Ford Super Duty (1999-2016) :: 2003 F250 - Blowing White Smoke Even Replaced EGR Valve?
I have a 2003 F250 that has recently started blowing white smoke. I replaced the EGR Valve but no luck.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 F250 V10 - Bank 2 Sensor 2 Oxygen Sensor Is Faulty
My Bank 2 Sensor 2 oxygen sensor is faulty and I need to replace it. The guys at the parts store were pretty certain it is downstream driver's side, but I just want to make sure before I PB Blasted and removed it. 2008 F250 SD v10 ....
View 1 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Cam Shaft Sensor Replaced - Check Engine Light On?
You know the "mechanic's fiances truck" problem. I recently replaced the cam sensor in my 05' F250 Gas. The check engine light had been on for a while before that and my truck rode great, however I now want to sell it and I can't do that with a check engine light on. It's got about 85k miles on it.
After replacing the sensor, the light went off for about 20 miles, but it is now back on and my truck seems to miss every once in a while on acceleration or cruising. Some days it's worse than others. The check engine light still says cam sensor, but the sensor is brand new.
My fiance is a mechanic, so I don't know all the details about code numbers and such. However, I want to sell this truck pretty soon, and I would like it to run correctly. His dad (another mechanic) seems to think it could be a coil and wants to wait for that light to come on, but I would rather fix the problem and sell the truck!
Ford Super Duty (1999-2016) :: 2008 F250 Won't Start - Replaced Battery And Starter?
I have a 2008 f 250 super duty gas v10 i have never had problems with it start always starts right up and strong. After coming out of the story today I tried the remote start and it tried to turn for a couple seconds and stopped. I replaced the battery and starter and still nothing. i hear the relay when trying to start with both keys or remote start but nothing from the starter all lights are working .
View 1 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code P0721 - OSS Sensor Circuit Performance Fault
I recently picked up a 2005 f250 SD 5.4 4x4... I was having issues with sporadic shifting and wandering shifts while cruising around 100kph, scanned it and came up with p0721 OSS sensor circuit performance fault.
I checked the harness and all looks fine, now I attempted to remove the OSS at the rear of the tranny, got the 8mm bolt out however could not, for the life of me get the sensor out. I tried not to use pliers to twist the sensor or anything for fear of breaking the sensor off and having bits go into the transmission.
Ford Super Duty (1999-2016) :: 2005 F250 - CEL Code P1299 For Cylinder Head Temperature Sensor
(The truck is a 05 f250 with a 5.4l). The problem first started out with the engine temperature gauge spiking and then resetting itself when the truck is turned off and then turned back on. If I drove the truck for any distance it would go into limp mode and the CEL would come on. The code was p1299, which is the cylinder head temperature sensor, and I replaced the sensor but no luck. Then the shop and I went through all accessories hooked up and couldn't find a short until I remembered that my prodigy break controller would occasionally read "ol" or "sh" which both readings are from shorts. I tow a enclosed trailer about 85% of the time and the past week I have been towing it with a different 250 and the same break controller without a problem so I have eliminated the trailer. But the shop just said the problem was the controller and unhooked it.
Now the next day it threw the same code with the controller unhooked and the trailer hooked up. after thinking it seemed that it was happening when i accelerated so I took apart the 7 pin and sure enough there was a little water in it, but after driving it around for a little and no code being thrown I hooked my break controller up and it still was showing ol or sh so i believe there is still a short. Also I noticed that my voltage is reading right at 13v instead of the 13.8-14v it was reading before this issue arose. I think I have narrowed it down to the 7 pin harness and/or electrical in the break components, but do not know what would loop back to the temperature sensor.
Ford Super Duty (1999-2016) :: 2008 F350 - Keep Getting A Lean Bank Code - O2 Sensor?
I keep getting a lean bank code. I have cleaned tb and replaced one of the rubber lines. It only comes on when I take a good ride with the truck. Not sure what else it could be. I'm thinking O2 sensor maybe.
2008 F-350 5.4 3V. 65k miles
Ford Super Duty (1999-2016) :: 2008 F250 - No Cruise Control - Radio / Reverse Sensor And Towing System Error
I recently bought a 2008 F250 with the 6.4 diesel indirectly from a dealership. The truck itself has 220,000ish kilometers, but the engine (as well as the turbos) are Ford reman that had about 12,000km when I bought it and I have only put about 6500km on it. It is already leaking oil but that is for another thread.
The reverse sensors, steering wheel controls and part of the stock 6cd radio have never worked. The towing system has errors as well. The fuel level sensor often has problems reading the new level after I put in fuel, but that is always fixed by disconnecting the batteries and forcing a hard reset.
I figured the steering wheel/cruise control problem was due to either a broken clock spring and/or the brake pressure switch. I replaced both those as well as the airbag because the horn relay failed closed when I put it back in the wheel. It did not fix the problem. The steering wheel buttons still intermittently illuminate, but the radio controls and cruise control buttons do not function regardless. The truck isn't giving any codes either.
The towing system will activate lights and brakes on a trailer as well as set the gain, but it will not detect that it is actually hooked to a trailer. I cleaned the pins, but I haven't looked any further into it. No codes for this as well.
The reverse sensors/system does not work. It will lock itself in "off". I am guessing this is because one or more of the sensors have failed, but I am skeptical that it would be just that given the trucks other problems.
The radio does work, but the auxiliary input/mode will not work. I ran the diagnostics on the radio and on 'Test 1' I got "SELF FAIL B1342 ECU" and "B2477 CONFIG". I tried to clear the codes, but I can't. I think this means the radio is kill.
Ford Super Duty (1999-2016) :: 2008 F250 - Throwing Code - No Power - Misfiring?
My 2008 f250 6.4l just got out of the shop a week a go new small block and new pistons, throwing #1 constrabution code,map sensor and #1 cil misfire you can hear air come out of the intake, I am guessing valve train or lifter..... other problem two days after the truck throwing the codes i went to take it to the shop and would barely drive floored struggle to go 10mph put it in park rev up normal will go in reverse normal just no power in drive, no transmission codes, had it towed to the diesel shop, mech said might be a fail safe on transmission from the engine codes? it has egr/dfp h&s mini maxx tuner, the truck has 170k on body 11k on new engine before the new block that was put in last week.
View 6 RepliesFord Super Duty (1999-2016) :: Code P2195 (Bank 1 Sensor 1 O2 Sensor Stuck Lean)
So I just replace my Cat. Converter with all new sensors in them. I just replaced my spark plugs. (I'm knocking out these check engine light problems) and I think I'm getting close to the root as to why these other parts went bad. Why my o2 sensor would be stuck on "lean" ....
View 5 RepliesFord Super Duty (1999-2016) :: 2005 F250 - PCV Valve Location
I have a 2005 f250 with a 5.4l 3v. Where the pcv valve is located is it in the valve cover or attached to the intake and what does it look like? I have pulled the hoses off both sides but I have not found it let.
View 3 RepliesFord Super Duty (1999-2016) :: 2008 - EGR Valve Sticks?
Quick question, 2008 F250, 6.4. If the EGR Valve sticks/malfunctions, can this cause the truck to go into constant/frequent regens? I am asking because I am about to replace my turbo for a seal failure. The only code thrown before turbo failure was EGR flow insufficient. I want to figure out what may have caused the seal failure so that I can get that fixed before I blow through another turbo.
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F250 Won't Turn Over After STC Fitting Replaced
2005 6.0 F250 SD Powerstroke... Truck died on the road and wouldn't start
The symptoms were... I changed the Radiator and had the cooling system flushed... couple of weeks later it stopped while driving... did some research and talked to a few people and the STC valve seemed to be the issue... So new STC, new intake gaskets, cleaned and new EGR gaskets and I just put in a new Turbo (Ford installed it)... had a stripped bolt under the EGR cooler arm and had to remove the Turbo to get to it.... 14 days later......
Changed STC fitting and gaskets in the high pressure oil pump, IPR screen, exhaust manifold gaskets and Cleaned the EGR and changed gaskets and no start. Tried starter fluid and it turned but wouldn't stay on and the batteries died. Would you all say I'm on the right path?
Ford Super Duty (1999-2016) :: 2002 F250 7.3L - Replacing Valve Cover Gasket?
I'm looking at replacing the valve cover gaskets on my 02 f-250, it's a 7.3L.
Looking at them on line there are many different brands. What have you used on your 7.3L, and which has worked the best for you?
Ford Super Duty (1999-2016) :: Code P0442 On 2003 V10 - Purge Valve Solenoid?
CEL turned on this morning heading to work. Truck drove completely normal with no signs of altered performance.
Stopped by Autozone after work and they checked it with a code reader.
Came back with P0442 - "Purge Valve Solenoid"
Part sold with or without bracket.
Is this a common part to fail? How can I be sure it has truly failed? Is it acceptable to reset CEL and see if it fails again? If so, how do I reset? Where is part located?
Ford Super Duty (1999-2016) :: 2001 F250 - Overheating - Replacing Bypass Valve On Trans?
I am having some trouble with my 4R100 overheating.
Truck is a 2001 F250 XLT 7.3L with 244k miles on it. According to previous owner, the transmission was replaced around 185/190k but there was no paperwork to prove it.
I recently had a leak from one of transmission lines coming into the bottom of the radiator (the one on the passenger side). I replaced it and topped off the little bit of fluid that leaked out. Last weekend I installed a temp sensor in the transmission and hooked it up to my pillar gauges. The first few days driving with it, the temp was at/around 180 degrees, 25-30 degree outside air, unloaded on the highway averaging 70-75mph.
Today on the way home, the temp got to 180 after 35-40min of driving then continue climbing. I pulled off the highway after 1.5hrs and the temp was almost at 210 degrees. I let it idle for 5-10min and the temp didn't change. I turned it off and let it sit for 15 min. Upon starting it back up, the temp had dropped to 180. I continued driving and the temp climbed back up to 210 within 35 minutes. (65-75mph, 24 degree outside temp, unloaded). Once off the highway I averaged 35-45mph on the back roads to my house. The temp started to drop back towards 180 degrees.
Before I start throwing money at it, and installing a 6.0 cooler etc. I am thinking there is something else wrong here. I am going to look at new lines and replacing/repairing the bypass valve on the transmission. I am driving 2hrs to work each way and thats when the temp really starts to go up. The fluid doesnt smell burnt, its still nice and red. I am going to try and flush the lines this weekend and see if something is plugged/caught. I ordered an inline filter today and will put that in with a new hose from the transmission to the radiator (old one is rusted).
Ford Super Duty (1999-2016) :: 2002 F250 5.4 - Valve Cover Leaking - Gasket Replacement?
I have a 2002 F250 5.4with Air Conditioning. The valve covers are leaking and the gaskets need to be replaced. I am attempting the valve cover gaskets. I was able to get the drivers side cover off with some difficulty. For the passenger side valve cover. There is very little " no" room to get at the bolts. I read somewhere that I may have to drop the engine on that side. I will do that if I have to.
View 5 RepliesFord Super Duty (1999-2016) :: Code P2285 - New ICP Sensor
I have been trying to find a new sensor after my truck popped a P2285 code. I can't find ICP sensor at any auto parts store. I found this but it was labeled as a fuel pressure sensor on RockAuto: More Information for Standard Motor Products ICP103... Is this the same thing?
View 2 RepliesFord Super Duty (1999-2016) :: F250 - Changed O2 Sensor Still Getting P0155?
99 5.4 F250
Well, this truck i have had many many codes before. I cleared them and all went away except for p0155. I fixed my manifold leaks and cleared the codes. It came back on and i changed the o2 sensor, twice. Still on.
Ive checked the heater and input wires to the pcm and have .6 ohms each, so they are good with what appears to be no shorts. I dont know how to check the other 2 o2 sensor wires.