Ford 6.0L Power Stroke Diesel :: Transmission Slammed Hard Into First Gear And Sometimes Will Not Upshift
Everything was fine, running PHP 200X tune, switched to PHP 65 tow and took the 5er toy hauler on vacation last month. Pulled a lot of mountains,etc. While camping, took the truck unloaded to get fuel. Engaged tow/haul going down a mountain to utilize engine braking and the tunes "exhaust brake" and the trans slammed HARD into first gear. This happened twice. I refrained from using tow/haul. Heading home 450 miles with the 5er, I utilized tow/haul again (had it on the whole time, just like on the way down) and the truck and trans were flawless. Get home, switch back to 200X, and I'd say within a week or so, began having trans issues. Loaded stock tune, reset KAM with SCT, disconnected batteries with headlight switch on for a couple days, reloaded 200X and drove it for a couple days. No change.
It felt like the trans was slipping, not "going" like it should when on the throttle, and would sometimes not want to upshift. It would just act "weird". This would usually occur under 40 - 70% throttle (I rarely ever get on it more than that), but sometimes less. Never got any check engine light or tow/haul flashing.
So today I finally did what I should have weeks ago, took off work and ran the truck to a shop.
- First the tech hooked it up to the scanner. No codes.
- Test drove it. He said it drove fine for him. It was fine for me as well, driving it from my house to the shop (I didn't "get on" the throttle though).
- He monitored the voltage from the trans temp sensor. He said the voltage was fine, didn't spike or do anything crazy. He didn't seem 100% positive on this but, said it starts out at 5V cold and voltage should drop as the temp increases, which it did. However, the temp started out at 300 and then dropped to 200 as he was driving. #1 the temp isn't (shouldn't be) that high, and #2 it should increase while driving not drop. The temp shown on my Torque Pro app hit 149 on the way to the shop and 168 on the way home (90 degrees outside). So he seemed to think there was something screwy there.
- While driving it, his scanner showed a trans overheat (over temp/high temp, whatever) code, but no check engine light or tow/haul flash.
- Drove it home. Trans was fine until I got on it a bit and then it acted funny again. But just driving normal with light throttle it is fine.
* Thinking about trying a new temp sensor.
* Could it be in limp mode which is why it feels like it is slipping, i.e. doesn't have the normal power I'm used to?
* When the tow/haul light flashes, is it the tow/haul light on the instrument cluster? That's the only thing that lights up when I'm in T/H. Where you push the button never lights up. Assumed it was just white lettering and not a light.
Ford Transmission :: 1967 F250 - Clanging Noise And Popping Feel When Clutch Engages
I recently changed the clutch in my 1967 F 250, all was golden. This was about 5 months ago , just the other day when going from 2nd to 3rd gear there is a clang and popping feel. the truck was making similar noises before the clutch blew out causing me to change it last time.
View 1 RepliesFord - F250 :: 1992 - Truck Will Shudder While Let Out The Clutch In First Gear
They are about my F250. It is a 92 with 186000 miles. I love this truck.
After a long trip, maybe 1.5 hours, the truck will shudder while I let out the clutch in first gear. This only occurs in first, and it doesn't happen after the truck sits for a bit, just after driving.
I have an opportunity for a good deal on a F150. It is a 2001 with 181,000 miles for $4000. Is it worth updating for the new technology even if there is the same old high mileage issue?
Ford Transmission :: 1997 F250 - Shifts Very Hard And Sometimes Feel Like It Slips Out Of Gear
My 1997 F250 Heavy duty shifts very hard and sometimes feel like it slips out of gear (i press the gas pedal to the floor and speedometer rises very slow and truck doesn't move like it should.
View 14 RepliesFord Transmission :: 4r70w - 4th Gear Shudder While Decelerating?
I just put a rebuilt 4r70w in my '97 expedition and it shifts good but in 4th gear when I let off of the accelerator it starts to shudder until it shifts to 3rd. It acts like it is freewheeling then catches on and off. My thoughts so far is that I don't have the digital transmission range sensor positioned right or the overdrive servo isn't working properly.
View 1 RepliesLexus RX 2004-09 :: Transmission Slip / Shudder When Shifting From 2nd To 3rd Gear
I have 142k miles on my 2005 RX330 AWD. This week I can feel the transmission slip/shudder when shifting from 2nd to 3rd gear.
My local transmission guy is pretty reasonable but like most salesmen he's going to say rebuild it the entire transmission in lou of something less invasive.
Ford Transmission :: E40D - Rough Shifting From 1 To 2 Gear / Whole Truck Shudder
My 1992 F-250 7.3 4X4 has a very intermittent issue with the E40D. Rarely, usually after a lot of around town driving (I don't know if that has any direct correlation), I will get a rough shift from 1-2. It will kind of bang into gear and make the whole truck shudder.
On one of it's episodes, it also did it in 2-3, however that only happened once and I haven't been able to make it do that again. I'm worried that it's something that I should address, if I can do so without just rebuilding the whole transmission. It doesn't slip and shifts fine most of the time, other than the occasional 1-2 issue.
To cut this short, does this sound like a 1-2 accumulator issue? Maybe just old truck syndrome? I feel like this is a dumb as hell question, but isn't it a bad idea to install a shift kit in an E40D with 126K miles on it?
Ford 6.7L Power Stroke Diesel :: Transmission Shudder When Push The Throttle In 2nd / 3rd Gear
I have already logged 6K miles on her, crazy, but it's my job. I have pulled 5 maybe 6 trailers (form trailers, about 15K pounds loaded, this time of year). Loaded or unloaded, when I push the throttle in 2nd, 3rd gear, I feel a shudder, like transmission shudder.I know this thing throws down 800 ft. lbs. of torque, should I not be pushing it so hard? Or, what am I feeling?
View 14 RepliesNissan - Frontier :: 2005 - Manual Transmission Shift Shudder After Towing
I have a 2005 Nissan Frontier with a manual transmission (~6500 pound towing capacity). I rented a large wood chipper this weekend. On the ride home from the rental pickup, the transmission started shuddering when shifting. It is most noticeable when shifting into first gear from a standstill, and less noticeable on each successive shift. Once the gear is fully engaged, there is no shudder - it is only when letting out the clutch that there is the shudder. The truck only has 50k miles on it.
View 14 RepliesGmc - Jimmy :: 1997 - Transmission Rebuilt / Grinding Sound When Slammed Into 4WD
I drive a 1997 GMC Jimmy, with 250k miles (all mine). So, I had to have my transmission rebuilt, and the second time I picked it up (we won't talk about the first time) I drove it for a couple of days, and was leaving an icy parking lot, and put it in 4hi. I had it in gear at the time, but wasn't moving at all, and simply pushed the button. It made a grinding sound, then slammed into 4wd. I dropped it off the next day (again), and was told that I cannot put it into 4hi on the fly, that I shouldn't be doing that at all, that when you have a transmission rebuilt, you shouldn't ever do that again.
Given all of the trouble I've had with this highly advertised local transmission shop, I'm not inclined to believe a thing they say- So, I'm asking you all; When I had my transmission rebuilt, did I in fact lose the ability to put into 4hi while vehicle is in gear- let alone moving? I'm not talking about 4lo here, I know I have to be completely stopped and in neutral for that, even my manual says I can go into 4hi safely up to speeds of 45 mph. I still haven't picked it up from the last time I took it in, I didn't have any trouble with 4wd before the transmission rebuild. The first time I picked it up, my driveshaft fell out.
Celica :: Clutch / Transmission Rattling When In Gear
I have a 2001 Celica GT with about 140k miles on it and a manual tranny.
Over the last couple months, the clutch or transmission has been making a weird rattling sound when in gear. It's mostly while not accelerating, and it's not a consistent rattle - kinda like something is loose in there. It's not super loud, just barely and annoyingly noticeable. When the clutch is in and you just rev the engine there is no noise. Driving down the road if you put the clutch in and coast there is no noise.
I recently checked the transmission oil. Oil level was fine, but it was smelly as heck, so I replaced it. No bits or metal or anything in the oil.
The clutch in the car has never been replaced and is on its way out - I'm just wondering if its worth it to repair the car. I took it to a local Toyota shop and they thought the transmission needed replacement. This was the same shop that diagnosed my spun rod bearing as a valve issue, so I'm kinda skeptical
Golf IV R32 :: Clutch Feel Like Tighter?
I have had some weird feelings in my clutch after I launch my R hard, it feels like the clutch is tighter and has a different feel to it than with normal driving. car is stock for the most point and fairly new to me so I am not sure if anything has been replaced clutch wise. What the problem might be?
View 3 RepliesFord Transmission :: No Clutch / Truck Will Not Engage A Gear While Running
I have a 2001 m5r2 ford f-150 standard transmission. i have replaced the slave cyl., the entire clutch assy., the master cyl. pilot bearing. the trans. will engage all five gears plus reverse while truck is off but will not engage a gear while running. i have bled and bled and bled and still will not engage.
View 1 RepliesGolf/GTI VI :: Mushy Clutch Feel - Slipping In High Gears?
I've just about had it with this car:
- Car always had a "mushy" clutch feel. Not proper pushback against your foot feel.
- brought in several times under warranty, all was fine (documented by several dealers) from Jun- November 2015.
- Clutch then goes out at 52k, slipping in high gears. Dealer noted the pressure plate was blackened/burnt. June 2016
- I replace clutch at dealer, $1700 later. Pressure plate, slave cylinder, clutch disc, resurfaced flywheel. Pedal feel is awesome for about a month. Pedal "mush" comes back 1000 miles later. July 2016
- Take it in under the 12k warranty again, and they replace clutch master cylinder. It's about 60% better, but pedal will lose pressure occasionally and at higher altitudes (over 4000 feet) July 2016
What else haven't I replaced? And would a failed clutch master cylinder cause premature clutch wear if not replaced for months?
Ford Ranger / B-Series :: 1986 - Transmission Overhaul - Hard To Get Clutch Into Gear From Neutral
Rebuild on the Mazda 5 speed transmission. My 1986 Ranger 2.3 Four cylinder has 280,000 miles and the clutch has never been replaced. It's not slipping but I'm having trouble getting it into gear from neutral. Was told that the release springs on the clutch plate have weakened causing the clutch to not release completely so figured it's time to replace it. It's done well the last 280,000 miles. The question I have : overhauling on one of these Mazda trans and how difficult was it. Any special tools required, etc...I see Autozone has a rebuild kit which appears to have bearings, seals and gaskets. Figured while it was out I would go ahead and rebuild it myself if I can. Rebuilt a few engines but never touched a trans.
View 4 RepliesGolf VI R :: Slight Gritty Feel Or Like Rubbing Against Sandpaper When Lift Up The Clutch
I have a Mk VII R manual transmission with only 500 miles on it, but I'm having an issue that I think some of you may have experienced. My clutch is perfectly smooth when idling or in neutral, but there is a slight "gritty" feel or like rubbing against sandpaper when I lift up the clutch, mostly in 1st or 2nd gear and just when I give it throttle and the car starts moving or when the clutch engages. I thought maybe I was crazy but I did a search and found multiple people with this same issue on the MK VI R's.
[URL] ....
And this one: [URL] ....
I've got 500 miles now, so I'm going to wait until 1000 to bring it to the dealer.
Ford - Ranger :: 1995 - Clutch Does Not Engage / Pedal Starts To Feel A Little Spongy
I have a 1995 Ford Ranger 4 cyl w/ hydraulic clutch, about 95k miles, and an intermittent problem. Normally, my clutch works fine, but a few times a year, normally during the summer, and normally only after driving for a half hour or more, it starts to act up. First, the pedal starts to feel a little spongy. Then, I'll depress the clutch, and when I release it, the peddle comes up, but the clutch does not engage; a few seconds later, the clutch engages fully instantaneously, which usually stalls the engine if I am stopped.
Then, when I try to reengage the clutch so that I can restart the engine, the clutch is very stiff, and I have to pump it a few times, at which time it will depress easily, and then I am usually back to the original problem where the peddle comes up but the clutch does not engage. When I finally make it home and the truck sits for awhile, the clutch then works fine again. I think it is the orig clutch. I have talked to several mechanics about this problem (including the Ford garage!), and they are mystified. One mechanic thinks that it is a problem with the master and slave cylinder combo, and can replace them.
Gti - Volkswagen :: 2003 - Shudder While Shifting To 3rd Gear - Smaller Shudder Shifting To 4th
I had recently purchased a 2003 golf gti AUTOMATIC (with optional shifter) with a 1.8 turbo 4 cylinder engine. The vehicle has 139,000 miles on it. Before purchasing, I had a mechanic come out and look at the vehicle for a pre-purchase inspection, and ran the code P0303 (cylinder 3 misfire) which without test driving, told me that is what caused the shift shudder I noticed when I had test driven it a previous day. He told me the coil packs were in good condition by looking at the top of them, and told me if I replace the spark plugs, the issue should go away.
I feel it is important to mention that he had also run codes on the transmission and nothing came up. Taking it home, this morning I had replaced the spark plugs and driven it for about an hour both regularly and aggressively to test it. The problem is still there, and I was really hoping that there is a solution to this problem, because everything else on the car is beautiful, while being my dream car, I just want it to work as well as I know it can. To be more descriptive, when shifting to 3rd the whole car feels basically like it is tripping over itself before successfully shifting.
Ford Aerostar :: 1988 - Clutch Feel Grabby / Some Sludge Accumulation Between Trans And Engine
I've got an oddball '88 SWB with the M5OD transmission. Since I've had it (about a year now), its always required a lot of gas to get it rolling without it stalling after sitting overnight or during the day at work, especially putting it in reverse for the first time. The shifts have always been a little choppy/jerky/grabby/whatever you want to call it, too. Mostly going into first from a stop, but you can feel it other gears too, especially if you're not flooring it.
Anyway, it seems to have gotten worse and I'm getting to the point where I'm looking at a cause. One thought I had was oil contamination on the clutch discs, I know this will make a clutch feel "grabby". There is some sludge accumulation between the trans and engine, and it appears I may have a very slow leak there.
I have to change the trans fluid this weekend and am wondering if there's anything I should inspect while I'm at it -- I don't know a whole lot about the clutch system on this van and there's next to no information on it. Frankly, I don't even know if its hydraulic or cable.