Golf IV / Jetta IV :: 2004 - Have To Hold The Shifter Until Clutch Is Engaged For 3rd Gear Position
I picked up a 2004 GTI not long ago for pretty cheap because it had a few issues. I am working my way through them. However, having 3rd gear issue.
All other gears are perfectly fine but there is way less play in the shifter in the 3rd gear position and I have to hold the shifter in position until the clutch is engaged (pedal up) to avoid the gear grinding. Once the clutch is engaged it stays in 3rd gear fine. It doesn't matter if I am moving from 2nd to 3rd or 4th to 3rd. Same deal. I have aligned the shifter several times using to proper procedures with no effect.
It never grinds 3rd with the clutch disengaged (so the synchro is fine?) and it will bang shift no problem. Oh and the clutch is less than a year old. It was installed by a shop before I bought the car. It's not really a big deal, but I would like to fix it. If I have to swap the trans that's fine, but need to figure out if it is a trans or linkage issue first.
Golf IV / Jetta IV :: 1998 - Clutch Engages Lower To The Floor / Shifter Stuck In Gear
98 Jetta TDI hydraulic system ... We just received this vehicle from my mother in law, who is not driving any more. It's a cream puff--79,000 miles, beautiful condition. Problem is the clutch engages lower and lower to the floor, and eventually the shifter gets stuck in gear. The brake pedal slowly sinks to the floor when at stops on hills. Our mechanic tells us these two are connected because both the clutch and brake run off the same hydraulic system.
1st time he said the fluid was filthy, and he emptied the system and put in clean fluid. Worked for a little while and then we were back where we started. Second time he replaced a couple parts on the clutch, replaced this fluid, and this time it ran like a dream for a little over a month. Then the problem just returned. Again he says the fluid is filthy, and now we are looking at replacing the master cylinder and again changing the fluid. The theory behind why this is happening is that my mother in law let the car sit for half a year before passing it on to us. She didn't do much driving the 6 months before that either. I've done research, and this doesn't appear to be a common problem by any means on these cars.
Golf IV R32 :: How To Attach Shifter Knob To Stalk
The only serious problem i can't quite figure out is how to attach the shifter "knob" to the stalk. I see how the stock knob is attached, but i will be using an aluminium rod so clamping wont be a great idea. I have thought of removing the stalk and drilling a set of holes through it and running bolts to hold them together, but it isn't that big of a diameter and also i don't like the though of one of those nuts coming loose and messing up my shifting. My nest idea was epoxy, but I still would like to remove it if perhaps one day i wanted to. So there's my dilemma.
View 2 RepliesFord Aerostar :: 1995 - Sloppy And Loose Shifter?
My mom's 95 shifter is slowly getting worse. Right now it's at the point where we have to hunt for gears just to put it into park or reverse or d/od. It's not stiff like the rest of ours, hers is all sloppy and loose. She says it's been doing this for a while, but i think it got worse when i pulled her cluster out to change the light bulbs. I say this because i couldn't get the needle cable un done, so i just let the cluster rest on it while i was changing the bulbs, which put a little bit of tension on it.
View 14 RepliesFord Excursion :: 2002 - Sloppy Shifter Lever
I've been experiencing the ever so popular sloppy shifter lever in my 02 excursion. So naturally I started prowling around the site looking for answers to my issues. I have ensured both of the torx bolts are present and tight at the end of the shift tube on the bracket that connects to the shifter cable and have replaced the shift tube (It was worn out) and it worked great but has not completely fixed the issue so today I crawled underneath the truck to try and adjust the shift cable and have found that the detent in the shift linkage from the gear position sensor that runs to the shift mechanism (not sure what it's called) that is inside the transmission is really nonexistent, it is effortless to move it from P to R but from R to N is good and stiff like it should be but from N to D and D to 2 is effortless. I have zero experience with what creates the detent inside of the transmission and looking for a link or pictures or write up something that I can look over and attempt to educate myself on before I dive in to this blind....
View 14 RepliesFord F-150 - 1997-2003 :: Shifter Not Going Into Park - Linkage Sloppy
Having trouble with shifter not going into park. The linkage is sloppy. Is there a bushing kit or something to tighten up the linkage?
View 3 RepliesFord F-150 - 1997-2003 :: 1998 - Column Shifter Loose And Sloppy?
98 f150 4x4 5.4... So i purchased this truck about 3 months ago and now I am having problems putting it in Park. The column shifter is very loose and sloppy. Is there any way to rebuild this?
View 3 RepliesFord Aerostar :: 1986 - Shifter Is Sloppy / Often Hard To Find 4th When Downshifting From 5th
I have an '86 Aerostar with the 2.3 four and 5-speed stick. The shifter is sloppy, and it's often hard to find 4th when downshifting from 5th, and sometimes, it shifts hard through all the gears. Other times, it works fine. The manual says that this shifter was used from 86 to 89 only. Did they use the same one on Rangers? Can I buy a rebuild kit? Or, is this a sign of some other problem such as the clutch slave cylinder?
View 1 RepliesLexus IS 2014+ :: 2015 - Shifter Knob Seems Loose
I have a 2015 is350 f sport. I don't know if this is normal, but my shift knob is very loose. I can literally take my thumb and pointer finger and turn it either way with almost any pressure. When I turn it, the leather seems to be attached, and turns with the shifter when I turn it to the right to tighten it.
View 13 RepliesPrius (Gen 3) :: Noise Near Shifter Knob Occur Only At Freeway Speeds
I have a 2010 Prius no frills model with 5500 miles on it. I've started hearing a noise that sounds like loud burst of radio static. I hear it with the radio off or on. It's very intermittent, but seems to occur only at freeway speeds. Seems to be coming from underneath the shifter or underneath the dash in the same area.
View 2 RepliesSubaru - Legacy :: 1995 LS Not Starting - Knob On The Shifter Won't Go In To Get Out Of Park
Ok. I replace my alternator on my 1995 Subaru Legacy Ls. Everything went great. Last thing I did was to connect the positive cable on the battery. When I did it sparked alittle. Well when I got into the car to start it nothing. Turn the key nothing. The knob on the shifter won't go in to get out of park. Neighbor checked my battery said it was fine. But nothing will come on. Nothing.No lights. I had problems with my ignition before. Do you think my ignition went out? Honestly don't know what to think. Some one told me that these cars have a secondary security system. If it goes on you cannot move the knob on the shifter and when you turn the key on nothing?
View 2 RepliesGolf IV / Jetta IV :: Shifter Won't Go Into Any Gears
Okay, my shifter rod got spun, and now it doesn't want to go into any gears. Just freely kinda swirls, and you can't push down. The guy working on the car wants to pull the shift box down and see what is going on. He thinks the shift cable or selector cable is broke.
View 5 RepliesGolf IV / Jetta IV :: Shifter Would Not Go Into Any Gear
The issue with the car is that the tranny won't go into any gear. With clutch in or out. I had very little play left or right or up and down. Not sure what could be wrong. The car has 120k miles and no mods.
View 2 RepliesGolf IV / Jetta IV :: 12v VR6 Intake Shifter Rod Noise Won't Go Away
I recently noticed a rattling coming from my intake manifold and with little research I discovered it was the intake shifter rod. I ordered the new updated bushings and installed them today and the rod continues to rattle just as bad. My car only has 90k and I am unsure what to do to fix the noise. I am hesitant to order a whole new shifter rod because it could be the manifold itself too worn. I am just curious if there is anything that I may have overlooked or if there is anything I can do.
View 4 RepliesGolf IV / Jetta IV :: Installing Short Shifter?
There is only one DIY i can find that is still alive. I have a megan short shifter. Its already half way in. I just don't have any instructions and i am kind of at a loss as to where i go from here. Does this shifter change the way my reverse gear will be engaged? I mean will i need to pull the trigger up to go in reverse or will i still push down? Does the spring that came with the kit go under the sleeve or above it? Sounds confusing.
View 3 RepliesGolf IV / Jetta IV :: Wobbling Of Shifter While In Gear
I have the 20th anniversary GTI with the 6-speed manual at 90k miles
I have the Dieselgeek Short shifter installed so for the most part my shifter is nice and tight/precise. However, I have some play in the shifter while it is in gear and I understand that this is normal for a car as it ages. But I assumed that the Dieselgeek would've solved all the gear slop in my shifter, and I was wrong.
So is there a part I can replace to tighten it back up?
Golf IV / Jetta IV :: Hard To Get Shifter Into Gear
When the car is in gear it's great! Or at least it seems great. However, trying to place the Shift Lever in the car into the gear "slots?" is troublesome.
It feels as though there is a wall in the way for each gear, and i have to force my way through the wall. It's not absolutely Terrible, for i've been driving like this for months. But i want a smother shift! I want to be able to just slide the Shift Lever into gear without any hangups or major resistance.
Double Clutching seems to work, however it might just be from the small loss of RPMs through the process of double clutching.
Personally I would rather not have to double clutch just to see a slight improvement. I have big feet and they constantly are rubbing on the floor mat as well as the plastic above the pedals, so double clutching always feels like i'm wedging my foot into a hole, then back out and in, before i can go into another gear lol.
The problem is only a real issue when i'm in higher RPMs giving the car more gas. I.E. after a fast launch in first, shifting even around 5500 puts a WALL up on second gear making it impossible for me to get it into second gear, after not getting it into second i usually throw it in third, and essentially lose all the acceleration i had from the first gear launch.
As well is there anyway to make the clutch a little stiffer? She grabs fine, i just like stiffer clutch, it requires less of me trying to wedge my huge foot on the pedal.
It's an un-molested MKIV Jetta VR6 with 167k.
Golf IV / Jetta IV :: Shifter Pops Out Of 3rd Gear When Let Off The Gas
My problem is that it pops out of 3rd gear when I let off the gas. I have had this problem before so any tips on setting my shifter linkage?
View 5 RepliesGolf IV / Jetta IV :: 03 - Shifter Stopped Engaging 1st Or 2nd Gear
My03 GLI will not engage first or second gear.
This morning, i was having some issues getting the car in reverse, but it eventually engaged and is fine now. I drove to the barbershop, and on the way home, the shifter stopped engaging 1st or 2nd gear. it moves freely into position (TOO FREELY) and all other gears will engage. common sense tells me that the clutch is fine and the problem is with the shifter.