Ford Super Duty (1999-2016) :: 2005 - Driving Light Install In Front Bumper
I would like to install some driving lights behind the front bumper of my 2005 Super Duty, I was going to drill two 5" holes and than weld in some 5" pipe from the behind the bumper and attach some 5" KC driving lights to it. Would a hole saw work for this or is a bumper to thick? I was looking at DeWalt or Lenox hole saws their bi-metal. I know that I have to drill slow and I was going to use cutting fluid. I could use my drill press but I think I would have to figure how to clamp a bumper to the table. Then I am going to grind/sand the chrome off and paint it black. I will be taking the bumper off doing all of this.
View 4 RepliesFord Super Duty (1999-2016) :: Mounting Side Mount Tool Box Without Drilling?
Mounting a side mount tool box without drilling into the bed floor for the support legs? There are "J" hooks for the rails but there are legs that are supposed to be drilled into the floor.
View 2 RepliesFord Super Duty (1999-2016) :: Plow Mount Brush Guard Install
So I've had this WAAG brush guard laying around for a few years and figured it was time to do something with it. Of course it was bought with no mounting brackets. I had found a lower gear from a Fisher MM1 plow. Tossed the in the truck and started from there.
Broke out the cherry picker and started lining stuff up. Drilled some holes and bolted it up. It's all bolted up but I still need to take a piece of 2x3 angle and weld it to the lower plow mounts to tie the bottoms together and create a step.
Ford Super Duty (1999-2016) :: 2008 - Front Body Mount Removal?
i have a 2008 f250 4x4 i need to replace the drive side front lower body bushing and i can not get the pressed on bushing to come out what is the easiest way to get this to come apart i tried using a 4 ft pry bar and i could not get it to pop free.
View 11 RepliesFord Super Duty (1999-2016) :: 2014 - Front Body Mount Bushing Replacement
The driver side front body mount bushing on my 2014 is gone which has the grill sitting on the bumper. I started to replace it, but the bolt is sized to the nut. ran off about 1/2 inch and that is it, it will not tighten or loosen anymore.
I cut the head off the bolt, but can not get the body high enough to remove the old bushing so i can cut the nut off flush with the rad support. Now I am trying to get the air filter box out so i can cut the top of the "nut cage" off to remove the bolt and nut out the top. but i can not figure out how it is held in.
I have the intake disconnected and the filter hat off, overflow tank hose disconnected, and two bolts holding the whole thing to the fender out, but it will still not budge. What am I missing here?
Ford Super Duty (1999-2016) :: F250 - Front Bumper Bent?
I bent my front bumper. Every time I look on amazon or ebay , when I put in my year, model, engine, it says their bumper won't fit. Mine has the 3 rectangular openings, 2 have the holes for mounting and tow hooks. It is chrome with the gray plastic or rubber bottom.Xlt. Also what part is the valance?
View 7 RepliesFord Super Duty (1999-2016) :: Metal Particles In Engine While Drilling Boost Gauge
I may have got a few shavings in the engine while drilling and tapping a hole for my boost gauge on the Y pipe. I am sure I got 95% of the shavings out but am now worried about the 5% that may have fell inside.
View 8 RepliesFord Super Duty (1999-2016) :: 2014 F250 - Front Bumper Sagging
I got a 2014 F250 SD w/ 6.7 diesel. Since if owned the truck the front bumper has slowly started to sag at both driver and passenger side. Dealer says there is no adjustments for it.
View 14 RepliesFord Super Duty (1999-2016) :: 2014 Front Bumper Fit On 2001 F350?
Do a 2014 f350 front bumper will fit on a 2001 f350? Wanting to know if the bolt holes and body lines will match up? I put a 2014 rear bumper on and it bolted right up.
View 8 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Front Bumper Removal?
i've done some searching but haven't found any how-to's or instructions on how to remove the front bumper on my 06 f250. Any link on how to do it?
View 2 RepliesFord Super Duty (1999-2016) :: LED Strobe Light Mount To The Roof
I need to mount a LED strobelight to the roof of a F250 2016. not really liking to drill a hole in the roof of a new truck I thought of running it thru the existing wiring from the brake light above the rear window. Looking for info if there's a hot wire in there that I could get power from & than could just run 1 wire to a switch. How to run the wiring ????
View 4 RepliesFord Super Duty (1999-2016) :: 2000 F350 - How To Correctly Install Front Drive Shaft
I want to install a new front drive shaft in my 2000 F350. I have the new one, and it has a big nut and it is threaded for length adjustment. My old one has a rubber boot which is missing from the new one. I plan on using red locktite but I do not know the torque specs on the front universal caps. Should I take it to my mechanic? I've never owned a 4x4 before.
View 3 RepliesFord Super Duty (1999-2016) :: 2010 F250 XL - OEM Fog Light Install / Switch Didn't Light Up
I have a 2010 f250 XL v10 6 speed 4wd. I was looking into adding factory fog lights to it. I have the factory plug by the headlight. I've read that some XL trucks just need the fog lights, wiring harness for the lights and the headlight switch with the fog light option.
So today my buddy (has an 09 f250 xlt with factory fog lights) and I decided to try his headlight switch in my truck to see if it would send power to the plug by the headlight. Plugged it in, turned the fog lights on and had no power. Actually the little fog light light on the switch didn't light up that I noticed either. So we compared wiring harnesses going to the headlight switch. Both trucks have 9 wires. #21 fuse in the kick panel is intact and good.
What else my truck would need in order to use the factory fog light parts? I know I could run new wiring and use an aftermarket switch but I'd rather it be factory.
Ford Super Duty (1999-2016) :: 2013 F250 - Amber Flashing Light Install
I'm installing a new amber light on my 2013 F250 signal cab and was wondering where most people run the wires into the cab. It has a magnetic mount and I didn't want to put a hole in the roof. I have a cap on the truck and I also don't have a sliding rear window. This will not be a temp. install. Putting the wires in through a hole in the 3rd brake light?
View 3 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Fog Light Switch / Driving Lights Install
I just ordered a set of Hella 4000x driving lights for my 2006 F-250. I have an aftermarket bumper on it, so the fog lights were taken out as there was no place to put them once the new bumper was installed. The question is, will I have any issues hooking the new driving lights up directly to the fog light system so I can just run them off the fog light switch instead of having to install the new switch on my dashboard? I know the new lights are 12V, but I couldn't find info as to whether the fog lights were running 12V as well.
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Second 110V Plug Coming Out Of The Grill
Just picked up a 2002 F-250 Super Duty. I have a second 110V plug coming out of the grill. The first, on the drivers side, I know is for the block heater through the oil filter housing. The second is attached to a device that is inline of the lower coolant hose. Is this a warming device also?
View 2 RepliesFord Excursion :: Front Bumper Grill Insert?
Is there a source for a insert for the tow hooks & between the fog lights?
View 2 RepliesFord Super Duty (1999-2016) :: How To Mount Flag Pole To Bed Of Truck
I was trying to figure out how to mount a flag pole to the bed of my truck. I used to use a 5gal bucket with a pvc pipe in it and poured concrete in the bucket and put it in my bed. I have seen others use their stake pockets but don't know how they kept it from falling out.
View 12 RepliesFord Super Duty (1999-2016) :: Firestone Airbags Kit 2535 Mount?
I have a sensor module mounted on the frame right where I need to put the upper bracket for the air bag on the passenger side rear . called e-trailer and they had no clue . special kit for 2011-2013 4x4 diesel 2535. What to do????
View 7 Replies