Tiguan :: CEL On - P2015 Intake Manifold Runner Position Switch Code
I have a 2011 Tiguan S 4Motion with just over 63k Miles which for the most part has been problem free and great to drive since I leased it at 40k miles. About 2 weeks ago my CEL came on and I used the Torque app on my phone to check the code and it was the apparently well known P2015 intake manifold runner position switch code. The car was running perfectly fine so I cleared the code and it stayed off for about a week before coming back on with the same fault again yesterday. I have a couple of questions for the much more knowledgeable than I people in this forum around this code.
First - I've read in several places that VW has placed an extended warranty on the manifold and fuel injectors for the 2.0 TSI and that this code is usually an indicator that the manifold needs to be replaced under this warranty. What I haven't found though is conclusive info on is whether the 2.0T in my 2011 Tiguan is covered under this extended warranty. Since this code so conveniently is popping up just 3k miles past the end of my 60K mark, I'd like to know this. I leased the car from Enterprise, not a dealer so I'm worried that whatever dealer I take it too will try to bend me over on the service so the knowledge that the manifold is still covered would be at least some comfort.
Second - I won't be able to get it in to a service department until mid next week and I have a 300 mile trip to make this weekend. The car is driving fine as far as I can tell so I'm not overly concerned. I do my own basic maintenance i.e. oil changes, plugs/coil packs etc. but I'm thinking changing the manifold would be a little bit out of my comfort zone..
Tiguan :: Code P2015 - How To Replace Entire Manifold
Had a P2015 code today on my 2009 Tiguan. Does this mean I have to replace the entire manifold ?
View 6 RepliesGolf/GTI VI :: 2011 - Got CEL And Error Code P2015?
Soild CEL, autozone pulled a P2015 code, but couldnt find it for VW in their system, just hyundai, toyota, dodge, and kia codes came up.
Looked around and everywhere says it's the notorious MKVI IM replacement issue.. Im under PT warranty until Nov. '15 so im good there.
Heres the catch.. sometimes it goes off without any changes to the vehicle. First thing (before the obd2 reader from autozone) i checked was my gas cap, that will cause a CEL sometimes, next time I started the car the CEL was off. the next day, without touching the gas cap since, the CEL was on again, today its off
car idles fine, drives fine, MPG are fine, pulls fine, stops fine, steers fine, everything works in the car. year: 2011
Passat (B6) :: Replaced Intake Manifold But P0016 Code Still Remaining
Some technical issues here. Had the intake manifold replaced under extended warranty ('09 2.0 TSI, 115,000km); they cleaned out the carbon as well. There were all sorts of codes it was throwing, despite having new coils and plugs installed.
One more thing to do. I still have Crank Position Sensor code showing. Car runs fine (much better now actually),but I was told if I don't get this last code looked after, one day the car just won't start.
Golf/GTI VI :: CEL Code P2015 / Flap Motor Not Working Correctly
I got the known p2015 code about a month ago and the CEL is on. Here is my situation though...I went and had my car tuned for an APR stage 1+ tune with stock hardware, everything was fine. I then upgraded to a catless 3 inch downpipe (ebay on that links up to the stock downpipe) and a short ram intake and decided to go to the 2+ to delete the engine code for not having a cat.
While I was there, the guy tuning my car said on top of the code for not having a cat, there was a code for my intake manifold saying that one of the motors for a flap wasn't working correctly. I left there expecting to see a code but it never came back on. After4-5 months, I had to pass emissions. Obviously you cant pass with the 2+(found that out the hard way) so I had to have it returned to a regular stage 1 with the stock downpipe. Still no sign of a code for the intake manifold.
I passed emissions and then put my downpipe back on, however, I decided to buy the 200 cell cat from 42DD to weld into my downpipe to save me from having to constantly get my car tuned just to pass emissions. After welding in the cat, I still had a CEL. I went to advance auto and it said I had a code p2015 Intake Manifold Runner Sen Sw Ckit Rng/Perf B1.
I went and got my car tuned to the stage 2 for the hi flow cat and the light is still on. My question is, do I need to replace the whole intake manifold or is there a possibility that I could replace just a sensor? I have a 2012. If just replacing the intake manifold will solve this issue, I'll probably just buy [URL] .... and replace it myself (assumable that's what I need ).
Prius (2001-03) :: Engine Runs Then Stalls / P3191 Code - Oil In Intake Manifold?
Looking at a 2003 Prius with 77K miles. Turn the key, the engine starts, runs smooth for about 5-7 seconds. After that it starts to run rough and rattle, then shuts off. The only code I pulled was P3191. I pulled off the air cleaner to clean the throttle body, and noticed a small pool of oil in the bottom of the intake manifold. Is that normal, or could that be causing the code issue? BTW, I cleaned the MAF and throttle body, and the engine still does the same thing.
View 14 RepliesFord - Windstar :: 1998 - Code P1538 For Intake Manifold Runner Control
I have 98 windstar, p1538 code, IMRC. I have physically checked both IMRC's and they are functioning as they should. (if they were bad, they would not move at all right?) Assuming they are good, which step in the troubleshooting process I go to now? The van runs perfect, just that darn light! Do I start going for the O2 sensor now? What to next in the chain of troubleshooting?
View 14 RepliesFord 6.7L Power Stroke Diesel :: CEL With Code P2074 - Cracked Intake Manifold?
I was chasing down a P2074 CEL and thought it was a stressed wiring harness connection on the MAF.
Took it to the Ford house and they chased it for 2 days, believing it was the MAF and air filter. They told me that air filter was allowing to much air in. My thoughts was, that is was what MAF is for, to regulate the fuel based on how much air was going in.
I just found out that they are stating that an AFE dry air filter contributed to a cracked intake manifold because the aftermarket air filter made the intake get too hot.
Sonata I45 (LF 2015+) :: Code P2006 Intake Manifold Runner Control Stuck On Closed
Check Engine Code P2006 intake manifold runner control stuck on closed? Taking it in to have it checked out.
View 10 RepliesGolf IV R32 :: Nozzle On Intake Manifold Broke
One of the nozzles on the back of my intake manifold broke off. I don't know how to better explain it. The ones the back of the manifold closest to the firewall there are several hoses that hook to the manifold. The second one from the left broke.
View 7 RepliesGolf IV R32 :: Intake Manifold Shifter Not Working
I'm having a problem with the intake manifold shifter not working on my r32. I've tried all of the normal fixes, the shifter rod itself and the vacuum diaphragm that opens it are both functioning correctly, all of the vacuum lines are new and not leaking. Connecting vacuum directly to the diaphragm causes the shifter to immediately open. I've tried 3 different solenoids with the same result, all open when 12v is directly applied, but the manifold doesn't open at it's RPM point like it's supposed to. The solenoid sees a constant ~11v under all conditions, regardless of engine RPM. I've traced this wire back to the ECU and confirmed it's not damaged. No CEL other than for the SAI missing.
At this point, I'm assuming whatever circuit that controls this in the ECU is fried (cruise control doesn't work either.) I have an extra 24v vr6 (2.8) ECU sitting around which from what I've read uses the same hardware, just a different flash. This may be a stupid question, but if I were to take this to UM to get a performance flash, would I be able to basically overwrite the 2.8 ECU and make this work in the R? Would there be any issues with the immobilizer?
Golf IV R32 :: Chamfering Noise From Intake Manifold On Idle
I have a chamfering noise coming from my intake manifold on idle. sometimes its there and sometimes its not, it goes away with any application of throttle.
View 9 RepliesGolf IV R32 :: Stock Intake Manifold Valve Broken?
I am just wondering at what revs the stock intake manifolds are meant to switch over as i think mine is stuck and not moving.
View 23 RepliesGolf/GTI VI :: Clicking Sound Coming From Intake Manifold?
I have a small clicking sound coming from my intake manifold. I recently installed a boost gauge and it did it once after that... I shut the car off and I didn't hear again until 1000 miles later and its back, why it would be clicking like this but its annoying
View 6 RepliesGolf IV R32 :: Valve Cover And Intake Manifold Torque Specs
I have to replace the valve cover gasket this weekend.
View 5 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Melted Air Intake Manifold Port - Code P0171 And P0174
Wife took truck out and turned around after going less then a mile, saying it was running very bad. We got this truck about two months ago at a state vehicle auction. It was a state used truck, 145,000 miles, 05 Ford F350, ext cab and 8' bed. Anyway at first I thought it was valve tap until research said an exhaust manifold. With a fog machine in rear exhaust pipe we confirmed it was leaking and replaced the exhaust manifold. Figured it was probably a good time to replace spark plugs too. Took truck for a ride and she still buck and farted.
Got a code machine and got P0171 and P0174. Couldn't find a vacuum leak, but your could hear the air being sucked in. went to local parts store, guys couldn't find leak, but they said truck sounded like a steam machine. today I made a homemade smoke machine and smoke came from air intake, figured the gaskets were bad. The pictures show what I saw when I took the gaskets off. The port that has melted is the same port were the exhaust manifold was leaking from. Am in deep "doo-doo". What caused this?
Golf IV / Jetta IV :: Rattle Coming From Back Of Engine Near Intake Manifold When Rev A Little
I have a 01 vr6 mk4 gti. When I bought the car I noticed a rattle but never paid mind to it. But now I just want it fixed. I hear the rattle come from the back of the engine near the intake manifold when I rev it a little. The most rpms the louder the rattle . I been doing some research and came to a conclusion that it could be the shift rod and bad intake bushing. But, I'll like a link on how to replace the shift rod.
View 5 RepliesGolf IV / Jetta IV :: 2003 - Air Shooting Type Noise Coming From Intake Manifold Valve?
It makes a weird 'fppp' air shooting noise before the exhaust note and my 2003 gti vr6 makes the exact same noise. It sounds like it's coming from the intake manifold valve and not really the filter, but I'm not sure and yes my filter is clean, the noise also sounds a little bit more obnoxious and problematic in real life. What it is, I thought it was a vacuum leak but I don't wanna bring it in till i know exactly what it is,
View 2 RepliesTiguan :: CEL Came On - Intake Manifold Sensor
Today I was on my way back home from a weekend trip to see family when the CEL came on. The car was running fine no problems (we had driven 200 miles). Gas mileage was good, good power, no weird noises, engine temp was fine (it was 100 degrees outside). But being how the car has 39k on it and its the most expensive thing I own; I pulled over and had autozone scan it for me. It came up as Intake Manifold Sensor. I have never worked on this car but Im going to at some point, I'll replace it myself if it isn't to hard. I am wondering if it is as simple as replacing the sensor or could there be an underlying issue like a blown intake manifold gasket (like i said the car was running fine though)?
View 6 Replies