Ford Wiring/Electrical :: 2006 F250 - Cruise Control Goes About 3 MPH Above Then Drops
I am trying to find out if Ford's cruise control has gotten crappy, or if mine has problems in my '06 F250. When I set the cruise, it goes about 3 MPH above what I set it at, then drops to about 3 MPH below, then it eventually stays where I set it. That is until I come to the top of an overpass or other small grade, then it is back to about 3 MPH over again as I reach the top and level out, then going back to where I set it.
The cruise control in my previous Ford trucks (83 & 91), as well as my 82 Mustang, 85 Lincoln, wife's 97 Toyota and the 2013 Chevy rental I just had, works fine. Where you set it is where it stays. Of course going up or down a steep grade, they all are going to lose or gain speed.
Anyway, I have taken the truck to the dealer twice for the cruise control. The first time is when I got the truck in '08. They replaced something else non-related, and said that would fix the cruise. It did work marginally, as the fluctuation was +-4 MPH before. I just took it in again before it goes off warranty, and they said the cruise is operating normally. So, there's my story. Is this normal, or is something wrong?
Ford Wiring/Electrical :: 1989 F250 - Horn And Cruise Control Not Working
I have an 89 f250 7.3. horn has not been working for the longest time the relay clicks but still nothing. It doesn't matter weather the key is in the on or off position. I know it might be a grounding problem because the cruise control does not work any more (even though recently it was working just fine). I didn't see any bad fuses.
View 6 RepliesFord Wiring/Electrical :: 1997 F250 HD Manual Trans - Cruise Control Inopertive
1997 F250 HD 7.3L It is a May build so is mainly 1996 parts. Came from the factory with auto transmission but PO did manual swap. Truck had factory cruise control but never worked after the swap. I found clutch safety switch missing so installed that and now it works as far as truck only starting with clutch in and other pins ohm good but it didn't fix the no cruise issue. All the diagrams I can find are wrong so I am stumped.
Horn works and steering wheel brushes appear to be functional.
Brake switch has 12V in and out so I think it is ok.
Brake switch on master cylinder has power in and out so I believe it is ok.
All brake lights work since I read that diagrams don't show it but they are somehow tied into the cruise.
I believe the issue is in the clutch safety switch (CPPS) wiring as I only have power on one wire however my colors don't match my Haynes or online diagrams. Also, no where can I find if this circuit runs on hot 12V or ground. Some wrong diagrams show hot 12V coming in on the light green wire from the brake switch but others show a hard ground on the red/Blu wire.
Most diagrams say I should have red/LtBlu, Red/LtGrn, LtGrn, Gray/Yellow. I actually have Red/Blue, White/Red, Tan/Blue, White/Brn. The White/Brn has power coming into the switch.
The connector for the automatic transmission column shifter is disconnected and the shifter was removed. I read that this needed to be jumpered to the tan/blue wire after a conversion on the CPPS but only on 2002 and up trucks so I don't think this affects me. That plug is for overdrive cancel.
Looking for a good diagram for a manual shift, diesel cruise control circuit that shows my color wires on the CPPS? I have had this truck 2 months and have fixed everything except this and will be making a long trip soon so cruise would be nice to have functional but I am stumped.
Ford Wiring/Electrical :: Wiring For Cruise Control Switch
Looking for wiring diagram for the older Ford cruise control switches. I'm wanting to add an aftermarket system but use the factory switches. It's for a 99 ranger with the steering wheels like the mark 8s, older mustangs, explorers, and many others, had.
View 1 RepliesFord Wiring/Electrical :: 1996 Ranger - Adding Cruise Control?
i have a 96 ranger and want to put cruise control in it. is the wiring there and what other parts do i need to get without going aftermarket.
View 1 RepliesFord Wiring/Electrical :: Speedometer And Cruise Control Not Working / Fuse 18 Keeps Blowing
I have a 1994 f150 5.0 engine and automatic transmission. Problem I am having is speedometer, cruise control is not working. Overdrive light is flashing and number 18 fuse keep blowing. horn is still working...
View 1 RepliesFord Wiring/Electrical :: Dark Blue Wire Connects To Cruise Control?
I have a wire that i think belongs to my Cruise control and I can't find out were it connects. It is dark blue/green stripe. It is in a wiring bundle with the oil sending wires ( two wires blk/w and y/o ).
I also get a code ....no sig from clutch neutral switch.
I just got done putting new heads on my little 2.9 and can't wait to use this as my daily drive. These two wiring issues are keeping my truck from running well enough to drive.
Ford Wiring/Electrical :: 1985 F150 - Location Of Cruise Control Amplifier
Where is the cruise control amplifier located on an 85 F-150? The Chilton manual just says "behind the instrument panel". No pic or further description. Just looking up from the bottom of the dash I see a "black box" with 2 wires going into the top of it located just between the steering column and the wiper switch.
Is this it?
Ford - Electrical-wiring - Brakes - F150 - Sensors :: 1990 - Cruise Control Quit
I recently changed out the power boost canister for the brakes on a 1990 f-150 2wd. It was successful but now i have no cruise control. I double checked my plugs, all good. I checked my brake lights, all good. brake pedal seems fine and completely raised when not in use. i looked for a fuse and can't find it for that system, seems odd. it's not in fuse jct under dash, can't find a fuse jct under hood, seems odd also. No check engine light has lit.
View 3 RepliesFord Wiring/Electrical :: Brake Lights / Cruise Control / Rear Hazards Not Working
1991 F250 Supercab Diesel 4X4. I made a mistake while wiring up my trailer lights and ended up grounding out my brake controller, frying it. Along with that, I popped a couple fuses as well (1, 5 and 9 I believe). Replaced all fuses and got my signals (F/R) back at least.
Here's what's NOT working/messed up:
*Brake Lights
*Cruise Control
*Rear ABS light comes on a few minutes after driving.
*Front hazards work, not rear. When I apply the brake, the hazards pause in the on position.
I've tested the brake switch on the brake pedal (Green/Red and Green) and it works properly. So, current is obviously not reaching the rear brake lights.
Another note. The truck is wired with a 7 pin plug in the bed for a goose neck trailer. It also was wired to a 6 pin on the bumper. I replaced the 6 pin with a 7. The signal/brake pins on the plugs (both) and also not receiving power. What's the next thing to check?
Ford Wiring/Electrical :: 2001 F250 - Auto To ZF6 Swap Cruise Not Working
I have a 2001 F250 with 7.3. We swapped the auto for a zf6 manual. We left the auto's shift position sensor tied to the frame and left in neutral. I did install a pcm from a manual transmission pickup. Also have the clutch position switch hooked up. I have an Edge Evolution CTS2 reprogrammer, and on the display the gear indication always shows P. I suspect that is why my cruise doesn't work. For interests sake, I tried manually adjusting the shift position sensor through all gears, and the reverse lights come on when in reverse but the Edge's display always shows P. My question is with a manual transmission, how does the pcm know that it is in gear? The only sensor that I am aware of is the reverse sensor on the zf6.
View 4 RepliesFord Wiring/Electrical :: 1979 F250 Starter Keeps Running
I have a 1979 f-250 4x4 with a 351m. The problem I am having is my starter keeps running after the truck starts and also after I shut off the key. I didn't get the battery unhooked in time today and it completely melted the lug off on the solenoid, but the other wires were barley warm. What could be causing this problem? The battery is new, the cables are new and the Sol. was new. Maybe the switch or the starter?
View 8 RepliesFord Wiring/Electrical :: 2007 F250 - Power Out On Cabin Temp Control Panel
Well I've had her just 1 week, used, and today I turned it on and the power is out on the A/C n Heater /Fan Control ASSY. It worked the last 900 miles from FL to OH. And today worked this morning, but 2nd time I got in the truck today there was No Lights in the Air Control Assy. I didn't get an Owners Manual, so what fuse to check.
View 3 RepliesFord Super Duty (1999-2016) :: 2009 F250 - Intermittent Cruise Control Failure
For about 6 months the cruise control on our '09 F-250 has been intermittently failing. One time I'll set it and it will work fine, the next time I try to set it and it fails. No particular rhyme or reason to when it fails to set.
Some of the tests that I did indicated it was the brake light switch on the brake pedal arm. It seemed to work perfectly a few times that I drove it after the installation but now it's back to working when it wants to.
I had a problem with the cruise on our '06 Ranger and it turned out to be the module. It acted a bit the same way in that it would set sometimes, other time not. I don't know if the two systems are similar or not.
Ford Wiring/Electrical :: 2000 F250 - Dash / Parking And Tail Running Lights Not Working
I have a 2000 Ford F250 lariat 7.3 .... This vehicle has an aftermarket double din stereo pillar gauges for Pyro meter and transmission temp and has also had a snowplow attached but since re moved since I purchased it. It also has H ID headlights, which are run by the passenger side headlight connection.
The problem I'm having is that whenever I turn on the parking lights it is blowing the number eight fuse under the hood. Which is giving me no dash lights running lights parking lights or taillights. Initially the fuse would last for a few minutes and then burn out. I should also add that the trailer wiring harness doesn't work either and the driver side headlight will work sporadically.
Ford Wiring/Electrical :: 7 Pin Trailer Wiring - Running Lights Not Working
Just bought an 04 Super duty with the factory plug 7pin and 4 pin plug. Checked the fuses and finally tracked down the 2 relays under the hood but can't seem to find anything wrong. Everything on the trailer works except for the running lights. Is there another fuse or something I have missed? Trailer works fine on my buddies Duramax and worked fine on my old 97.
View 14 RepliesDodge - Electrical-wiring - Ram50 :: 1995 - Intermittent Dash Panel Electrical Malfunction?
My beloved 1995 Dodge Ram Van has intermittent dash panel electrical issues. The gas gauge an speedometer are intermittent, coupled with lights and radio on off too. It It all started when I had the transition services years ago. It has less than 100k mileage.
View 1 RepliesFord Wiring/Electrical :: 1997 F250 - Rear Tail Lights Wiring
I have a 97 F250 HD. Wiring the rear tail lights. When we bought it the had cut off the wires going to both sides of the rear lighting assemblys and I was wondering what wire went to what i have the left turn signal working just can't seem to get the brake/back up light to work on that side and i can't figure out how to get the right side going either.
View 8 RepliesFord Wiring/Electrical :: 1999 F250 - Door Courtesy Light Wiring Diagram
I am trying to add courtesy lights to the existing reflectors in the front doors of my supercab. I can't find a wiring diagram that shows where to connect the light sockets. 1999 F250 SD...
View 2 Replies