Ford Wiring/Electrical :: Transfer Case Shift Relay Module Location
Where it is located in a 97 F150 XLT Automatic with the ESOF?
Transfer Case Shift Relay Module
If it goes bad, would it be possible to still select 4L just no 4H?
Ford Wiring/Electrical :: 2002 - Complete Headlight Switch Wiring Diagram?
Any COMPLETE headlight switch wiring diagram? Everything I find online only shows 2-3 wires in each sub connector, nothing with all wires and colors, and what they do. and of course the factory service manuals no longer work on my new computer. the switch and associated wires went up in smoke 2 hours ago, and this truck is my only means of transportation rite now. what i need is headlight wiring with colors so i can temporary hook up a toggle switch to have lights until the new switch and connectors come in next week. I went to pull the switch and connectors out of the parts truck, but of course that does not have fog lights so it uses different switch and connections.
View 14 RepliesFord Wiring/Electrical :: 2004 - Instrument Cluster Wiring Diagram?
Looking for a source for a wiring diagram for the 2003/4 f350 instrument cluster, specifically the wiring/connectors to the gauges? A link to a PDF file would be nice. I would like to try and disconnect the PCM control to the transmission temperature and engine temperature and drive the gauges from my own sensors to bypass the non-linear behavior that ford decided was in our best interest. I am NOT interested in installing any more gauges, just want to control the ones already present with my own signals. It is possible that these gauges are all addressable devices on a common bus, instead of individual controls.
View 8 RepliesFord Wiring/Electrical :: 1987 F150 - Wiring Diagram With Carburetor?
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 RepliesFord Wiring/Electrical :: Different Color Wires In Cab - Brake Light Not Working - Wiring Diagram?
Need a wire diagram. I have a connector in the cab that has red,blue,lt green,white wires. It's causing my brake lights not to work. I need a wire diagram that shows were they go. I can't find these wires in my Haynes manual.
View 3 RepliesFord Wiring/Electrical :: 1999 F250 - Door Courtesy Light Wiring Diagram
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 RepliesFord Wiring/Electrical :: Power Mirror Wiring Diagram?
I'm trying to find the wiring diagram for the power windows in a 96 f150. I've got a set of these that i need to fab a harnes for to install in my 82.
View 12 RepliesFord Wiring/Electrical :: 2012 E350 - Wiring Diagram?
Where can I find/buy a wiring schematic for a 2012 Ford E350 with the 5.4 L V8?
View 1 RepliesFord Fuel System :: Electric Choke Wiring Diagram?
I have a newly remanufactured Holley 1835 carb which has had an electric choke added to it. My '59 F-100 has the original electrical system in place. Where would you recommend running the positive and negative wires from the choke? No instructions came with the carb.
View 8 RepliesFord Super Duty (1999-2016) :: Electric Wiring Diagram To Stop Turn LED Bar?
Just got an inexpensive LED Stop/Turn/Taillight Bar my problem is it has (3) wires Red, Black and White while the available connection from the old bar has only (2) wires Black and White with Red Dots.
The wiring instructions for the new LED bar says (1) Attach black wire to tail lamp circuit(+), (2) Attach the Red wire to the stop/turn circuit(+) and (3) Attach white wire to a good ground(-) location.
How I should hook this up? My thought is Black to Black , Red to White with Red Dots and White to Frame metal.
Ford Wiring/Electrical :: Wire Diagram Doesn't Match OEM Plug
Only numbers 1,2,5 match the diagram below. my 6,7,8 are BK/W, PK/B, BR/PK. My Sony CD player came with bare wires. So I could cut off the truck oem plug. How hard is it to find a plug that goes from my OEM plug to my Sony CD player?
View 10 RepliesFord Excursion :: 2001 - Tranny Fuse Blowing - Electrical Malfunction - Wiring Diagram?
I posted earlier about the tranny in my 01 Ex v10 having a transmission problem. The show looked at it and found the O2 sensor had shorted out and in some way sending the truck in to limp home causing the tranny fuse to blow????
Any way they fixed it or so they said and I drove it for a few hours and it did fine. The next morning I drove it and it blew the fuse. (under hood box I belive #19) I took it back to the shop and they beat and banged on it....got it wet etc. and can not get it to do it again. I know whe have an electrical issue but what all runs off of the fuse that controlls the tranny?
Is there any online wiring diagrams of excursions or superduty drive trains? Where all to look for the problem?
Ford Wiring/Electrical :: 1967 - Installation Of External Electric Fuel Pump?
I have a fuel pump I want to install I want to hook this thing up on a switch inside the cabin to be used as kind of a security device, but I am hoping I can wire it into the ignition as well.... I want the pump to activate when the ignition is turned on but only if the (hidden from view) switch is in the "on" position. Not sure if all this is possible.
I have heard I ought to utilize a relay to avoid voltage loss at the pump. I have never hooked up a relay to anything before although I have heard of them being used. This system is being installed on a 1967 F250.
Ford - Explorer :: 2003 - Transfer Case Diagram
I bought a new to me 03 explorer 4.6 tow package XLT 136000mi. Rebuilt aamco trans with 10k on it. Been checking it over before i put it on the road.. No 4x4 but the button lites work and i got into low range once. (Had a hell of a time getting back to high but eventually it did). Question is if there is 12v at the brown wire on the TC the case should be fully locked? I figure when i check it if there is not 12v at the brown wire in 4x4 high i could apply 12v directly with a jumper wire to see if the case locks to 4x4. Am I correct?
View 2 RepliesFord F-150 - 1997-2003 :: 2000 - Key Less Entry Wiring Diagram?
I am trying to add a keyless entry to the already equip, power door locks but am having problems figuring the wiring schematic
View 8 RepliesFord Excursion :: 2000 V10 - Fuel Pump Wiring Diagram
Looking for a link to the fuel pump wiring for a 2000 V10 Ex? I'm trying to pinpoint my no start issue and want to make sure I don't miss anything. I think it goes from 20 amp fuse under hood to inertia switch to relay under hood to pump? 20 amp fuse has power but at the inertia switch I have no voltage, just approx 35 ohms resistance to ground on both outside wires. Does the inertia switch close a ground or should it have voltage?
View 10 RepliesElectrical-wiring - Batteries - Cadillac - Deville :: Car Randomly Losing 100% Electric Power
Was driving one day, and when I came to a stop sign, the car just died.. I couldn't start it up, so I pushed it to the side of the road.. I tried to turn the key again, and it fired right up... No issues for about a week, but then I came outside one morning, and the car was completely dead. No interior lights, dash wouldn't light up, nothing. (no cranking noise when you try to turn the key) I assumed it was because the battery was old, and the car had just been sitting there for about a week without being started up. I was about to give it a jump, but when I opened the door, the lights came on. I put the key in the ignition, the dash lit up, and the car fired right up.. No issues for about a week, until again, came outside, car was completely dead..
I used my other car to run up to the store, and when I came back, decided I would try to start up the DeVille again. Randomly, upon opening the door, the cabin lights lit up, and sure enough, car fired right up... no one had touched the car while I was gone.. I drove the car up to a shop near my house, where they tested the battery, which tested good. Terminals are all clean, and he made note that the ground connection to the car was also firm and clean. He offered to run a diagnostic the following Tuesday for $125. I returned home, drove the car once more over the weekend, but when I went to start the car Monday, it was again, completely dead. It's been over a week now, and I haven't been fortunate enough to get it to start. I again tried this morning in hopes that I would get lucky, but it's still completely dead.
Ford Wiring/Electrical :: 1967 F100 - Instrument Cluster Gauge Wiring
I am a beginner when it comes to anything involving wiring. I am looking to re-wire all of the wiring coming off of the instrument cluster gauges. Once I have completed all of the wiring on the gauges, I may feel confident to move onto something else. As of rite now, it appears as though my truck is still running on all of the original wiring, and over the past few weeks, I have been having many wiring related issues. I found a schematic that includes the wiring for the gauges that I am going to go off of. I have a couple of questions before I begin.
1.) On the schematic, it shows connectors such as "Connector G" which is moving all of the gauges wires to there locations. Do I need to use a specific Ford connector, or could I purchase a new connector at any hardware store that carries them? As far as I am concerned, connectors do the same thing as all other connectors. (Let you connect and disconnect for easy instrument cluster removal.)
2.) I am not looking to purchase one of those expensive wiring harnesses. I would like to just purchase some wire that I can cut / use myself. What brand / type of wire should I be looking to purchase? I do not care if it is striped / colored as I will use wire tabs to name / label each wire.
Other than that, I feel confident enough to attempt something such as this. Here is the wiring schematic I am going to use.....
Ford Wiring/Electrical :: Moving Engine And Ignition System - Wiring Harness For Further Use?
I plan on moving the engine/drivetrain from my 1986 F350 460 to my 1996 F250. I also want to move over the 1986's ignition system with a Duraspark 2 setup.
Although I could just cut in the easiest places to remove the wiring for later reuse I am looking for where to make the cuts, what to take and what to scrap. Alternatively I am also asking if there are aftermarket or OEM replacement sets out there are aren't a ton of money. The current harness in the 1986 has been sprayed with engine oil and cooked for 27 years so I am looking at alternative options if there are any.