Ford 6.7L Power Stroke Diesel :: CEL With Code P2074 - Cracked Intake Manifold?

I was chasing down a P2074 CEL and thought it was a stressed wiring harness connection on the MAF.

Took it to the Ford house and they chased it for 2 days, believing it was the MAF and air filter. They told me that air filter was allowing to much air in. My thoughts was, that is was what MAF is for, to regulate the fuel based on how much air was going in.

I just found out that they are stating that an AFE dry air filter contributed to a cracked intake manifold because the aftermarket air filter made the intake get too hot.

View 3 Replies

Ford F-150 - 1997-2003 :: 2001 5.4L - Intake Manifold And Gaskets Replacement

I am about to replace the intake manifold and gaskets. I know all of that process, but first question is if there is anything i should do whilst in there. Second question; what can I do with my intake to get more power? Mainly just kind of wondering before I get my parts ordered.

View 4 Replies

Ford Ranger / B-Series :: 2001 4.0 SOHV Upper Intake Manifold Removal

It doesn't look anything like the illistration in my Haynes book.Where are the bolts located and how many?

View 14 Replies

Ford F-150 - 1997-2003 :: 2001 - Leak Where The Water Transfer Connects To Intake Manifold

I have a 2001 F150 Super Crew 5.4. I had a leak where the water transfer connects to the intake manifold. I decided to get a new manifold rather than trying to repair it. The new manifold from Dorman came and the gaskets were built into the manifold. I torqued the manifold to specs. I replaced everything and it starts fine.

I can hear what sounds like a leak, but can't find anything. I checked every hose that is connected and they are all snug and connected. I had the check engine light checked and it said it was running lean on both sides (p0174, p0171). Also a p0122. I thought something might have damaged the Throttle Body Position Sensor, so I replaced it...but no change.

I'm still driving it everyday because I need to. It won't change gears so smoothly sometimes. The most noticeable problem is that the A/C doesn't work. It just blows hot air. And the worst part about it is...it does it even when the air isn't turned on! I just go around with the windows down...in 95+ degree heat...with hot air blowing!

This is my first time to attempt a manifold change out. What I should check?

View 4 Replies

Santa FE SM (2001-06) :: Fluid Leaking At Intake Manifold

2.4 Santa Fe ... I just took my Car to MOT inspection and found out there's a leak at my intake manifold and it's coming out of this place. it feels like brake fluid but my brake fluid is full?? I have seen many cars but never seen a part like this before. what is it doing there and why is it leaking ?

View 6 Replies

Rodeo :: 2001 V6 / How Many Bolts Actually Holding Intake Manifold Onto Heads

How many bolts actually holding the intake manifold onto the heads. Are there more inside the plenium when you take the top off or can you remove the unit as one piece to replace the intake manifold gaskets?

View 1 Replies

Prius (2001-03) :: Engine Runs Then Stalls / P3191 Code - Oil In Intake Manifold?

Looking at a 2003 Prius with 77K miles. Turn the key, the engine starts, runs smooth for about 5-7 seconds. After that it starts to run rough and rattle, then shuts off. The only code I pulled was P3191. I pulled off the air cleaner to clean the throttle body, and noticed a small pool of oil in the bottom of the intake manifold. Is that normal, or could that be causing the code issue? BTW, I cleaned the MAF and throttle body, and the engine still does the same thing.

View 14 Replies

Ford Excursion :: 2001 V10 - Cracked Heater Line - Passenger Side Header Melted

It seems that the install of my Doug Thorley headers didn't go as well as I thought. Turns out the passenger side header melted the bracket holding the heater lines and then punctured one of the lines when it rubbed against the header. Right now I'm not sure what to do. I noticed the melted bracket and pulled the fender well, but that's when I noticed the leak. I guess some of the melted plastic was keeping it from leaking everywhere until I removed it. I live in AZ so the rear heater isn't really necessary so if a stop gap measure is to bypass it then I'm game but I can't find any info on how to do it. If the only real solution is to get the entire line replaced then I'm a bit hosed I guess. 2001 V-10 4x4 BTW.

View 6 Replies

Ford F-150 - 1997-2003 :: Passenger Side Exhaust Manifold Cracked

2003 F150 5.4 4x4 supercrew ,76k miles

Recently the passenger side exhaust manifold cracked on my truck. I bought this truck about two years ago with 58k on it and currently have 76k miles. I remember getting the carfax report and being relieved to see that it had exhaust manifold replaced in July of 2014 at 49K miles along with a new EGR tube. I called the shop that worked on the truck to see if he could confirm that both manifolds were replaced since carfax only said manifold & egr tube. The shop manager confirmed that both manifolds were replaced and he told me that they were most likely manifolds from napa according to the part number.

Now, my question is, what's the best brand to replace the manifolds with? Should I just go with OEM and spend the extra $130 per side? I know the manifolds are a common problem with these trucks but only lasting three years and 27K miles just seems ridiculous to me.

I'm hoping that when I get around to actually doing this that they wont be to bad because of how recently they were replaced. For now I just cleaned the area with a wire wheel and used the inferno metal repair. Seems to have done the job but I don't expect it to last long, just another month or two until I move to a place where I can actually work on my vehicles.

View 1 Replies

Ford Super Duty (1999-2016) :: 2008 - Cracked Exhaust Manifold

My '08 S.D. (5.4) has a cracked exhaust manifold, which I've heard is fairly common. Crappy Ford design. The local dealer has them in stock (imagine that, just like the 'non-bad' coil caps from some years ago, that they were instructed by Ford to keep at least 10 on stock at all times) for the passenger and driver's side. What are the part numbers?

View 10 Replies

Ford F-150 - 1997-2003 :: Exhaust Manifold Gasket Cracked - Ticking Sound?

If the exhaust manifold gasket is broke / cracked will it making a ticking sound?

View 5 Replies

Ford F-150 (2004-2008) :: Intake Manifold Replacement?

Looking for any pictures or directions on replacing the intake manifold on the 2004 F150, 5.4. Got all the parts with the pulgs, and ignition coils.

View 6 Replies

Ford F-150 (2009-2014) :: Intake Manifold Swap?

Will an intake manifold from a new mustang 5.0 fit on a 2014 F150 5.0?

View 3 Replies

Toyota - Matrix :: Cracked Exhaust Manifold?

The guy at the muffler place says I have a cracked exhaust manifold. He also says he can't get the parts after holiday. I'm supposed to drive, with my family for holidays. The muffler guy says that should be fine - highway driving will generate enough airflow to keep us from all dying of CO asphyxiation.

View 17 Replies

Golf IV / Jetta IV :: Exhaust Manifold Is Cracked?

I have a 2001 Jetta 2.0L standard transmission I believe my exhaust manifold is cracked looking for a replacement. There is a local guy selling one off a 2001 golf wondering if that would work on my car..

View 1 Replies

Ford Ranger / B-Series :: 2003 - Intake Manifold Leaking?

'03 Ranger, 2.3L. Runs great except at idle. Code p0171. Replaced IAC, no luck.

Brake cleaner leak test definitely results in engine rpm change right around "butterfly rod" plug in front of intake manifold near no. 1 cyl. I'm pretty sure that's the problem - the plastic plug blew out. I watched a video showing repair, but it seems lacking.

I do not want to loosen up intake for access - I'd rather remove steering pump and gain some access to plug it up. There still isn't much access but, but eyeballing it, enough to plug, I think.

Three steering pump bolts came out easy. The fourth one is behind fluid line - extremely difficult to access, imo.

Somehow try to remove pump for access to intake hole, or bite the bullet and remove intake manifold for access?

View 6 Replies

Ford F-150 - 1997-2003 :: 4.2L V6 - Intake Manifold Gasket Leak?

I've got a 1997 F150 with the 4.2L V6. Before I got it last summer I did some research, but apparently missed the issue with the intake manifold gasket leaks on these early engines. It seems to be a very slow leak, but obviously I want to get it fixed. I called Ford to see if it had had the recall work done on it, but all they could tell me is that there wasn't an open recall on my truck (with the exception of the recent fuel tank strap recall). Their system apparently only goes back 10 years, so they couldn't even see the freakin' recall. So, I've got a few questions:

1) I know I didn't post much info, but does this seem like an intake manifold leak?

2) Are there any special tools needed to change out the gasket myself?

3) Can you all recommend any replacement gaskets? I found a few different manufacturers of gaskets, but I'm sure some are better than others.

4) Can this issue cause the computer to throw the loose gas cap code (P0455 if I recall correctly).

5) Would it be worth it to just get a new truck? I really wanted a diesel in the first place, but I also hate to give up on a nice truck with only 115,000 miles.

View 6 Replies

Ford F-150 - 1997-2003 :: Ticking Noise In Intake Manifold

Replaced head gaskets on 2003 f-150 5.4. Now I can hear a ticking noise in middle of intake by #5 port. Maybe timing is off 1 link?

View 4 Replies

Ford Ranger / B-Series :: 1987 V6 - Intake Manifold Removal?

I was working on my friend's '87 Ranger with 2.9 L V6, and a little bit of dirt fell into the intake manifold through the injector ports and intake ports. I should've cleaned the top of the engine with a shop vac first. Anyway, should I remove the intake manifold, or try to vacuum the bits out? It's pretty oily inside, and they might be stuck to the inside of it, so the vac might not do much. If I have to remove it, do I have to de-mesh the distributor gear to remove it, or does the distributor attach to a splined shaft? After looking at the diagrams, the answer was unclear.

View 1 Replies