water pump replacement, I notice I had turned the top pulley a bit so I went ahead and removed the timing belt, readjusted it, and it worked! I was excited that the car was working fine again. Soon after, I headed out to take a drive and noticed after 60MPH the car didn't have much power. The car still accelerates after 60MPH, but extremely slow. As soon as I arrived back home, I plugged in my scanner and that is where I seen the 4 codes. Now my question is what could have caused this? Could I have damaged something when I ran my car with the incorrect timing?
Things I have done so far:
-I checked to see if I left anything unplugged.
-I checked for any vacuum leaks
-I checked my oxygen sensors so see if I was running rich/lean
Things I will do after work today:
-Check the spark plugs
-Check spark plug cable for damage