Ford Wiring/Electrical :: 2000 - Electric Shift Transfer Case Wiring Diagram?
I am curious if it is possible to make a stand alone controller for the electric shift transfer case in a 2000 F-350?
The reason I ask is, this is swapped into a 4x4 conversion in a van and I would like the transfer case to work like the factory, but I don't want to swap over the whole GEM module. I have the high to low and low to high shift relays and wiring, the selector switch from the dash.
I know that powering up the relays will shift the transfer case, but the GEM module tells when the relays need to shut off, and that is where I am not sure what to do. I am assuming that the other plug on the shift motor (6 pin plug) is the sensor that tells the GEM module where the shift is at.
What needs to be done (with a bank of relays).....
Ford Super Duty (1999-2016) :: Electric Wiring Diagram To Stop Turn LED Bar?
Just got an inexpensive LED Stop/Turn/Taillight Bar my problem is it has (3) wires Red, Black and White while the available connection from the old bar has only (2) wires Black and White with Red Dots.
The wiring instructions for the new LED bar says (1) Attach black wire to tail lamp circuit(+), (2) Attach the Red wire to the stop/turn circuit(+) and (3) Attach white wire to a good ground(-) location.
How I should hook this up? My thought is Black to Black , Red to White with Red Dots and White to Frame metal.
Ford Fuel System :: Edelbrock Choke Not Setting?
The choke is never setting. Something in my throttle linkage is wrong or sticky and it doesn't flip up the lever that engages the choke?
Hard to explain. Hopefully, the video makes it clear?
[URL]
Ford Fuel System :: Gasket Blew Out On The Choke
The gasket blew out on the choke (tube) plate on my 460. The one that sits on the engine with the tubes running up to the choke.
Do I need to apply a gasket sealer when I replace it or does it just go on dry? I've read some conflicting opinions on it. A tad on the corners to hold it in place. Put it on dry or put sealer on it.
I know when I remove it I will be able to tell but since I don't have any hi temp sealant. I'd rather buy some when I get the gasket than go back.
Explorer :: 94 Ford - Wiring Diagram For AC System
I am in need of the wiring diagram for the A/C sys. I'm getting fire to the low pressure switch-but then no further.
View 6 RepliesFord Fuel System :: 1972 - Run The Carb With Choke Permanently Open?
So I picked up a 2 barrel carburetor of a 1972 Ford Truck, most likely an F250. Has a tag and everything, this is a Motorcraft 2100-D (D2TF JB). No electric choke or anything like that. So I'm wondering if I can run the carb with choke permanently open? Also is there an electric choke conversion that I can buy, if so where is it? I can't seem to find one. Also what are the adjustments? I seem to have 2 needle valves to adjust and one other.
View 10 RepliesFord Fuel System :: 2100 Choke Vacuum Control Frozen?
I picked up a renamed 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. Are these parts still produced and if not is there another way to make it work?
View 10 RepliesFord Fuel System :: Holley 4150 Choke - High Idle After Restarting?
I bought a new Holley 600 CFM 4150 with electric choke for my 79 ford F 250 with 400 engine. If I start the truck cold the choke works as it should and after driving 10 or so minutes it runs fine off choke. When I restart the truck after stopping for gas or food it goes back on high idle even with the engine temp at 180 degrees. Should it go on high idle even on a hot day fully warmed up every time i start it? I don't remember my last 600 doing it.
View 3 RepliesFord Audio/Video System :: 2003 F250 - Wiring Diagram
Where I can get a radio wiring diagram for 2003 F250 Crew Cab?
View 1 RepliesFord Fuel System :: 2100 Choke Vacuum Control On The Back Of Carb Is Frozen
I picked up a remaned 2100 for my '72 and I found out choke vacuum control on the back of the carb is frozen. I can't find anyone who carries it, let alone knows what it is. Are these parts still produced and if not is there another way to make it work?
View 13 RepliesFord Fuel System :: Choke Plate Does Not Close When Turn On Ignition And Depress The Accelerator
I am having problems with my automatic choke. Holley 80457. When I turn on the ignition and depress the accelerator, the choke plate does not close. It is wired and has vacuum.
View 1 RepliesFord Excursion :: 2000 V10 - Fuel Pump Wiring Diagram
Looking for a link to the fuel pump wiring for a 2000 V10 Ex? I'm trying to pinpoint my no start issue and want to make sure I don't miss anything. I think it goes from 20 amp fuse under hood to inertia switch to relay under hood to pump? 20 amp fuse has power but at the inertia switch I have no voltage, just approx 35 ohms resistance to ground on both outside wires. Does the inertia switch close a ground or should it have voltage?
View 10 RepliesFord - Explorer :: 1994 - Wiring Diagram For Fuel Injector?
I'm in desperate need of a wiring diagram for a 1994 explorer fuel injector wiring diagram. I am working on why my injectors are not working ( another thread) and I now need this to back trace all the wires in this loop.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: F250 - Starting System Wiring Diagram?
I have a new to me 1999 F250 with the 7.3 engine. The previous owner installed a push button start to get around the ignition actuator being broke. Over the weekend I pulled the column and replaced the actuator but the truck will still not start with the key; with the push button it starts just fine. I'm not getting any power on the starter relay signal wire, so I suspect something in between the key and starter relay. I searched around a bit, but could not find a wiring diagram for a 1999 diesel super duty.
View 3 RepliesFord Ranger / B-Series :: 2003 3.0 2WD Auto - Fuel Pump Wiring Diagram?
I'm working on a truck for a friend's mother and all of the tests that I've done point to the fuel pump. However, to make sure the pump is getting voltage past the large connector block under the cab, I would like to do a pin-out test before I pull the tank (or the bed). The pump will not run/prime in KOEO test, the relay is good, as are all of the fuses and the inertia switch.
Looking for a wiring diagram handy for this purpose? I've look all over this forum and searched quite extensively and I haven't found one for this year. Since it isn't my truck, I don't feel like purchasing a manual. I'm working on a 2003 3.0 2WD Auto.
If a wiring diagram isn't available, what colors are the wires going to the fuel pump? That way I can at least test the ground and the positive.
Ford Wiring/Electrical :: 1967 - Installation Of External Electric Fuel Pump?
I have a fuel pump I want to install I want to hook this thing up on a switch inside the cabin to be used as kind of a security device, but I am hoping I can wire it into the ignition as well.... I want the pump to activate when the ignition is turned on but only if the (hidden from view) switch is in the "on" position. Not sure if all this is possible.
I have heard I ought to utilize a relay to avoid voltage loss at the pump. I have never hooked up a relay to anything before although I have heard of them being used. This system is being installed on a 1967 F250.
Ford Ranger / B-Series :: 1984 V6 - Electric Choke Replacement
I've got a '84 ranger that idles super fast for about 30 minutes after a cold start. The truck has been in the family since new and has done it since day one. I am wondering if replacing the electric choke or choke pull down would work. I've got a electric choke replacement but the cover place looks to be attached with rivets not screws. How to remove the choke?
View 3 RepliesFord Fuel System :: 1987 - Remove And Reinstall The Electric Connector?
My little '87 2.9 Ranger has little metal clips that hold the electrical connector onto the injector......how do I remove and reinstall the electric connector?
View 2 RepliesFord Fuel System :: 1987 F250 - Swapping Out Mechanical Pump For Electric?
I just purchased an 87 f250 w/ a carb'd 460. I purchased it with the mech fuel pump swapped out to an electric. The previous owner states that they gave him the wrong electric pump and I should exchange it for a different one. The reason for him putting it on was to get it running for me to hear it run.
My question: Is this even recommended? I wouldn't mind staying with an electric pump up front. If it is recommended, what would be a suitable pump to replace it with, as in flow/feeding characteristics?
Also, it only feeds from the rear tank, which also has a bad fuel pump. I'd like to get both tanks functioning again. I'd rather not deal with the tank switching valve due to what I've read about them. Has anyone ever hooked up a manual valve and just switched tanks that way? I've searched this site extensively and couldn't find anything. I know I'm not the first to have thought about it.