Ford Super Duty (1999-2016) :: Front Hubs Not Auto Locking
My hubs will not lock when put into 4x4. I disconnected all lines from the solenoid to both hubs and tested them for leaks... All good there. I put a gauge on the lines at both hubs one at a time while the other is still connected and get no reading when switched into 4x4. I checked for vacuum right out of the solenoid, and I get 2inHg when switched into 4x.
The vacuum pump kicks on every time I start the truck, even if I just shut it off and re-start right away. There is no delay when switching my ac/heater controls to different settings or vent locations. So I know there is vacuum. How much vacuum I should be getting out of the solenoid to the hubs?
2004 F350 6.0L....
Ford Super Duty (1999-2016) :: 2006 6.0 F350 4x4 Auto Hubs Will Not Engage
I was using 4x4 High the other day and it was working just fine. Now today, I was at my first parking lot to plow and used the ESOF to shift into 4x4 High and it did not engage with the hubs being in auto mode. The lights on the dash show up indicating that I am, but I am still in 2wd.
If I manually lock the hubs, it engages 4wd high. I tried the same thing using the ESOF to switch over to 4x4 low and it does NOT engage either.
I also noticed that heater blower was switching over to full defrost even though I had it set on the floor setting (manual heat climate *****).
Does this sound like a vacuum leak? I haven't had a chance to test the lines yet. Btw, this is my second work truck and not the one listed in my signature below. It's a 2006 f-350 6.0 xlt.
Ford Super Duty (1999-2016) :: Clunking In Front End When Turning Hard Even With Hubs In Auto
So I noticed the past few days my 09 F250 was clunking in the front end when turning hard even with the hubs in auto so I knew there was an issue in there somewhere. This morning I took the jack and found the passenger side would not release no matter which way the lock was turned. Pulled the locking assembly out and found a couple of the pieces of plastic cage broken (truck has 250k miles) which is to be expected I guess but the locking ring that holds the inner piece that slides over the axle stub was off and hanging next to the c-clip on the axle.
So with the plastic of the cage already being broke and the mileage on the truck it's clear I need a new lock for that side.
Here's my dilemma, I have to deliver a conference room table 200 miles away tomorrow morning that they need for meeting tomorrow afternoon at 3:00pm. I cut the rest of the plastic pieces and took the gears out leaving just the cover with the diaphragm and put it back on the hub. I can't come up with any logical reason why I can't drive the truck this way but just want to bounce it off the experts here before I take off on a 400 mile trip in the morning. The only thing I can come up with is if I were to engage the 4wd the vacuum might suck the auto-lock diaphragm in and pop it but otherwise I can't find any reason to not run it this way, the hub is still sealed up and free-wheeling just like if it were in 2wd anyway.
Ford Super Duty (1999-2016) :: How Does ESOF Locking Hubs Work In Auto Mode
I took apart, cleaned and lubed my hubs. My question is: how does the vacuum make the gears work?
Does the vacuum force (suck) the nylon assembly to push the outer gear towards the center of the truck, sliding on the inner gear thus engaging the teeth so that the axle shaft turns the hub?
When the vacuum is gone, does spring pressure pushes the outer gear away from the center of the truck thus disengaging the teeth from the inner gear and allowing the hub to free wheel?
Is this vacuum source constant during 4wd and not present during 2wd or do I not understand how the system works? I have read about a “vacuum pulse” that locks the hubs and another pulse that unlocks the hubs and this confuses me.
BTW, I like the way the Auto lock works. I had a set of Warn Auto Lock hubs on my 78 CJ. They worked on the principle of a set of roller bearings that would lock (pinch) when there was torque coming from the drive shaft. There was no vacuum involved at all. The down side was that when you coasted, the front hubs would be in two wheel drive and so you would not get the engine braking on all 4 wheels. These ESOF seem to have solved this problem.
Oh, I should probably tell you that I just purchased my 04 F250 SuperDuty 4x4 with the 6.0 diesel, just had it a week. It has been 18 years since I owned a 4x4. Before this I owned an 87 F250 2wd with the 6.9 diesel.
Ford Super Duty (1999-2016) :: F350 Won't Go Into 4 Wheel Drive - Auto Locking Hubs
My F350 4x4 won't go into 4 wheel drive unless I get out and take them out of auto and put them in locked position and when I have it in lock mode it seams to work like it's in auto mode, when I put the switch on the dash in 2wd, it seams like it's only driving the back wheels....
View 14 RepliesFord Super Duty (1999-2016) :: 2001 F250 4x4 - Auto Lock Hubs Are Not Working
2001 F-250 7.3. The auto lock hubs are not working on the truck lock hubs in and all works fine. First thought is the vacuum system has a leak or something of the sort. Had truck at the shop they are telling me the GEM module controls the vacuum to engage the auto hubs and the signal is not coming from the GEM and it need to be replaced. It was the GEM causing the problem.
View 6 RepliesFord Super Duty (1999-2016) :: 2008 F350 - Auto Hubs Won't Stay Locked
2008 F350 hubs wont stay locked in when in auto position. everything stays locked while in manual and 4x4 works fine, but in auto the hubs wont stay locked while spinning. I was trying to find the problem when i noticed that one hub stays locked all the time and the other locks and unlocks as it should but it wont stay locked while spinning. My question is do I have two bad hubs or is their a leak that wont let the hub stay locked? Also on the hub that wont unlock is this a leak problem as well or a internal problem?
View 5 RepliesFord Super Duty (1999-2016) :: 2000 F250 - ESOF Auto Hubs Not Engaging Automatically
I have a 2000 f250 CCSB 4x4 with the ESOF auto hubs. The auto hubs won't engage automatically. They work fine manually. The transfer case is engaging and correct lights are coming on. There is a little bit of vacuum coming from the vacuum switch but it doesn't seem like much to me. All the dash HVAC controls work fine though. I Lubed and cleaned inside the hubs according to Guzzles directions.
While torn down, I blew through the vacuum port on the outside of the hub and there was little to no restriction. I don't think there is enough vacuum to pull the hubs, but is that possible if all the dash controls work fine? What pressure should it take to engage them? My next step is to pick up a vacuum pump and see if I can engage them with it.
Ford Super Duty (1999-2016) :: 2010 F350 Shudders When Turning Right - Auto Locking Hubs
My 2010 F350 shudders when turning right. From what I read it could be the auto locking hubs not dis-engaging or sticking in the locked position. Tutorials show it's pretty easy to pull the auto locking Hub out taking out the three screws holding it in place. My questions is what type of grease do I need to apply to the auto locking hub once I have them out and determine that is what the issue is?
View 13 RepliesFord Super Duty (1999-2016) :: 2013 F250 - Vacuum Lines For Auto Locking Hubs Frozen
I have a 2013 F250 which has both the Manual and auto locking hub feature. I tried to plow my driveway this morning and after making one pass I put the truck in reverse and could not back up my steep driveway. The truck is showing locked in 4x4 on the dash, the 4x4 control is in high lock but the front wheels will not turn. It has been very cold here lately (-30) and I'm wondering if the vacuum lines for the auto locking hubs have frozen. I have switched the control out of 4x4 and back in several times, and it does lock in again, but as soon as I put the truck into reverse, they unlock again. The hubs are covered with ice and snow right now so I have not yet tried to manually lock them.
View 14 RepliesFord Super Duty (1999-2016) :: 2003 - Locking Hubs When Trying To Engage To Shift Into 4 Wheel Drive
I recently purchased a 2003 F350 FX4 Dually with the 7.3L Diesel. It has locking hubs and electric shift in the cab.
I have had locking hubs before that you had to engage to shift into 4 wheel drive and I have had trucks without locking hubs.
My truck didn't come with a manual, so I am looking for instructions for the proper use of this system.
Ford Super Duty (1999-2016) :: 2004 - 4x4 Auto (shift On Fly) Not Engaging?
2004 Ford F250 CC 4x4 6.0L
Took the family down to the beach today. Had some tough sand to get across in a few areas to move away from the crowds. Got a little dicey and the truck got stuck in 2WD. Switched to 4WD but back tires kept spinning. Couldn't figure out why and the truck started to dig deeper in the sand. Got a little nervous and I didn't want to start the day off with having to get pulled out.
Got out of the truck, locked the hubs in manually and I was out, no problem. Left the hubs locked until we left the beach and back on pavement.
What might be the problem and why the "shift on the fly" switch on the dash didn't seem to engage the 4WD? I even tried to switch into 4L and back to 4H (truck in neutral, break pedal compressed) and still no workie. Only manually locking the hubs would engage the 4WD.
Ford Super Duty (1999-2016) :: 2006 F250 Auto - Trans Won't Shift Into Overdrive?
I have a 2006 F250 with the 6.0 PowerStroke and automatic transmission. I just purchased this truck at an auction about a month ago.
Today I notice the transmission is not shifting into overdrive. No warning lights. If I press the tow/haul button in no change but the tow/haul light does come on. If I press it again (to turn it off) the tow/haul light goes out but still the transmission will not shift into overdrive.
This leaves me at about 2000 RPM at 68 MPH. I just had a Ford dealer perform Transmission service last week. (20,000 miles after the last recorded service.)
I am already not happy with the service I received at the dealer so I am really hesitant to take it back to them if it is something not related to the transmission service they performed.
Ford Super Duty (1999-2016) :: 2004 F250 - High Screeching Noise When AC Turned On
I have an 04 F250 6.0L and for the last month or so when I turn on my AC it makes a high screetching noise but only last for a little bit. Had a friend that works on cars on the side take a look at it one day and he said it was the AC cutch trying to engage. Does this sound like what it could be? Also if it is can it be changed out without having to remove the compressor? What all is involved in changing it out?
View 5 RepliesFord Excursion :: 4x4 Selector Switch On Dash Lights Up Properly But Auto Hubs Don't Actually Engage
My Excursion is having an issue with the 4x4 system. The. 4x4 selector switch on dash lights up properly for 4x4, but the auto hubs don't actually engage. The hubs will lock only if I manually lock the hubs. I can hear relay click, so I don't think its electrical. The hubs had new o rings installed when I did front ball joints a few thousand miles ago, and the 4x4 worked fine up until today.
View 5 RepliesFord Super Duty (1999-2016) :: 2001 - Suddenly High Idle / No Blower And Hard Shift
My '01 recently seized up and a buddy determined it was the AC pump. Replaced the belt with the bypass version. A month later, I moved across the state to Iowa. A couple weeks into living here I turned the truck on and it was idling really high (about 2500-3000) but would settle down to around 1100 when put in gear. However, shifting into gear is causing a progressively worse "jump" into gear. Hadn't really had the money or the time to take it in so I let it mostly sit unless I absolutely needed the truck.
Today, the idle is still high and does seem to cycle a bit in that it will rev up close to 3000 then settle back down around 2200 or so and then rev back up again and so on. I backed it down the drive into the sun for a little warmth and it darn near jumped a foot when I shifted. I turned the heater on defrost so I could clear the windshield and absolutely nothing came out.
I can't get into a garage for a few days to get it hooked up for diagnostics. So I thought I'd try here. My research leads me to think part of my problem may be a vacuum leak and/or maybe a sensor somewhere.
Ford Super Duty (1999-2016) :: Pin Fell Out Of Automatic Trans Gear Selector
The other day I had a metal pin fall out from under my dash and hit me on the foot (only reason I would have know if fell out till I clean the truck)
Ever since then the gear selector handle for my transmission has become sloppy and when I go to turn off the truck, I have to hold the arm up to turn key off all the way. I have looked to try and find where it goes and cannot find the location. I have also looked at a blown up parts diagram and cannot find it. Where it goes?
2002 F250 SD V10 with auto...
Ford Super Duty (1999-2016) :: Broken Metal Cylinder In The Gearshift Selector?
My automatic shift selector was extremely loose. Wasn't the two bolts up behind the dash. Turns out that there is a metal cylinder with a cutaway that seems to have fallen out of the selector housing. One of the edges of this cylinder broke off as you can see in this pic:
What is this piece called and can I get a replacement at autozone/pepboys/ect?
Ford Super Duty (1999-2016) :: 22K With Hubs In Locked Position
Its a 2016 F-250, 6.2L gas truck with the electronic shift on the fly transfer case.
I have put right at 22,000 miles on it like this, frequently at 70-80 mph.
What are the odds I have damaged it and is there anything I should do now that I discovered it - other than put them both in "AUTO".
Truck has been to the dealer twice and not once was this noticed. They blamed the squealing on the brakes which I knew it wasn't.