Ford 6.7L Power Stroke Diesel :: CEL On For Code P20BA - Reductant Heater A Control Circuit Performance
Okay, so I have a 14' 6.7L, about 18,438 miles on it and the check engine light came on when I was at the gas station ready to leave, and so I took a field trip to auto zone and they scanned the CEL and it came back as P20BA - Reductant Heater 'A' Control Circuit Performance and they said I need to change out the pump assembly so I took it to the dealership and they cleared the code which worked for awhile, about 4 months ago the light came back on and I'm wonder if I should get the pump/heater changed out or get it deleted? The warranty is going to end in august this year..... It's been fine no issues with the truck, even tho I drive with the CEL on and just wondering what I should do? The CEL has been on for almost 5 months.
View 4 RepliesFord 6.7L Power Stroke Diesel :: 2012 - Code P061A / Internal Control Module Torque Performance
I have a 2012 6.7 with a Spartan tuner. Threw this code a few months ago. Reset everything, trucks runs great, no issues. Never had this code come up again. I've looked it up and it says, "Internal Control Module Torque Performance". I'm just not sure what this means.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Code P0404 - EGR Circuit Range / Performance
I keep getting a problem code of P0404 - EGR Circuit Range/Performance. What it is and if its a serious issue?
View 2 RepliesFord 6.7L Power Stroke Diesel :: CEL Code P263C For Glow Plug Driver Performance
CEL came on in my 2013 6.7L with 74K miles a couple days ago. Pulled the code today and it was a P263C - Glow Plug Driver Performance code. Any remedy for this.
View 8 RepliesFord 6.7L Power Stroke Diesel :: CEL On - Code P2043 - Reductant Temperature Sensor Range / Performance
My check engine light popped on for me a couple days ago. P2043-reductant temperature sensor range/performance. Truck still runs like a raped ape, no change in driveability. Just over 21k miles. No "speed limited to 55" messages or anything else. Basically no change in the truck other than the light.
View 12 RepliesFord 6.0L Power Stroke Diesel :: EGR Valve Control The Amount Of Exhaust Into Air Intake?
I understand that exhaust runs through the EGR. what I don't know is:
Does the EGR valve control the amount of exhaust into the air intake?
If so, does only the amount of exhaust let through the valve go through the EGR?
if so, if the EGR valve is closed then no exhaust will go through the EGR?
Ford 6.0L Power Stroke Diesel :: 2004 F250 - EGR Low Flow Code
I am driving a early 2004 F250 CCSB with a 6.0l. I have a Code that is for an EGR Low Flow. I have a Scan Gauge II that I have been using to try and determine why this is. I have replace the EGR Cooler (unrelated), the EGR valve, and the MAF.
My EVD and EVM are tracking. My IA1 reads a letter (B usually) and 3 numbers that are in the 6 to 900 range. My IA2 appears to read normal with atmospheric temps at start up and goes up and down IAW the EVD and EVM readings. My FIA (already programmed) reads outside temperature along with the overhead console. The EBP reading doesn't exist, it is blank.
Ford 6.0L Power Stroke Diesel :: Code For EGR Flow Restriction Cause Limp Mode?
I'm going to do a weld-in-plug delete in my RV in the next couple weeks, and its a crapshoot apparently if it'll throw a code. My immediate concern is I want to go on a trip right after, and I won't have time to fiddle about getting an SCT tuner to turn the code off. What I definitely don't want is a code for EGR flow restriction to eventually cause my motor to go into some kind of limp mode while I'm in the middle of a long drive. Is this possible?
View 14 RepliesFord 6.0L Power Stroke Diesel :: Sticking Turbo - EGR Insufficient Flow P0401 Code
The truck in question is a 2004 6.0L Excursion, stock original turbo, no tunes, and EGR cooler delete done 1 year ago. Scanned for codes and none were found except for EGR insufficient flow P0401 code which is due to the EGR cooler delete.
Upon startup (no issues there) the VGT reads 67-70, now once the truck goes to high idle to warm up (1150 or so RPM) the VGT slowing climbs to 85 and stays there. If I blimp the throttle or step on the brake it goes back to 67-70 at normal idle. This has been happening for a few months now on a regular basis. I have checked the MAP, BARO, and EBP readings at KOEO and they are all within 0.6 of each other (14.4-15.0). The EBP tube was checked and cleaned (no buildup present)..
Ford 6.7L Power Stroke Diesel :: CEL With Code P2074 - Cracked Intake Manifold?
I was chasing down a P2074 CEL and thought it was a stressed wiring harness connection on the MAF.
Took it to the Ford house and they chased it for 2 days, believing it was the MAF and air filter. They told me that air filter was allowing to much air in. My thoughts was, that is was what MAF is for, to regulate the fuel based on how much air was going in.
I just found out that they are stating that an AFE dry air filter contributed to a cracked intake manifold because the aftermarket air filter made the intake get too hot.
Ford 6.0L Power Stroke Diesel :: P0488 Code After Intake Elbow Install
Anyways, I've been doing a lot of work on my 6.0 2004 Ford Excursion lately, and recently installed my Sinister Diesel intercooler pipes and intake elbow, and had to remove my throttle body completely to do so. I know that the 2004 models throw codes when removed, and that's what I'm here for. Mine isn't dogged down and actually runs even smoother with my new piping and intake, but I want to get rid of this code.
Is there any tune out there that can erase it? For some reason my Edge Insight CTS2 sees the code, but my SCT X4 flash tuner doesn't see the P0488 code. I know people have discussed this topic several times, but after hours of reading through posts I never found any solution to this. All I need is a way to delete the code because I don't like having my CTS2 with a trouble code for something I did on purpose!
Ford 6.7L Power Stroke Diesel :: P2073 Code - Manifold Absolute Pressure / Mass Air Flow
My truck threw a P2073 code. Its Manifold Absolute Pressure/Mass Air Flow - Throttle Position Correlation at Idle. I do have aftermarket intake. It threw this code 2 weeks after install. Does this mean my mass air flow sensor is going to fail soon?
View 14 RepliesFord 6.7L Power Stroke Diesel :: 2015 F550 - CEL Code Oxygen Sensor Performance Bank One Sensor One
The service truck threw a CEL, and i pulled oxygen sensor performance bank one sensor one code. That would be driver side sensor between the manifold and cat, rite? Don't want to change the wrong one...
View 11 RepliesFord 6.0L Power Stroke Diesel :: Code P2290 - Injector Control Pressure Too Low
I just did a bunch of work on my 6.0. Here's a list- head gaskets, arp studs, new heads, 2 new injectors, updated stand pipes and dummy plugs, water pump, and all new injector o-rings. After messing around with a bent pushrod, cylinder 5 code and and replacing injectors the truck runs excellent. After driving it a bit I get a code "P2290 injector control pressure too low". The truck runs great with no low power, stalls, or hard start cold or hot. I do puff black smoke but that's because of the sct tuner on performance tune.
View 8 RepliesFord 6.7L Power Stroke Diesel :: DTC P207F / Reductant Quality Performance
It says "reductant quality performance". I was reduced to idle the other day at the boat launch, with my boat. Called roadside assistance to come get the truck. They said they weren't liable for my boat, had to call a friend to come get it. Bring the truck to the dealer and he blames it on the DEF I bought, non motorcraft. I purchased ford DEF, siphoned the old stuff out and refilled with the ford DEF. Went out of town on a fishing trip and got the CEL again.
View 14 RepliesFord 6.0L Power Stroke Diesel :: No Boost - P2290 Code For Low Injection Control Pressure
My 05 excursion died on me a couple weeks ago. First it threw a p2290 code for low injection control pressure. It did this a few months ago and had no problems. Cleared code and did not come back until now. So I cleared the code. Drove a few more miles and lost all boost pressure. Still fires up and runs. It does run a bit rough but only a little bit.
I replaced the oil cooler, did egr delete, and put an IPR remote oil cooler and full flow coolant filter on it few months ago. Since it died i pulled the ipr valve and it looked good. I put a new screen o-rings, and wiring pigtail on it since it was out. Put back together and still no boost. I really did not figure that would fix the boost issue but i wanted to make sure the screen was not clogged or torn.
Truck will fire up cold and warm with no problem and run. The hose from the map sensor to manifold is good and i put new clamps on it.
2005 6.0 with 95,000 miles.
ICP duty cycle = 0.29
map kpa = 102
Injection control pressure = 5.91 MPA
Ford 6.7L Power Stroke Diesel :: Chips And Tuners Addition For Fuel Performance?
What chips can I add for better fuel performance when pulling my 5ver ?
View 7 RepliesFord 6.0L Power Stroke Diesel :: CEL Comes On For Code P2287 - Intermittent Injection Pressure Control Circuit
2004 Excursion 6.0L .... Recently after a 200 mile trip through the mountains running good, I get home and the next day it idles down the driveway at a high idle and after a few minutes seems to run better but within 5 miles the CEL comes on and throws P2287 - intermittent injection pressure control circuit. I cleared the code, ran around town again and the light came on again same code. I'm getting appropriate ICP-voltage and pressure readings. I took it home sat overnight and thought I would pull the ICP sensor.
I replaced the ICP sensor less than 6 months/5,000 miles ago. I also changed out the main engine harness at the same time. I looked at ICP sensor and it looks clean. Started the truck and tried the scientific wiggle test while running and monitoring ICP-voltage. Started at the sensor bending and wiggling back to FICM. No fluctuation in voltage. Ran the truck around town, 20 miles and no light. Yesterday we made the same 200 mile trip over the mountains, seemed to run strong. In town this morning within 5 miles the CEL is back on and the only code is P2287.
My Ford powertrain diagnostics manual doesn't have the P2287 code in it for troubleshooting. Should I go after the FICM, and how do U test that if so? I'm currently that 200 mile drive from home and don't want to damage anything more.
Ford 6.0L Power Stroke Diesel :: Engine Light On And Code P2285 - Injector Control Pressure Sensor Circuit Low
Engine light came on yesterday and started missing on take offs. Giving code p2285 Injector Control Pressure Sensor Circuit Low. I've done the research and understand the problem. It's the weekend and shops closed until Monday. Is it safe to drive in the mean time? Is there any risk of doing damage? What's the risk of it quitting or failing start in the short term, today?
View 2 Replies