Prius (2001-03) :: Warning Light Came On / Random Engine Misfire - Code P0300
Had this code show up after the warning light came on and then the light went away after two day, the car seems to be a little sluggish now. I have read that this is a random engine misfire and it could be a bad plug..
View 1 RepliesYaris/Scion & Vitz :: P0300 Random Cylinder Misfire - Check Engine Light Randomly Comes And Goes
The check engine light keeps coming on and off on my 2001 Echo with the above code. The car runs fine and the check engine light randomly comes and goes. What would set off the check engine light, but not cause noticeable change in performance?
View 2 RepliesAccent MC (2006-11) :: 2007 GLS - Random / Multiple Misfire And Code P0300
I have a 2007 Hyundai Accent GLS. I just got it from a used car dealership (local) and it runs perfectly. It had a misfire code when i first got it, for all cylinders plus the p0300. It went away when i started the engine again, and didnt come back til a month later (Now). now it wont go away.
I went to advance auto and had them use their OBD2 reader for a trouble code and i got p0300, p0301, p0303, p0304. No other codes present.
I am not feeling anything bad, and from what I am told, a misfire feels like a hard shift. This is of course after getting the plugs and wires changes as well as an oil change. Standard preventative maintenance.
The mechanic used OEM parts got from local parts shop. i think the OEM plugs are the copper ones. I would have preferred iridium as they arent that much more expensive but I don't want to pay for another plug change.
The only symptoms I can think of, is that according to google, I should get around 380 miles to a full tank (11.9 capacity, 32 mpg city). I am only getting 280 from full tank to gas light.
I have also gone through a lot of oil. I checked the dipstick and it was below the low line, so i bought a quart of high mileage oil (same exact brand and type of oil that i gave to the mechanic to use) and it went to just above the full line. This was at around 1500 miles after oil change.
After visiting multiple sites about misfires, i found a few things that caught my attention. One is a site called auto service professional, which talks about the OCV for the MC accent. A lot of sites also recommend gaping the plugs at .035.
Lexus GS 2006-11 :: Check VSC Error Code P0300 With Check Engine And Traction Light On
A few days ago my "Check VSC" warning came on along with the check engine and traction lights being on. I left my car in a parking garage for a week when I was on vacation and the lights came on once I started the car after getting back from my trip.
I have had the "Check VSC" warning before and I fixed it by replacing my gas cap. My gas cap seems fine this time around so I got my codes scanned and the only one that came up was P0300. Having this issue with the 2007 Lexus GS 350? I still feel like it's my gas cap because I bought a cheap replacement last time around.
Dodge - Durango :: 2003 - Code P0300 Random Misfire / Engine Running Rough
Just started getting a p0300 random misfire code on the durango a couple days ago. pretty sure it isn't moisture related since it started on a nice sunny day. it was running pretty rough so it was obvious that it was misfiring. I changed the plugs since it was about time anyway, and they needed it and I cleared the codes. new plugs (put in the oem champion copper plugs) didn't make the problem go away. The engine still ran rough and the code came back. 2 of the plugs looked like they may have been fouling a little bit. they were a fair bit blacker than the rest of the plugs. I went ahead and changed the coils on those two cylinders and reset the codes again. Still runs rough and the p0300 came back. where do I go from here? I am not getting any specific cylinder codes so it makes sense to me that it isn't one or two cylinders not getting spark. 2003 durango 4.7 ....
View 6 RepliesElantra XD (2001-06) :: Check Engine Light Will Pop On Occasionally And Code Reads Random Misfire
2004 Elantra AT ... 6 months ago top of the radiator cracked caused it to overheat and blow the head gasket and warp the head. Repaired that and compression is fine now. It ran great for 4 months but now it randomly stalls. at or near idle. Seems to do it more at operating temp rather then cold. Occasionally the check engine light will pop on and the code reads (random misfire). It acts just like it has been shut off. But immediately restarts.
View 3 RepliesFord - F150 :: Check Engine Light Started Flashing / Cylinder 4 Misfire Code
1997 Ford F150 - 133K Miles - 6cyl - 4.2L. This is a truck that gets less than 2K/year put on it. Has had "issues" with worn bearings and holding oil pressure for a few years now. Yesterday, the check engine light started flashing (as opposed to solidly lit) and the code came back as a cylinder #4 misfire (only the one code). The truck was clearly not firing on all cylinders and at idle, ran terribly (couldn't be driven). I just did a compression test on all the cylinders and all measured around 140-145psi except the #4 which read almost 170psi. I rechecked this a few times as well as a couple of the others and am now sure of the results. What could cause this one cylinder to have a higher compression ? Is whatever is causing this increase in the compression, also be the cause of them misfire ?? I'm stumped here and quite frankly, expected the compression on the #4 cylinder to be really low as opposed to the others.
View 13 RepliesTrailBlazer :: Random Misfire And Code P0300 - Rough Idle
'02 TB w/ code P0300 / Random misfire. Started the other day when it was very damp out, FWIW. Feels like ur driving on rumble strips during acceleration. Rough idle also. It does not do this continually though as after a while (minute) it clears up and runs smooth for a while then runs rough & light will again for a while. I seafoamed it today since it been about 60k since last seafoam. I thought that might have worked until I drove about 20 mile and it went rough again. I also cleaned the oil out of the cam sensor elect connector, since that caused rough running before, although it didn't throw that code. It seems to be very intermittent. '02 TB, 185k miles, orig plugs changed at 125k. Is it actually just going in & out of a limp-mode? O2 since it's random ???
View 14 RepliesPrius (Gen 2) :: P0300 Code And Random Misfire - Car Shaking More Than Usual
Recently i started the car and it was shaking more that usual. the CEL light came stating P0300 with random misfires. It sounds and feels like misfires so i believe this is true.
View 10 RepliesGMC - Sierra :: 2004 - Code P0300 Random Misfire While Under Load
2004 GMC Sierra 2500 HD, 227,000 miles 6.0L V8.
While driving up hills or increasing load, the CEL will flash multiple times, I pull over as I know CEL flashing is not good. I turn the truck off, allow it to sit for a few minutes, whip out the code scanner, only code that was there happens to be P0300. Truck has poor MPGS, idles rough, loss of power. this happens every time I drive this vehicle as I use this truck to pull my trailer that weighs around 4000 lbs. Problems come and go. Some days I can drive the truck for an hour with no problems, come up to a red-light, BAM, CEL is flashing, truck is bouncing side to side due to the poor idle, other days this happens while sitting in the parking lot of my job with the ac on.
Truck has been to the shop several times as I'm no mechanic. Parts replaced are as follows:
- Fuel pump
- Throttle Body
- All plugs
- All wires-All Coils
- Intake Manifold Gasket-
- Battery
- Sensor 1 Bank 1 O2 Sensor
- Sensor 1 Bank 2 O2 sensor
Santa FE SM (2001-06) :: 2004 3.5L V6 - Random Misfire Code P0300
I have a 2004 Hyundai Santa Fe 3.5L V6 when i was driving a couple of days ago the check engine light flashed and after a while it stayed on the codes are P0300 which is a random misfire as well as a misfire in cylinder 2, 4 and 6
I replaced all 6 spark plugs and the 3 spark plug wires still the same issue. The car hesitates when accelerating when i accelerate it looks like it wants to stop the rpm goes to almost zero and then it moves and so on. the rpm goes up and down like crazy.
Sometimes it won't move past 1000 rpm I'm moving 60mph and still on 1000rpm and sometimes it works just fine like there is no issue at all. When idle the car is fine and everything seems normal it stays on 900rpm. The car has 158K miles on it.
I uploaded a video to show you what's happening to the tachometer when I accelerate [URL] ....
I'm on a limited budget I'm thinking of changing the ignition coils but i want to make sure that's what is causing the problem first because i spent 200$ to change spark plugs and wires and the mechanic didn't fix the issue.
Impala - Chevrolet :: 2000 3.8L V6 - Code P0300 Multiple Random Misfire
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
Chevrolet - Avalanche :: 2003 - P0300 Code / Multiple Or Random Misfire?
My 03 Chev Avalanche is giving me a P0300 code (multiple or random misfire). With no distributor or individual coil is this something I can fix myself or is it shop time?
View 6 RepliesPassat (B5) :: Flashing Check Engine Light / Codes P0300 And P0301
This morning I started my car and it was idling a little rough. The the Check Engine light began flashing - I immediately turned off the car and consulted this forum and my father the mechanic. After talking with my Dad and telling him that the car had sat for a week, he thought the issue was probably NOT the catalytic converter and thought it was probably related to the car sitting and possibly getting moisture in the gas. I started the car again (the roughness at idle seemed to have gone away) but the check engine light/malfunction indicator light (MIL) did not flash, it did come back on after a few seconds, but as a solid light . And as we've all read, it's OK to drive with a solid MIL.
I took the car over to Autozone and had the codes checked - P0300 (multiple cylinder miss fire) and P0301 (cylinder 1 misfire). I asked them to clear the codes. I has just put in new NGK spark plugs last month, so I didn't think it would be the plugs. I looked at a new coil pack for one of the cylinders. I decided to see if clearing the codes alone would work and drove home. No issues so far, no MIL, no rough idle, no hesitation (fingers crossed).
When I called the stearleship - they recommended I have the car towed, but would not speculate as to what the flashing MIL could be (catalytic converter or bad coil pack(s))...
Ford Super Duty (1999-2016) :: P0300 Code And Various Misfire Codes For Random Cylinders
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
Sonata NF (2006-10) :: Check Engine Light Flashing / Stall
Earlier today i left my car idling for a couple of minutes and when i got back in and started to drive the car was vibrating, almost as if it was going to stall and the check engine light was flashing. drove a bit and stopped, started the car and now the check engine light stays on constantly. I have had the light come on (and remain on) a few times in the last while but it is usually solved by tightening the gas cap. it always seems to happen when i am low on gas (100 mile range-ish) Someone suggested maybe i had dirty gas in the car and needed stabilizer. My boyfriend said its a "misfire" and to change the spark plugs.
View 9 RepliesSonata NF (2006-10) :: 2007 - Check Engine Light Flashing
I have had this issue on and off for a while. happened about 2 years ago just after i bought the car, and just started last week again.
The car will be running fine, then will start to buck while accelerating, shortly after the check engine light will start flashing and the car runs like it is on 1 cylinder. shut of and start again, light remains on( not flashing), car runs smoother, but does not accelerate like it should.
took it to autozone, they said it was giving the code for random mis-fire, and O2 sensor.
2 years ago the dealer said it was loose coils, and they fixed the problem, all the coils feel tight this time.
2007 Sonata ... 3.3 V6, 70k
Sonata NF (2006-10) :: Tensioner And Check Engine Light Flashing
My Sonata has 150k on it and the tensioners have gone bad 3 months now. This AM i got a flashing check eng. light and the car runs rough. Any relation or am I looking at plugs or coil issues?
View 9 RepliesCorolla :: 2011 - Check Engine Light On / Random Misfire
I have a 2001 corolla with 37K mi on it. The check engine light came on today. Took it to advance auto parts to read the code. It showed P0171 (System too Lean) and P0300 (Random Misfire). Called up a toyota dealer and the technician think it might be bad gas. I buy gas at name brand gas stations and sometimes from BJs. I am not sure if the problem is with gas. I also been up to date with maintenance.
View 14 Replies