Ford Wiring/Electrical :: 1999 - Wipers Only Works When Off?
I have a 99 f450 and the wipers work when not on. it's this an electrical issue or a bad wiper motor.
View 2 RepliesFord Wiring/Electrical :: 1988 F150 - Speedometer Not Working
I got my first truck today and it's a 1988 Ford F-150 and it runs great! The only issue is that the speedometer doesn't work and I won't be able to register it until it does. I was wondering what I can try out to maybe fix the issue and if not, how I would replace it. Every other gauge works, it's just the speedometer that isn't. The needle doesn't move at all it just sits at a 0 all the time.
View 8 RepliesFord Wiring/Electrical :: 1991 F150 4x4 - Speedometer Not Working?
I have been trying everything to get my speedo working on my Ford. It didn't work for 3 months after I got it then I decided to put some gear oil on the cable. This made it work for about 200 miles then it would only work with the clutch in and then not at all. I've replaced the speed sensor(not one on rear end the thing the cable goes into), and the gear that goes on the end of it. If I hook a drill up to the cable the tach moves. Could the cable be stretched or just needs some speedo cable lube?
View 5 RepliesFord Wiring/Electrical :: Speedometer And Cruise Control Not Working / Fuse 18 Keeps Blowing
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 RepliesFord Wiring/Electrical :: 2000 - Electric Shift Transfer Case Wiring Diagram?
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
Ford Wiring/Electrical :: Right Front Turn Signal Light Works But Hazard Doesn't
1994 Econoline E350. All the other lights work but on the front right the turn signal light flashes but the Hazard lite will not flash. I check for power at the wire at the light and there is none.
View 6 RepliesFord Wiring/Electrical :: 1995 - Speedometer Not Working / Transmission Shifting Hard And OD Light Blinking
I recently purchased a 1995 F150 4x4 with the 351 Windsor. Upon driving it I realized the speedo didn't work, transmission shifted hard,and OD light blinking. After googling my issue I found out it was the VSS. I climbed under the truck to find out the VSS isn't even plugged in. I searched for the wire but could not find it, only a spliced cable.....
View 4 RepliesJeep - Speedometer - Electrical-wiring - Liberty :: Warning Lights Started To Flicker On And Off When Headlights Turned On
While driving I turned on my headlights and my car became possessed. My warning lights started to flicker on and off, my car was dinging out of control. The speedometer, gas, and RPM gauge went to zero. My brights light would not come on. My dinging for the lights being left on, or the key being left in the ignition, after the car is parked, and the door is open, will not go on either. I turned my lights off and all was well. Turned them on again and the same thing happened.
Now, the following day, it is doing this periodically every couple of minutes while I'm driving, whether the lights are on or not. My radio and head lights work fine. I checked all my fuses and they all seem to be AOK. I disconnected my car battery and reconnected it to see if it would reset and it still did the same thing. One other strange occurrence. The last month or so while I've been driving my battery light came on for a few minutes. I had the battery checked and it is not bad. Then last week my gas-cap warning started to randomly appear. I changed my gas cap, and guess what.....it still came on, at random.
Ford Wiring/Electrical :: 2000 - Airbags Deployed - Reset?
2000 E150 - I see a pair of airbags listed at a salvage yard with module. Do I need the module? Do the "switches" that set off the airbags reset?
View 3 RepliesFord Wiring/Electrical :: 2000 F350 - Steering Wheel Lights Are Out
My steering wheel lights r out and need to know which wire runs power to those. also the led in my headlight switch is very dim.I checked the wiring and all the wires check out with high 11's and high 12 volts.i checked the volts at the led in the switch and it read 2.18 v.i have another light switch from the salvage yard and the same thing. which wire powers that light. also, the light only comes on when the key is in the on position or back for accessory. if i just turn the lights on it wont lite, only with key in ignition in those positions. truck is a 2000 f350 xlt dually.....
View 14 RepliesFord Wiring/Electrical :: 2000 - No Keyless Entry - Won't Go Into Programming Mode?
Have already fixed the weak lock motors on my 2000 F250. Now I can't get the truck to go into programming mode. I know it has Keyless entry, as I located the relays and identified the wiring while trying to fix the weak locks before I found the fix here.
I've tried the key on off 8 times but the locks never cycle. I've tried it with the driver door open and closed, cycling the locks from unlocked to locked to unlocked before cycling the ignition switch. Tried cycling the ign switch 5 times, 8 times and 10 times.
Ford Wiring/Electrical :: 2000 - Power Door Lock Not Working?
I have a 2000 f250 super duty. Right now the only problems with it are:
1: When i press the door lock switch the passenger door lock will click and come down about half way but the door still is unlocked. in order to lock it, you have to press the latch down by hand.
2: My key won't unlock or lock the driver's side door from the outside, however it works to start the truck and open the passenger door.
3: When i bought the truck the previous owner game me a handheld wireless unlock and lock button. The little black thing with an alarm button, and it doesn't work either, i replaced the batteries and still nothing. So what would be the solution to fixing all of this?
Ford Wiring/Electrical :: 2000 F150 - Power Cuts Out When Attempting To Start
2000 XLT F150 4.6 - New starter & solenoid(s), battery cable & fuse links good.
When i turn the key, I hear one single click and the power cuts out entirely. I can't attempt a second start or turn on the lights or have any power going through the truck until I disconnect the battery for about 10 seconds then reconnect. Electrical becomes live again, then when the ignition is turned the electrical cuts out again. I do hear a single cluck at the starter (probably attempting to engage when it cuts out) and a clunk right at the inside fuse box (drivers side).
Ford Wiring/Electrical :: 2000 - Clicking Coming From #2 Relay Switch Under The Dash
In an attempt to bleed my drivers side caliper today I noticed clicking coming from the #2 relay switch under the dash. The clicking stopped once I pulled out the relay. I continued to bleed my caliper which I've been having issues doing so. It was kinda odd how I was able to bleed the caliper after pulling the relay. Is it possible that the [email protected] system could be causing issues with the pcm? 2000 f 150 4.2 v6 232,000 miles .....
View 9 RepliesFord Wiring/Electrical :: 2000 F350 - Alternator Died / Isolator Failed
Over the weekend I was driving my 2000 F350 and the alternator died (found out later). The shop said they replaced the alternator but it wasn't charging. They later told me it was because the isolator failed. My 2nd battery WAS a yellow gel battery. Before the battery (in series) was an 50 amp circuit breaker...........that blew apart.........and the battery had a melted off side terminal. It looked like the 'sealed gel battery" had been 'leaking for a while" (as there was funky acid type white corrosion deposits in a few places. Any speculation what happened here?
View 4 RepliesFord Wiring/Electrical :: 2000 F250 V10 Starter Engages When Truck Is Put Into Reverse
2002 Ford F250 V10 Auto... When I put the transmission into reverse, the starter kicks in...
View 8 RepliesFord Wiring/Electrical :: 2000 - Interior Lights Won't Illuminate From Door Opening Or Headlight Switch?
I have a 2000 E150 (Glavel Conversion) van and the interior lights do not illuminate when the doors are opened, although they used to. They also no longer turn on from the headlight dimmer switch. They will turn on individually if the manual switch at each light is pressed while the engine is running, so the bulbs and wiring appear to be working. I replaced the headlight switch with no noticeable effect. Is there a timing circuit that switches these on for a short period of time to allow illuminated entry that could have failed? If so, where would I find the module and how would I test? Relays and fuses look good.
View 1 RepliesFord Wiring/Electrical :: 2000 F250 - Dash / Parking And Tail Running Lights Not Working
I have a 2000 Ford F250 lariat 7.3 .... This vehicle has an aftermarket double din stereo pillar gauges for Pyro meter and transmission temp and has also had a snowplow attached but since re moved since I purchased it. It also has H ID headlights, which are run by the passenger side headlight connection.
The problem I'm having is that whenever I turn on the parking lights it is blowing the number eight fuse under the hood. Which is giving me no dash lights running lights parking lights or taillights. Initially the fuse would last for a few minutes and then burn out. I should also add that the trailer wiring harness doesn't work either and the driver side headlight will work sporadically.
Ford Wiring/Electrical :: 2000 F150 - Hooking Power Door Lock To Command Start?
I am trying to hook up my power door locks to my command start. I am having trouble getting it to work. Ive tried a number of relay diagrams from the12volt.com. I've tried actuators/reverse polarity and it blows both my factory door lock fuse and the fuse I have supplied to the relays. Ive also tried 5 wire alternating 12 volt positive door locks, and 3 wire positive door lock combinations. Both of these combinations the relays click back and forth fine with the actuators unhooked, when I connect the actuators the doors unlock with the factory switch but when I unlock with my remote it blows the fuse. How to properly connect the actuators?
View 3 Replies