Ford - Electrical-wiring - Brakes - F150 - Sensors :: 1990 - Cruise Control Quit
I recently changed out the power boost canister for the brakes on a 1990 f-150 2wd. It was successful but now i have no cruise control. I double checked my plugs, all good. I checked my brake lights, all good. brake pedal seems fine and completely raised when not in use. i looked for a fuse and can't find it for that system, seems odd. it's not in fuse jct under dash, can't find a fuse jct under hood, seems odd also. No check engine light has lit.
View 3 RepliesFord Wiring/Electrical :: 1985 F150 - Hot Wire The Truck To Start?
My 85 f150 5L is parked to far in into my alley.. the last time i saw my keys i moved it up to water the plants that it was tucked almost on top of.
ive been looking for the keys for 2 months.. the truck isnt being driven at all but i think my neighbors are getting mad at it being out so far.
I can get in the engine bay, and i have jumped the starter on our big trucks at work before.. but what wires do i have to join to put the ignition into the run position?
Ford Wiring/Electrical :: Wiring For Cruise Control Switch
Looking for wiring diagram for the older Ford cruise control switches. I'm wanting to add an aftermarket system but use the factory switches. It's for a 99 ranger with the steering wheels like the mark 8s, older mustangs, explorers, and many others, had.
View 1 RepliesFord Wiring/Electrical :: 1996 Ranger - Adding Cruise Control?
i have a 96 ranger and want to put cruise control in it. is the wiring there and what other parts do i need to get without going aftermarket.
View 1 RepliesFord Wiring/Electrical :: 2006 F250 - Cruise Control Goes About 3 MPH Above Then Drops
I am trying to find out if Ford's cruise control has gotten crappy, or if mine has problems in my '06 F250. When I set the cruise, it goes about 3 MPH above what I set it at, then drops to about 3 MPH below, then it eventually stays where I set it. That is until I come to the top of an overpass or other small grade, then it is back to about 3 MPH over again as I reach the top and level out, then going back to where I set it.
The cruise control in my previous Ford trucks (83 & 91), as well as my 82 Mustang, 85 Lincoln, wife's 97 Toyota and the 2013 Chevy rental I just had, works fine. Where you set it is where it stays. Of course going up or down a steep grade, they all are going to lose or gain speed.
Anyway, I have taken the truck to the dealer twice for the cruise control. The first time is when I got the truck in '08. They replaced something else non-related, and said that would fix the cruise. It did work marginally, as the fluctuation was +-4 MPH before. I just took it in again before it goes off warranty, and they said the cruise is operating normally. So, there's my story. Is this normal, or is something wrong?
Ford Wiring/Electrical :: 1989 F250 - Horn And Cruise Control Not Working
I have an 89 f250 7.3. horn has not been working for the longest time the relay clicks but still nothing. It doesn't matter weather the key is in the on or off position. I know it might be a grounding problem because the cruise control does not work any more (even though recently it was working just fine). I didn't see any bad fuses.
View 6 RepliesFord Wiring/Electrical :: F250 - Intermittent Cruise Control / Running Self Test?
F250 6.8L .. So Ive read a lot of posts about intermittent cruise control issues. I understand that the most common failure is the brake switch on the master cylinder. My concern is that I am unable to run the cruise control self test I keep reading about. Does this test not work on my model year. I have tried even when the cruise control is working and still the cc light does no come on.
View 2 RepliesFord Wiring/Electrical :: Speedometer And Cruise Control Not Working / Fuse 18 Keeps Blowing
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 RepliesFord Wiring/Electrical :: Dark Blue Wire Connects To Cruise Control?
I have a wire that i think belongs to my Cruise control and I can't find out were it connects. It is dark blue/green stripe. It is in a wiring bundle with the oil sending wires ( two wires blk/w and y/o ).
I also get a code ....no sig from clutch neutral switch.
I just got done putting new heads on my little 2.9 and can't wait to use this as my daily drive. These two wiring issues are keeping my truck from running well enough to drive.
Ford Wiring/Electrical :: 1997 F250 HD Manual Trans - Cruise Control Inopertive
1997 F250 HD 7.3L It is a May build so is mainly 1996 parts. Came from the factory with auto transmission but PO did manual swap. Truck had factory cruise control but never worked after the swap. I found clutch safety switch missing so installed that and now it works as far as truck only starting with clutch in and other pins ohm good but it didn't fix the no cruise issue. All the diagrams I can find are wrong so I am stumped.
Horn works and steering wheel brushes appear to be functional.
Brake switch has 12V in and out so I think it is ok.
Brake switch on master cylinder has power in and out so I believe it is ok.
All brake lights work since I read that diagrams don't show it but they are somehow tied into the cruise.
I believe the issue is in the clutch safety switch (CPPS) wiring as I only have power on one wire however my colors don't match my Haynes or online diagrams. Also, no where can I find if this circuit runs on hot 12V or ground. Some wrong diagrams show hot 12V coming in on the light green wire from the brake switch but others show a hard ground on the red/Blu wire.
Most diagrams say I should have red/LtBlu, Red/LtGrn, LtGrn, Gray/Yellow. I actually have Red/Blue, White/Red, Tan/Blue, White/Brn. The White/Brn has power coming into the switch.
The connector for the automatic transmission column shifter is disconnected and the shifter was removed. I read that this needed to be jumpered to the tan/blue wire after a conversion on the CPPS but only on 2002 and up trucks so I don't think this affects me. That plug is for overdrive cancel.
Looking for a good diagram for a manual shift, diesel cruise control circuit that shows my color wires on the CPPS? I have had this truck 2 months and have fixed everything except this and will be making a long trip soon so cruise would be nice to have functional but I am stumped.
Ford Wiring/Electrical :: Brake Lights / Cruise Control / Rear Hazards Not Working
1991 F250 Supercab Diesel 4X4. I made a mistake while wiring up my trailer lights and ended up grounding out my brake controller, frying it. Along with that, I popped a couple fuses as well (1, 5 and 9 I believe). Replaced all fuses and got my signals (F/R) back at least.
Here's what's NOT working/messed up:
*Brake Lights
*Cruise Control
*Rear ABS light comes on a few minutes after driving.
*Front hazards work, not rear. When I apply the brake, the hazards pause in the on position.
I've tested the brake switch on the brake pedal (Green/Red and Green) and it works properly. So, current is obviously not reaching the rear brake lights.
Another note. The truck is wired with a 7 pin plug in the bed for a goose neck trailer. It also was wired to a 6 pin on the bumper. I replaced the 6 pin with a 7. The signal/brake pins on the plugs (both) and also not receiving power. What's the next thing to check?
Ford Wiring/Electrical :: 2014 F150 - Starting System Fault / Body Control Module Malfunctioned
I own a 2014 F-150 XLT 3.5 L 6 cyl Twin. Saturday afternoon I tried to start the truck once and it didn't start like it normally does. It started on the second try, but the A/C didn't work and I got a "Starting System Fault" warning on my screen. When I shut the truck off, it would not start at all. All the lights and gauges worked, just no start.
Had to tow it to Ford Dealer, where the service department had already closed for the day (of course). Today it was determined by the service department that the Body Control Module had malfunctioned. I was told that the tech tapped on the control module and the truck started. Now waiting two days for a replacement part to come in. Luckily, I'm just under 36K miles and three years. Is this a common occurrence?
Ford Wiring/Electrical :: 1985 - After TPS Sensor 0 Volts?
I have an 85 bronco ii 2.8l, carb, with around 109K on it , ran pretty good, some stubles here and there but found out how to read codes and went from there.... Retreived codes 23, 31 and 84. Checked TPS, had voltage to sig return pin but was low, pulled the carb, bought a rebuild kit while i was at it and redid most of the gaskets but did not take the inner parts of the carb out, put on a new TPS, installed the carb, unhooked battery for about half an hour and noticed it idled very high. Once you were moving the rpm's would drop but at idle would climb again. I ran the codes again and got 31, 63 and 84. checked volts from black to vref i have 4.9 and from black to sigrtn i have 0. i have traced all 3 wires through the bundle and did not see any breaks i know that the green wire goes to the ECM? but i do not know what to check from this point.
View 2 RepliesFord Wiring/Electrical :: 1987 F150 - Wiring Diagram With Carburetor?
Looking for a wiring diagram for a F-150 XLT LARIAT 5.8L 4BBL, all the books I have looked at show the wiring for this year with fuel injection and this truck came with a 351W with a Holley 600 4BBL, I have a few wire's in the engine compartment that melted away all the insulation, they are located close to where the harness passes the firewall before the ignition module. Is this a common problem on old models ?. Need a clear copy of the correct diagram for a f-150 1987 with carburetor, how I can get a copy so I can fix this problem before it gets worse.
View 3 RepliesFord Ranger / B-Series :: 1985 - Electrical Wiring / Brake Lights Not Coming On
85 ford ranger 2.3 efi .. My brake lights still aren't coming on. According to the Haynes manual, the wire that runs from the stop light fuse goes from there to the hazard flasher and then to the brake light switch. Since I have checked everything else, is it possible that the hazards are causing a break in the connection?
View 4 RepliesFord Wiring/Electrical :: 1985 - Driver Side Brake Light And Turn Signal In The Back Quit Working
85 f150. My driver side brake light and turn signal in the back quit working. The tail light works tho which is a different filament. The bulb is good and I changed the flasher relay...the circle thing in the fuse panel. Everything else works just fine. looking for a starting point.
View 7 RepliesFord Wiring/Electrical :: 1995 F150 - Headlights Not Turning On
Here's the breakdown. I have a '95 Ford F150 that I bought the previous year and it has been nothing but a problem. The most recent problem is the attempt to turn on the headlights. I will pull the plunger to turn on the headlights but I will only get the parking lights and when attempting to turn on the high beams I still get nothing. The only way that I get any sort of lighting is if I pull on the turning stick (almost like doing a manual override on a tripped wall plugin). Now here's the kicker. I still have parking lights, brake, tail, cab, and dash lights. Winter in quickly approaching and the nights are already getting dark, pretty soon the days will be just as dark.
View 3 RepliesFord Wiring/Electrical :: 1988 F150 - Speedometer Not Working
I got my first truck today and it's a 1988 Ford F-150 and it runs great! The only issue is that the speedometer doesn't work and I won't be able to register it until it does. I was wondering what I can try out to maybe fix the issue and if not, how I would replace it. Every other gauge works, it's just the speedometer that isn't. The needle doesn't move at all it just sits at a 0 all the time.
View 8 RepliesFord Wiring/Electrical :: 1991 F150 4x4 - Speedometer Not Working?
I have been trying everything to get my speedo working on my Ford. It didn't work for 3 months after I got it then I decided to put some gear oil on the cable. This made it work for about 200 miles then it would only work with the clutch in and then not at all. I've replaced the speed sensor(not one on rear end the thing the cable goes into), and the gear that goes on the end of it. If I hook a drill up to the cable the tach moves. Could the cable be stretched or just needs some speedo cable lube?
View 5 Replies