Sonata I45 (LF 2015+) :: Code P2006 Intake Manifold Runner Control Stuck On Closed

Check Engine Code P2006 intake manifold runner control stuck on closed? Taking it in to have it checked out.

View 10 Replies

Passat (B6) :: CEL Lasted Only Three Days - Intake Manifold Runner Control Failure

Well, I had a check engine light that lasted only three days then it cleared itself without any intervention. I checked it with a vag-com and I discovered there was an issue with the intake manifold control. I ended up bringing it to the dealer since it is a fairly new passat, and the service department informed me that the Intake Manifold Runner Control needed to be replaced.

Below were the fault codes.

3 Faults Found:
012599 - Intake Manifold Runner Control: Basic Setting not Completed
P3137 - 001 - Upper Limit Exceeded - Intermittent
Freeze Frame:
Fault Status: 00100001
Fault Priority: 0
Fault Frequency: 1
Mileage: 33815 km
Time Indication: 0

[Code] .....

View 3 Replies

Dodge - Avenger :: 2008 - Intake Manifold Runner Control Valve Stuck Open

Check engine light computer scan indicates intake manifold runner control valve stuck open. Will it damage the car to drive it in this condition and what does fixing it entail?

View 4 Replies

Tiguan :: CEL On - P2015 Intake Manifold Runner Position Switch Code

I have a 2011 Tiguan S 4Motion with just over 63k Miles which for the most part has been problem free and great to drive since I leased it at 40k miles. About 2 weeks ago my CEL came on and I used the Torque app on my phone to check the code and it was the apparently well known P2015 intake manifold runner position switch code. The car was running perfectly fine so I cleared the code and it stayed off for about a week before coming back on with the same fault again yesterday. I have a couple of questions for the much more knowledgeable than I people in this forum around this code.

First - I've read in several places that VW has placed an extended warranty on the manifold and fuel injectors for the 2.0 TSI and that this code is usually an indicator that the manifold needs to be replaced under this warranty. What I haven't found though is conclusive info on is whether the 2.0T in my 2011 Tiguan is covered under this extended warranty. Since this code so conveniently is popping up just 3k miles past the end of my 60K mark, I'd like to know this. I leased the car from Enterprise, not a dealer so I'm worried that whatever dealer I take it too will try to bend me over on the service so the knowledge that the manifold is still covered would be at least some comfort.

Second - I won't be able to get it in to a service department until mid next week and I have a 300 mile trip to make this weekend. The car is driving fine as far as I can tell so I'm not overly concerned. I do my own basic maintenance i.e. oil changes, plugs/coil packs etc. but I'm thinking changing the manifold would be a little bit out of my comfort zone..

View 4 Replies

Ford - Windstar :: 2002 - Intake Manifold Left Bank Stuck Open

I bought a 2002 Ford Windstar, it has over 154,000 miles on it. My problem is I got a ODB II code reader and it said that the Intake manifold on the left bank is stuck in the open position. How do I keep it from sticking.

View 15 Replies

Ford - Windstar :: Code P0113 - Intake Air Temperature Sensor 1 Circuit High Input

Check engine light is on, this is the code that came up when checked at OReillys, "P0113 Intake Air temperature sensor 1 Circuit high input". Earlier took it to repair shop, he did not give the code, some sensor needs to be changed (don't know if he came up with same code). He had erased the code but it came back on within minutes. Wanted to check if there is any cheaper way to fix this. This is a windstar van.

View 15 Replies

Grand AM :: 1998 3.1L V6 - Engine Intake Manifold Gasket Leaks

Leaking intake manifold gaskets on General Motors 3.1L V6 engines? Mine is a 1998 Grand Am with low milage (40K) and I have been told I need to spend $900 to replace the intake manifold gasket because it is leaking antifreeze into the engine oil.

View 8 Replies

Pontiac - Bonneville :: 1998 - Intake Manifold Leaking A Fluid On Right Side

I've currently have 114,000 miles on this Pontiac Bonneville and I replaced the intake manifold last summer. Recently, I have been having issues with the intake manifold leaking a fluid on the right side of it (facing the engine) and been having dirt or some other type of fluid mixing in my fluid tank. The leak has been causing some smoking issues. Also, when I start the car in the morning white smoke comes out of the back of it. Where I need to start so that I can get this fixed. I'm assuming something went wrong in the replacement.

View 6 Replies

Ford 6.7L Power Stroke Diesel :: CEL With Code P2074 - Cracked Intake Manifold?

I was chasing down a P2074 CEL and thought it was a stressed wiring harness connection on the MAF.

Took it to the Ford house and they chased it for 2 days, believing it was the MAF and air filter. They told me that air filter was allowing to much air in. My thoughts was, that is was what MAF is for, to regulate the fuel based on how much air was going in.

I just found out that they are stating that an AFE dry air filter contributed to a cracked intake manifold because the aftermarket air filter made the intake get too hot.

View 3 Replies

Golf/GTI VI :: CEL Code P2015 - Intake Manifold Bad

My husband has a 2011 GTI, which has just hit the 40k mileage mark. His CEL started coming on in March, but we figured it was due to him not tightening the gas cap enough, as he'd open and relock the gas cap, and the CEL would go away within a few restarts of the car. Took it into the stealership last week, got the 40k service (which was a bit of a rip-off in itself), and then got told the manifold was bad.

This is the exact text for the invoice: "Checked the vehicle for codes and found code P2015. Traced the intermittent failure to the intake manifold valve flap sensor failing."

I've seen a lot of posts around this problem, for many models and years, but it seems like most people managed to get it repaired under warranty / TSB. So I have three questions:

1. In the OBD codes, does it store date as well as code? In other words, is there a way to prove that this failed under 36k miles?
2. What's the process for getting this escalated to VWOA customer care, since I feel this should be taken care of under warranty?
3. The dealership we took the car to (which is not where we purchased the car, but is just closer to home) was shady, and the guy we worked with was, to say it nicely, a jerk.

View 3 Replies

Passat (B6) :: Replaced Intake Manifold But P0016 Code Still Remaining

Some technical issues here. Had the intake manifold replaced under extended warranty ('09 2.0 TSI, 115,000km); they cleaned out the carbon as well. There were all sorts of codes it was throwing, despite having new coils and plugs installed.

One more thing to do. I still have Crank Position Sensor code showing. Car runs fine (much better now actually),but I was told if I don't get this last code looked after, one day the car just won't start.

View 1 Replies

Ford Super Duty (1999-2016) :: 2005 F350 - Melted Air Intake Manifold Port - Code P0171 And P0174

Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.

Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?

View 5 Replies

Prius (2001-03) :: Engine Runs Then Stalls / P3191 Code - Oil In Intake Manifold?

Looking at a 2003 Prius with 77K miles. Turn the key, the engine starts, runs smooth for about 5-7 seconds. After that it starts to run rough and rattle, then shuts off. The only code I pulled was P3191. I pulled off the air cleaner to clean the throttle body, and noticed a small pool of oil in the bottom of the intake manifold. Is that normal, or could that be causing the code issue? BTW, I cleaned the MAF and throttle body, and the engine still does the same thing.

View 14 Replies

Ford - Windstar :: 2002 - Pipe Where Heater Hose Hooks On The Manifold Is Leaking Antifreeze

On the manifold there is a metal/steel pipe that the heater hose hooks to. That pipe is leaking anitifreeze. It has a small hole in it. Is this pipe replaceable or is it part of the manifold.

View 19 Replies

Ford 6.7L Power Stroke Diesel :: CEL Code P02E1 - Diesel Intake Air Flow Control Performance

My truck threw a CEL after the first start today. The CTS reports it twice. I noticed it about two minutes after start.

P02E1 - Diesel Intake Air Flow Control Performance

The air box gauge is green and it doesn't reset when I push it so that appears to be fine.

The one thing I can easily notice is the sound of the turbo. Typically when I stop and park, the turbo spools up, then down, then spools again and gives a sigh of relief and it's then silent. It's not doing that currently.

Now, I can hear it constantly when parked and it spools down after I turn off the engine, even two minutes later. That is not normal for my truck when I wait for the above to finish its routine. When I start the truck, the turbo immediately spools to where I can hear it which is also not normal, as if it's building 0.5 psi. I realize that's funny to say on a turbo diesel but I know the sounds of my truck. The EGT's are fine, EOT, ECT, TFT are fine and I can build boost when driving without issue. I took the drive to work easy this morning so the highest I noticed was 10 psi.

I restarted the truck after a 20 minute drive to the office and it didn't clear the CEL. The CTS squawked four times when it woke up the second time but it didn't show me which PID it was upset about.

I'm thinking this has nothing to do with the CAI and this is something downstream of there. EGR related? I haven't opened the air box yet, at work and in dress clothes so that'll need to wait. My past four or five regenerations all started between 1.94 and 1.97 soot gpl. That is also not normal and is something I have been keeping my eyes on. Currently the DPF is at 2.10 so it has made it further. Normal behavior (post emissions flash) is above 2.54 soot gpl for an AR.

View 4 Replies

Ford F-150 (2004-2008) :: Intake Manifold Replacement?

Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.

View 6 Replies

Ford Excursion :: 2001 V10 - Intake Manifold May Be Cracked

What are signs the intake manifold may be cracked? 2001 V10 Excursion....

View 4 Replies

Ford F-150 (2009-2014) :: Intake Manifold Swap?

Will an intake manifold from a new mustang 5.0 fit on a 2014 F150 5.0?

View 3 Replies

Ford Ranger / B-Series :: 2003 - Intake Manifold Leaking?

'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.

Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.

I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.

Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.

Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?

View 6 Replies