Ford Super Duty (1999-2016) :: 2003 5.4 F250 Head Gasket / Misfire Code On Cylinder 4?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code For Cylinder 3 Misfire
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
Ford Super Duty (1999-2016) :: 2002 - Misfire Intermittently - Cylinder 3 Or 4?
I have a 2002 F250 5.4 L with an intermittent Misfire. A little history on the truck in 2011 I replaced the motor with a Ford long block motor, only the block, I used my electronics, intake, etc, this was brand new from Ford. The truck has a total of over 300K miles. Recently it has developed an intermittent misfire. I have changed all the coils and plugs and the misfire is still present. The codes are showing a misfire in cylinder 3 but could be 4 too. The misfire is intermittent because this morning I changed the plugs and truck ran fine, drove to store and it started missing, turned truck off and started up and ran fine again. It has been doing this off and on for a few weeks.
View 10 RepliesFord Super Duty (1999-2016) :: 2001 F350 - Misfire On Cylinder 3 And 4
I have a 2001 F 350 with a V10 it keeps coming back as a misfire on cylinder 3 and 4.. I replaced all of the coils and plugs and pigtails I have even swapped out the coil packs from side to side and I still keep coming back with the same code. The truck has a bad check around 1500 RPM with a load on the motor mainly doesn't in overdrive and first starting off...
View 14 RepliesFord Super Duty (1999-2016) :: 2004 V10 - Misfire On Cylinder 2 - No Compression
I bought this 2004 V10 Ford truck new.. It was at that time top of the line Ranch King with all the bells and whistles.. I have been trying for some time to figure out the miss I have. I was told yesterday that.. Misfire 2nd cylinder passenger side no compression.. They said I need to have a new Engine installed.. They would look for a rebuilt and would cost with installation around 5 grand.. I then took it to another garage and was told that's not it, but will check it out later in the week.. What I should look for.. No one seems to b able to figure it out.. I cannot afford a new truck at this time and 5 grand for this one to fix is not a reality..
View 8 RepliesFord Super Duty (1999-2016) :: Misfire On Cylinder 2 / Choppy Sound In The Exhaust
I have a 99 ford super duty with a 5.4 triton that is having a troublesome misfire. When you first fire it up it has a bit of a stutter then runs relatively smooth but the engine does still have a small shake to it and you can hear a bit of a choppy sound in the exhaust. Not completely smooth. When you drive it light footed it seems to run perfectly smooth and nice. But if you go past half throttle (sometimes you can go past that point) it starts to cough and is very slow at picking up.
When you reach between 3,250 and 4,500rpm the coughing stops. But the pick up is a little surgy, not steady. It was doing this for a while before the engine light came on. I got it scanned and it showed a miss fire on cylinder two so I have replaced the spark plug, coil, and injector but still the same issue. I opened up the catalytic converter to see if it was plugged up. Nothing there.
Ford Super Duty (1999-2016) :: 2008 F350 - Multiple Codes / Cylinder 5 Misfire
My dads truck started misfiring last week, first thing i did was scan the codes and got p0303, p0304, p0305, p0306, and p0308. Its an 08 F-350 5.4...already changed out the spark plugs and the same codes came back. I decided to do some further testing and so far all coils had spark as well as 12.4 volts going to each. I did check the switching signal and that was present as well.
Moved on to the injectors and i checked each connector with my noid lights and it flashed on all cylinders. Did a resistance check on each injector and they all registered 12.4 ohms. We did switch some coils around and all the same cylinders misfire. My next step is to do a compression test.
My biggest question is if there are any common problems with these engines besides the coils, by the way this truck has the brown coil boots and the spark plugs that dont break in the engine.
Ford Super Duty (1999-2016) :: 2008 F250 - Random Misfire Detected On Cylinder 7
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
Ford Super Duty (1999-2016) :: Misfire At Low RPMs - Code P0316
2004 SD ext cab 5.4L Gas ! I have a mis-fire at low RPMs ! Autozone said it kicked out code P0316 Crank Position Sensor ( CPS ) but the CEL was not on ! So I replaced it and Still has the same problem. I checked the coil packs there good according to the autozone diagram "how to" ! I also pulled each wire 2 check the old shade tree way to see if I could tell that way. Now the CEL is on...
View 14 RepliesFord Super Duty (1999-2016) :: 2008 - Code P0201 For Injector Cylinder 1
This is my first Ford. 2008 6.4L 165K miles full delete. Bought this truck at auction already deleted. Found an H&S pod mount instructions in glove box and so I am thinking it had their software loaded to it. I knew it had sat a while, but did fire up no problems. I have already replaced all fuel filters (actually learned I did them backwards, and did not cycle the key) and had no issues re-starting! I've put at minimum 30 minutes but no more than 1 hour run time on this thing post filter change. I'll get to the gritty. . This all started when I pulled a P0201 code for Injector Cylinder 1.
I pulled the valve cover to troubleshoot the injector, following a post I saw few days back. All checked out fine with the #1 compared with #3, and so I cracked loose the fuel line going to the #1 injector. The line was dry and thought it was strange, but I had changed out the FRP sensor prior and remember no fuel came out then either. Before pulling into the garage the truck was running rough but thought this was due to a P0193 code FRP pressure Circuit High (again). So I put the line back on, tightened the darn out of it.
I know these things see a 26K psi at times. I depressed the Schrader valve at the fuel cooler and got only a minute bit of air out. I didn't think this was enough, and so I took the Schrader valve out, hard lesson learned. I re-installed it and I fashioned a homemade tool connected the Schrader valve with a ball valve to cycle the key-on and purge out the air. I have ran the batteries down cranking trying to get it to fire. I am now getting no more air bubbles.
Had to get another diesel pickup to keep juice on the batteries. After 3 hours, 6 hours total, cannot get this thing to fire off! Am I missing something simple? Everything I have done to this point before reading the forum I have done backwards and all has been fine! Could it be that just now I am seeing the effect of the filter change being done backwards? On my scanner I can see the live FRP, it has to be the cmd, it is sitting at 29Kpsi. At this point should I re-pull the filters and start fresh?
Ford Super Duty (1999-2016) :: 2005 F350 - Misfire Code P0307
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Hard Start - Misfire Code?
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
Ford Super Duty (1999-2016) :: 2002 V10 - Random Misfire / Pending Code P0720 OSS
I have a 2002 F250 SD V10 4x4, that just started to randomly misfire [does not matter if the vehicle is in motion or in park]. I scanned the OBDII and found pending code P0720 (Output Speed Sensor). The CEL, O/D light, nor the ABS light illuminate. The speedometer functions normally.
This occurred Saturday after we got 12-18" of snow. I cleaned out the driveway, took a short drive (~ miles) & parked the truck (no symptoms). Later we went to 2 stores and then on the way home, the misfire started. The next day the misfire continues.
I have been searching & come up with the same posts that say the issue is not the OSS. It's usually a bad COP or bad wiring @ the OSS. The symptoms are not the same as when I had a COP go bad (only misfired under load between 1500 & 2500 rpm).
Personal issues: My truck does not fit in my garage, it's dark (and usually below 30 F) before I can get to look at it in the evening. Also, we are supposed to get another foot of snow tomorrow night.
Ford Super Duty (1999-2016) :: P0300 Code And Various Misfire Codes For Random Cylinders
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
Ford Super Duty (1999-2016) :: 2005 F250 - CEL Code P1299 For Cylinder Head Temperature Sensor
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
Ford Super Duty (1999-2016) :: 2003 F250 - Misfire And OD Light Flashing
OK, quick question. I have an '03 250 with the 5.4 and the OD light began flashing tonight. I looked in the forums here and everyone say's new tranny or sensor but over on the diesel forums the are saying that the alternator is a big cause of this (dirty power).
At the beginning of this year I noticed what I assumed to be a misfire when putting the motor under a load. Once up to speed it would smooth out and all was good. I was told that a plug job on these trucks is hellish and expensive since a lot of guys break the plugs off in the block. I put it off and the issue went away when the weather warmed up.
Now it's getting cold again and the misfire is back. Driving home tonight the truck died at a light. I restarted it and as I accelerated I noticed a difference in the shift from first to second and then saw the OD light blinking.
Again, the diesel guys are all talking alternator so my question is this: could the alternator cause both the OD light to flash AND the misfire? If the "dirty power" can cause the tranny to fall in to safe mode, can it also cause the ignition to be problematic?
Ford Super Duty (1999-2016) :: 2003 F250 4x4 - Misfires On Cylinder 1 / 3 / 6 And 7 - Knock P0325
2003 F-250 SD 4x4 w/5.4L engine and 4R100 trans (pic in sig) . Truck has 280K on it with about 40K on a partial rebuild on the top end.
Took the truck out offroading and got about 4" from the top of the 33" tire in water (not mud.. water) . Someone with 6' tractor tore through the puddle.....
Well the truck survived through it ... albeit dirty as all hell and developed some issues soon thereafter. Codes for misfires on cyl 1,3,6,7, general ignition coil, etc etc etc
Power washed the underbody , washed the mud off the engine bay (yeah... with water but given it was caked with mud and water to fill the plug wells... no additional harm) .
Replaced all 8 COP and 4 plugs ( easier ones to reach), oil change, oil filter, new paper cone filter. checked most all the harness connections and cleaned with alcohol also. Reset the PCM/ECU and drove the truck for about 100miles and finally just after putting a full tank of gas (92 Octane) I throw a P0325...
The engine runs very clean, no hesitation, smooth idle, smooth acceleration on both light and hard acceleration. Just the damn code. Is it the gas I just topped off? After 100+ miles with new COP and plugs it threw nothing until this and runs great. Dont hear any knock/ping/detonation by ear and feels silky smooth at idle.
I really dont want to have to tear the intake off to replace bank 1 knock...
Ford 7.3L Power Stroke (1999-2003) :: P0308 Fault Code / Misfire Detected On Cylinder 8
New to diesel trucks and wondered if this recurring code is a serious problem. I clear DTC and truck will run fine. Might stay off for 2 days or 2 months and same code comes back. Truck seems to run just fine even with service light on.
View 5 RepliesFord Super Duty (1999-2016) :: 2003 - Error Code From Obd Port?
So I just bought a 2003 f250 v10 and I've plugged in my code reader and it couldn't get any info, so I took it to auto zone and they got an error code. I took a test lite to each little connection on the port with the ignition on and only got power to some of the metal connections on the port. So I'm wondering if all the little connections should have power? If so where should I start to look to find the problem?
View 5 Replies