Ford Ranger / B-Series :: 2000 - Trans Won't Engage - 4R44E Shift Cable?
I bought a 2000 Ranger 4x4 3.0L auto today from the neighbor guy sight unseen with a "bad tranny" for $400. I'm very unfamiliar with the Ranger family, but long story short:
When moving the shift lever, the trans doesn't engage. It needs to be engaged from underneath. Do the cables tend to stretch, or break? I can't find any adjustment on it anywhere.
Ford Ranger / B-Series :: 1998 - 4r44e Transmission - Randomly Losing Power While Driving Like It Would Not Shift
Ok I've got this 98 Ranger with the 2.5L and the 4r44e automatic. The engine is used and has about 100,000 miles now and is it a good state of tune - so I think. The transmission was a remanufactured I bought a few years ago that was built with the shift improver kit, Kevlar bands, extra planetaries, 4wd pan, and external cooler. It's now got 92,000 miles on it and it's been serviced every 30,000 with a fresh 4wd filter and Mercon V fluid. It's outlasted the last 3 transmission I've had in my Ranger. I've got 315,000 miles on the body. For awhile it was randomly losing power while driving like it wouldn't shift, almost like it dropped a couple cylinders, then as you kept your foot on the gas it would recover and rev up and shift.
Then sometimes randomly at stoplights it would shake at a stop and have no power at take off until it hits 30-40 mph. Sounds like a converter, is what I thought. But now it's doing it more often but not the shaking at stoplights as much as randomly losing power while driving normal speeds. Last night I drove it about 50 miles after doing a fresh filter and fluid change and this time it did it so much it threw a code up P1131. Even though that's a O2 sensor code, could it be hidden by a transmission valve body problem? One transmission shop said it could be a valve hanging up just by me describing it to him. Could this be ignition or fuel related or is it all tied in with the transmission problem, if it is even a transmission problem?
Ford Ranger / B-Series :: 2004 - Hard To Shift Into Low Gear
It's a 4 cylinder 5 speed, and once or twice a day when the light turns green and I go to put it in low gear, it just doesn't want to go into gear easy. It's like the syncro isn't happy or something. The clutch is depressed all the way and not dragging.
View 14 RepliesFord Ranger / B-Series :: 2000 - 4WD Hard To Shift
2000 ranger 3.0 auto 4wd hard to shift. Are the cables known to stretch?
View 6 RepliesFord Ranger / B-Series :: 1999 - Hard To Shift Smoothly Into Third Gear
I have a 1999 ford ranger 4x4 with automatic 5r55e and it had problems shifting smoothly into third gear. I changes the valve body gaskets and the (rooster comb) detent lever. Now it shifts very hard and has on first second and passing gear.
View 6 RepliesFord Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Ford Ranger / B-Series :: 2000 - ABS Light / No Speedometer And Transmission Doesn't Want To Shift
Sold my mazda and got a nice 2000 2wd Ranger XLT with a 3.0L. Today the wife I and took it to town, 10 miles on the highway there, a couple in town and 10 back, didn't notice anything unusual. However I haven't this truck long so I'm not sure what is usual.
Parked it for a few hours and when went out to change the front turn signals to LED I noticed the ABS light was on when I drove it into the garage...
I checked fluid, connections and fuses, no change.I go ahead and swapped the bulbs while letting things simmer, I've had so many of these Fords sometimes the easy fix comes to me.
I backed it out and took it down the road, right away I noticed my speedometer wasn't working, so I let off the gas, when I re-applied the pedal I got nothing, like it was in neutral.
I downshifted to second and got her down and turned around as the O/D started flashing... (so glad because I would have hated walking back), then pulled her back in the garage to check transmission fluid and recheck fuses, including the ones I forgot earlier under the hood. I added a 1/4 qt of fluid then tried a road test again, this time there was a real long pause before it upshifted hard and the CEL came on.
I pulled the codes with my scangauge and got:
P0500
P2120
P0028
And decided I better look some things up and consult the gurus here before I do anymore damage tonight. I'm guessing that I'm looking at a tranny replacement possibly, but with the ABS light and speedometer failure I'm not 100% sure what is going on here...
Ford Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesFord - Focus :: 2001 - Brake Pedal Feels Hard / Transmission Hard To Shift From 1st To 2nd Gear
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
Ford Ranger / B-Series :: 2003 - Hard To Shift After It Warms Up
I bought a 2003 Ford Ranger, 2.3, 5 speed manual. It is hard to shift after it warms up. I test drove it when it was below freezing, so I didn't notice it at first. The warmer the day and quicker the truck warms up, the worse it is. It goes into gear with no problem when the engine is off or if I'm still moving, but if I'm stopped there are times it is hard to get into gear. This really sounded like a clutch that wasn't fully disengaging to me, so I decided to pull it apart. I didn't check the movement at the slave before I started, but I did find the master was a little wet at the rod in the cab.
So, I did the following:
- New clutch master cylinder (system bled out of truck to eliminate air)
- New slave cylinder and bearing
- New pilot bearing
- Changed transmission fluid - Mercon III ATF
I inspected the clutch/pressure plate and it was in good shape and looked like it might have had 10K - 20K miles on it. The last owner said it was recently replaced and it looked it. So, I put it back in. After I was done, I checked the movement at the slave/pressure plate and it is moving about 3/8" - 1/2" when the pedal is down. I was happy and thought this would solve the problem since the old pilot bearing seemed stiff and I saw the leak on the back of the master cylinder.
I drove it and all felt fine at first, but it was a cool day and I didn't drive it that long. When it was warmer over the next couple of days, it started getting hard to shift again. It's not been quite as bad as before, but still doesn't shift right.
Ford Ranger / B-Series :: 2002 - Hard To Shift Gears
I have a 2002 ford ranger edge. swb, 3.0L, 5spd. I have been noticing it is getting harder to shift gears, put in 1st at a stop light lately. There is no grinding just seems harder to engage. Checked fluid level and it is clean and full. Recently i have developed a vibration under power. Let off the gas and smooth as can be, apply throttle and starts vibrating. Not sure if flywheel is "hot spotted" or perhaps broke a spring on pressure disk. Just seems odd it's only under throttle. Yes already checked rear end and U-joints.
View 2 RepliesFord Ranger / B-Series :: Won't Shift Into 5th Gear?
ive been experiancing an issue with my trucks shifting. it shifts smoothly but doesnt like shift into 5th, as im driving it stays in 4th longer than necessary. my thought was that it was tied to a shift sensor, what do you think?
View 5 RepliesFord Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Ford Ranger / B-Series :: 1993 Manual Trans / Hard To Shift Into First
I'm having a little issue with shifting into first. Once in a while it simply will not go in, like you're pushing the shifter against a brick wall. If I turn off the truck and turn it back on, it works absolutely fine. I can shift into 2nd-5th no problem at all times. Is it just the shift linkage, or...? I'm not really sure where to start.
View 7 RepliesFord Ranger / B-Series :: OD Off Light Flashing - Hard To Shift In 2nd And When Downshift
I have a 99 Ranger, 3.0 xlt 2WD Automatic 5r55e(???) tranny (i know its the 5). I have the o/d off light flashing. It comes on when fluid gets to op temp. When on it shifts hard into 2nd and hard when it downshifts. No slipping. I have had the truck in the tranny shop for 3 weeks, owner said he re built valve body gasket (didnt work) tried 3 diff used tranny's (didn't work) or so he says. He said it needs to be rebuilt.
I have searched up and down for what it could be, there is so much out there, it only confused me more. If i have to rebuild i will, i think the tranny shop was pulling my leg (for more reasons than mentioned). I have a check engine light on nothing to do with tranny...there is a tranny code, he would not tell me but i will have it checked. Been told could be throttle position sensorl, speed sensor cracked case and a million other things. I have some mechanical abilities, (not too much w/ tranny's) but i can change a few simple sensors.
Ford Ranger / B-Series :: Column Shifter Too Hard To Shift Through Gears?
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
Ford Ranger / B-Series :: 1999 - Trans Won't Shift Into Any Gear
i have a 1999 mazda troy lee b3000. The truck has a 3.0 flex fuel and 4r44e and when you go to drive it. turn the key engine fires up but the trans won't shift into gear. Here is the back story.Bought the truck brand new in 99 I'm the original owner it was a daily driver up until 2 years ago. the truck has over 300k miles and still ran great but the camshaft was starting to go. I was gona replace the cam but came across a killer deal on a new engine. picked up another 3.0 flex fuel with 50k miles. drove the truck into my garage removed the old engine installed the new engine. got in the truck turned the key and the new engine roared to life.
I went to put the truck into gear so i could get it out of the garage and go for a test drive and nothing. went to put it in drive and again nothing. no matter what gear its put in it doesn't move at this point i was confused and decided to quit for the night. That was in 2011 its now 2013 the truck has just sat there sense then. I've tried anything and everything even went as far as swapping transmissions and computers with no luck. I took the trans apart I don't know how many times can't find anything wrong with it.
Ford Ranger / B-Series :: 2003 - Sluggish To Shift Into 2nd Gear?
2003 3.0 FFV 5 speed automatic...... Just noticed recently that it seems slow to go into 2nd gear.....the rest of the shifts seem fine, firm and unchanged.....
View 4 RepliesFord Ranger / B-Series :: 1998 - Gear Shift Indicator Is Wrong
98 Ranger 4x4 4.0 L Supercab. Today I replaced my instrument cluster lights. When I put everything back together i noticed my gear shift indicator is off and I cant shift into 1st or 2nd. What did I screw up?
View 5 Replies