Ford Super Duty (1999-2016) :: P0300 Code And Various Misfire Codes For Random Cylinders
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
Ford Super Duty (1999-2016) :: 2001 - O/D Light Flashing - Got Code P0720?
I have a 2001 F250 Super Duty with a 5.4L engine, regular cab. The truck has 149000 miles on it. I bought it about a month ago and had the transmission rebuilt, the spark plugs and coils replaced. Apparently the shady dealer I bought the truck from had power washed the engine and there was water in 3 of the spark plug wells on the drivers side. When I got the truck back from the transmission shop and backed it out of the parking lot, the OD off light started flashing and the SEL light came on. The code showed to be a P0720 to which the mechanic at the transmission shop replaced the speed sensor on the top of the tranny.
He said if it comes on again then the speed sensor on the rear differential could be the problem and that he would have to charge me to replace that sensor since it isn't covered under the warranty for the transmission.. I replaced the sensor myself on the rear differential yesterday and thought the problem was fixed. I drove the truck around for 30 minutes with no problems, until I put the truck in reverse, then the OD off light started flashing and the SEL light comes on giving the same P0720 code.
Ford Super Duty (1999-2016) :: 2003 V10 - Slight Miss With Pending P0171 Code
I just purchased a 2003 F250 Super Duty with the 6.8L V10 It has really high miles on it as it was a landscaping companies fleet truck. I'm sure that it was pretty well serviced as it has 300K miles on it and it's still running pretty decent.
I picked up the truck and I have to get the smog done soon. It idles with what I can only describe as a slight miss and it runs and drives great. seems to have plenty of power for the miles that's on it.
There is no active CEL on but I scanned the OBDII system and found a P0171 Lean bank 1 code in the pending codes list of the scanner. I guess this year engine doesn't have an EGR Valve or DPFE sensor because I've looked high and low for it and there non existent on this engine.
I've checked for vacuum leaks by spraying brake cleaner or carb cleaner all over the place and it makes no difference and all the vacuum lines and connections look okay.
When it's running It does sound like a vacuum leak right behind the top of the plastic throttle body but I can't find it, I don't know if this big *** engine just sucks that much air or what.
Like I said I need to smog this thing soon and I don't want it to fail if it's missing or has another issue. The fuel injectors look new and one coil pack looks like it's a replacement...
Ford Super Duty (1999-2016) :: Intermittent Tow / Haul Flashing Light When Going Up Or Down Hill - P0720 Code
I have a 2000 F350 7.3 4x4. It began giving intermittent tow/haul flashing light, when going up or down hill but would clear and drive next time truck was cycled off/on. No ABS lights and code reader generated P0720 for the output speed sensor, now I can get it to generate just driving slowly fwd and rev a few times. All of this has been in the last few days.
Truck will stall if I take it up a slight incline with the fault. I replaced the sensor on the top front of the 4r100 transmission and also replaced the sensor on the rear differential after giving up on looking for an output sensor on the transmission. I know the 2WD transmissions have an output sensor but is there one on the 4WD version? I have read several past threads discussing the P0720. I am hoping to confirm what sensor I need to be looking at and where it is located in this application.
Ford Super Duty (1999-2016) :: F250 - Trans Shifting Hard / OD Light Flashing / Code P0720
Just got the transmission rebuilt in my truck and other then shifting hard sometimes it has been doing great, Hooked it up to the goose neck this evening and everything was fine then went to back it up and pull it forward and after a short distance the od light was flashing and when i ran a check on it it was p0720? The transmission has less then 1000 miles on it?!?!? 1999 Ford F-250 7.3 Automatic....
View 5 RepliesFord Super Duty (1999-2016) :: Losing Power - Random Misfire With No Codes?
99 F-250 SD 6.8 had an issue with it while moving from Del to Phx, Az. Found collapsed air cleaner element. It looked like someone stepped on it. I replaced it as well as the MAF. This fixed the issue. This was 350 miles into the trip. The truck seemed to be down on power as it didn't want to pull my trailer up any type of grade except with OD off. Around 2K miles into the trip in developed a random misfire with no codes. I am at my final destination and the misfire is worse. I am not showing any codes at all or pending either. It is a bit toasty outside to be out there diagnosing issues, and I won't start changing parts randomly either. I have a NGS scan tool with the proper cards.
View 5 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Random Misfire Detected On Cylinder 7
Truck Specs:
2008 f250 super duty 5.4l
78xxx miles
4x4
Automatic
Issue:
P0300 (random misfire detected)
P0307 (cylinder 7 misfire)
Let's start from the beginning...
I was getting the notorious 5.4l ticking sound. After doing research on this issue. I found that it could be a few different issues including:
Cam Phasers
VCT solenoid(s)
Loud injectors
Valves
Exhaust leak
Loose spark plug
The list could possibly go on, but these being top concerns or issues to look into.
I took it to my mechanic and wanted him to research the ticking problem. This was my primary concern due to it was getting worse over time. I didn't want to do more damage than what was possibly already done. I told him to go ahead and change the spark plugs while you're checking into what's going on. (I know those plugs can break and I didn't want to do that.)
At any rate... the plugs got changed to motocraft brand (I know the trucks can be finicky with the parts you put back into them so I went with the motocrafts to avoid any complications.) After the plugs were changed, he told me that the ticking was caused from a blown exhaust manifold gasket (yay me... not internal parts or anything too serious. Sweet!)
I had to reschedule to get the gasket done, but knowing what it was now I wasn't too concerned about driving it. So I did. The new plugs are also in the truck at this time. I drove it the next day and right away.. I noticed a misfire. Thought maybe the plug was bad. I told my mechanic about it and he said... Sounds like a COP to me.
So I get a new COP. Okay.. easy fix. Installed it and still got a misfire. Told my mechanic and he said get another COP. So I'm thinking.. "Okay.. get a new part to fix a new part.. sounds logical.. lol" so I do what he thinks might be best. I replace the COP with another new one and it's still misfiring. The new cops are also motocraft brand as well.
Okay... next step.. he claims it may be a VCT solenoid issue. At this point I don't care.. I just want my truck fixed. So he replaces the driver side solenoid. Still misfiring..
So after doing some research on the scanner... we locate some issues that are the exact symptoms I'm having. Misfire.. at low rpm.. during cruise control.. and a sudden at idle.
This information states for this drivability issue.. to spray injector cleaner/carb cleaner into the engine and possibly clean it out. Makes sense. He did this as well as changed the fuel filter. Also did a pressure test on the injectors to make sure they were good. They were. After spraying and cleaning it out, it was taken for a test drive and it seemed okay... but not perfect. The next day.. the misfire came back.
He said that if the misfire returns, that I need to contact the dealership and see if there is a pcm update. The dealership said there probably is but can't tell me until the computer is hooked up to it. (Of course there is a charge when it's hooked up) again.. whatever.. I just want it fixed. The truck is scheduled to go in next Wednesday for that. If that doesn't fix it, my mechanic said cam phasers possibly bUT still not sure for sure..
Ford Super Duty (1999-2016) :: 2002 F250 Will Not Start In Below Freezing Temps At Random
I have an 02 250 5.4. 103,000 miles. My truck at random times will not start in below freezing temps. Turns over just fine but Acts as if a frozen fuel line. I can get it running by pouring hot water on the fuel rail or a shot of starting fluid or sometimes both. It's been going on about 3 or 4 weeks now and I have ran through 4 bottles of dry gas with about 15 gallons each time. Also have replaced fuel filter and fuel pressure regulator. I'm 99.9% positive the pump is working and there are no leaks in the lines or holes in tank that I can see. My next step is to drop the tank and clean it out but trying to avoid that.
View 14 RepliesFord Super Duty (1999-2016) :: Misfire At Low RPMs - Code P0316
2004 SD ext cab 5.4L Gas ! I have a mis-fire at low RPMs ! Autozone said it kicked out code P0316 Crank Position Sensor ( CPS ) but the CEL was not on ! So I replaced it and Still has the same problem. I checked the coil packs there good according to the autozone diagram "how to" ! I also pulled each wire 2 check the old shade tree way to see if I could tell that way. Now the CEL is on...
View 14 RepliesFord Super Duty (1999-2016) :: 2003 - Cylinder 3 Misfire With No Code?
my 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 RepliesFord Super Duty (1999-2016) :: 2003 - PCM Not Communicating With Trans - Codes P0720 / P0722?
I have a 2003 Ford f250 5.4l brought it to the shop today and they said the pcm isn't communicating with the trans. The truck hesitates and stalls out at a stop. idle is OK a little studder. OD light blinks also. I put new ho2s in, new oss from ford, new plugs and coils (motorcraft).
View 3 RepliesFord Super Duty (1999-2016) :: 2002 - Misfire Intermittently - Cylinder 3 Or 4?
I have a 2002 F250 5.4 L with an intermittent Misfire. A little history on the truck in 2011 I replaced the motor with a Ford long block motor, only the block, I used my electronics, intake, etc, this was brand new from Ford. The truck has a total of over 300K miles. Recently it has developed an intermittent misfire. I have changed all the coils and plugs and the misfire is still present. The codes are showing a misfire in cylinder 3 but could be 4 too. The misfire is intermittent because this morning I changed the plugs and truck ran fine, drove to store and it started missing, turned truck off and started up and ran fine again. It has been doing this off and on for a few weeks.
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Misfire Code P0307
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code For Cylinder 3 Misfire
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
Ford Super Duty (1999-2016) :: 2002 F250 V10 Misfire When Driving Roughly Between 30 - 40 MPH
OK, not sure where to start so here goes. I have an 02' f-250 with the v-10. I just had some minor front end body work done and when I got it back I noticed that it just didn't feel right while driving. When I start it, I notice a small misfire while I stand next to the exhaust outlet. Nothing too bad, still runs great. Shortly thereafter I started noticing a more habitual missing while driving. Roughly between 30-40 mph and around 12-1500 rpm the truck feel like the driveline is about to pickle fork the truck. If I let off the gas or step on it, the vibration goes away. And very intermittent.
It will only do it when the truck is warmed up. If I only drive about a mile, it won't do it, yet if I turn around and head back, there it is! Now the weird part. I for reasons I won't get into, I left my ignition on and drained the battery. I just replaced it and for the last 2 days nothing. Nt even a misfire. Now today here it is again. I have read all over the forums for this exact problem and cannot find my exact problem. I have replaced the plugs with Autolites and cleaned the coils as well as the boots and applied a small amount of dielectric grease to the top of the plug. The boots are cleaned and not a sign of cracking or wear.
I replaced the PCV valve and nothing. All the plugs looked exactly the same. Light chocolate in color. Not one looked different than the other. I took them out again last week to verify the plugs weren't bad and the new ones all looked the same as well. I cleaned the MAF sensor also. Just cannot figure out what could be doing this all of the sudden. I don't see where anything wasn't plugged back together when it was being worked on and why would a new battery make it go away for a short time? Oh, and lastly, I have a superchips programmer that came with the truck and there are no codes showing and my check engine light has never came on yet.
Ford Super Duty (1999-2016) :: 2005 F250 - Hard Start - Misfire Code?
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
Ford Super Duty (1999-2016) :: 2001 - Transmission Malfunction - Sluggish - Codes P0732 / P0720 / P0503?
My '01 7.3 is having some transmission problems, My O/D light is flashing. Trying to go after stopping at a light is a difficult, it drives very sluggish, like its not in overdrive. Scanned it and got three codes P0732, P0720, P0503. I replaced the ABS/VSS on the differential and the problem still exist.
View 1 RepliesFord Super Duty (1999-2016) :: 2002 F250 V10 Rough Idle / Misfire Under Load
I have a 2002 F250 CCSB Lariat 4x4 with the Triton V10, I'm up to 232,000 miles so far and fairly happy with the old girl. Just this weekend, I noticed some hesitation when at idle and even more rough running when under slight load. The misfire/hesitation is worst when going up a slight hill, when the truck is accelerating at low RPMs.
I am getting zero trouble codes or freeze frame conditions on my scanner. What should be my order of diagnosis? Vacuum test at line from PCV to TB, COP test? EGR inspection? Plug inspection? Also, how do you test a coil if resistance is not a reliable method?
Ford Super Duty (1999-2016) :: 2003 5.4 F250 Head Gasket / Misfire Code On Cylinder 4?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 Replies