Ford Super Duty (1999-2016) :: 2003 - Cylinder 3 Misfire With No Code?
my 03 f250 has a 5.4 and i cant seem to get rid of a misfire in cylinder 3. i had a p0353 code but that no longer shows up. i replaced all the coils with Accel coils, replaced the plugs with motorcraft platinum. i have checked the wire all the way back to the PCM and it checks out. i replaced the pcm with one that has been reprogrammed. i have swapped the injector and coil with another position and still get misfire at #3. Replaced the coil connector with a new one. I have good fuel pressure. I no longer get the code but the misfire is still there, unplug the coil and injector while running and no change. Unplug a different cylinder and you can tell the change. I checked compression and its good. I am lost here!!!!
View 14 RepliesFord Super Duty (1999-2016) :: 2005 F350 - Misfire Code P0307
I had a 05 f350 5.4 3v come into my shop with a CEL. Did the usual it had a p0307. So I did the usual again changed plug and coil plug cam out no prob they were done 15k ago. Test drove a few times and it was fine. Few days later customer brought back with same code p0307. thought maybe I got a bad plug or coil so I moved them to #6, misfire stays on #7. When I drive it local its fine when I go to pull on to highway and really put my foot in it CEL flashes (misfire) and it pings like crazy and loses all power. Scan it back at shop and still only p0307!!
View 10 RepliesFord Super Duty (1999-2016) :: 2005 F250 - Code For Cylinder 3 Misfire
My 5.4 F250 with 200,000 miles having many problems... It all started a few months ago, when the cam needed to be replaced, and a cam phaser was also replaced at the same time. It ran fine after, then threw a code for cylinder 3 misfire. The guy I took it to said it was due to the huge crack in the exhaust manifold and that was messing with the o2 sensor coming up as a cylinder 3 misfire. So, got the new manifold and it was good for a few weeks.
Now, starting the other night, Friday the 13th, it threw a CEL when I was coming into the driveway. It had been throwing a code every once in a while, and I brought it to school to scan it Friday the 13th but there was no code. So, I assume that it is an intermittent problem, no big deal. When I go to get in my truck to go to work a few hours later, the 5.4 cranks... and cranks... and cranks.
I get it to fire up, and it dies again. Run codes, and it says that the cam positioning sensor is broken. Replace both of them, still acts up ie. doesn't start when it does start it runs very rough and stalls. Get it up to my uncles shop, and replace fuel filter.. Still runs like trash. Run codes now, and it says rich/lean in bank 1.. My uncle tells me to move my truck out of the shop, so I start it up, and it runs great. No hiccups, it idles perfect as I move his truck out of the shop first.
I park my truck outside and let it idle for about 10 mins, and when I come back out it is still idling, perfectly fine. I get in, put it in reverse, and get about 20 feet when it dies and will no longer start back up. What could be going wrong?! Sick of throwing money into this thing! At one time while started up in my uncles shop, it was blowing black smoke, as if it was a diesel!
Ford Super Duty (1999-2016) :: 2005 F250 - Hard Start - Misfire Code?
I have a 2005 F250 with the 5.4. This truck has been one thing after another, as you can tell from my other posts. The problem this time is, if it cranks hard to start because it's cold(can be anywhere from as high as 32, but usually in the teens) it will start just fine, then several minutes later throw the check engine light. Put the scanner on, like clockwork, 4 codes, always cylinder 1 misfire pending, misfire on first 1,000 revolutions pending, cylinder 1 misfire confirmed, misfire on first 1,000 revolutions confirmed.
Sometimes you can hear a slight lope in the idle when it does this. Clear the codes, runs perfectly fine. It will never do it after it's been started for the day. Some days you would think for sure it would throw it when it's frigid and the winds been blowing on it, it doesn't bother, other days you wouldn't think it would, and it does.Can the computer think that since it didn't start right up, it misfired?
Ford Super Duty (1999-2016) :: 2002 V10 - Random Misfire / Pending Code P0720 OSS
I have a 2002 F250 SD V10 4x4, that just started to randomly misfire [does not matter if the vehicle is in motion or in park]. I scanned the OBDII and found pending code P0720 (Output Speed Sensor). The CEL, O/D light, nor the ABS light illuminate. The speedometer functions normally.
This occurred Saturday after we got 12-18" of snow. I cleaned out the driveway, took a short drive (~ miles) & parked the truck (no symptoms). Later we went to 2 stores and then on the way home, the misfire started. The next day the misfire continues.
I have been searching & come up with the same posts that say the issue is not the OSS. It's usually a bad COP or bad wiring @ the OSS. The symptoms are not the same as when I had a COP go bad (only misfired under load between 1500 & 2500 rpm).
Personal issues: My truck does not fit in my garage, it's dark (and usually below 30 F) before I can get to look at it in the evening. Also, we are supposed to get another foot of snow tomorrow night.
Ford Super Duty (1999-2016) :: P0300 Code And Various Misfire Codes For Random Cylinders
New plug on right, lower bank 2 plug on left
Started getting a P0300 and various misfire codes for random cylinders. Truck has 95,000 kilometers so figured I would change the plugs. Several of the plugs on the lower bank on both sides were pretty much toast. Most of the plugs on the top looked good. All of the plugs had a small deposit where the spark hits the ground probe. Picture is typical plug from lower side. changing the plugs should make a big difference in how she runs and eliminate the codes.
Took right on 4 hours same as dealer said it would. I would have got it quicker but it was not a race.
Ford Super Duty (1999-2016) :: 2003 5.4 F250 Head Gasket / Misfire Code On Cylinder 4?
After replacing most of the underside of my Super Duty, Complete front end, backing plates, brakes, rotors and shocks, I have a misfire code on cylinder #4. I replaced the plugs, cleaned the MAS and filter and rotated the coil to cylinder #1. Still have a misfire on #4 and noticed the coolant slightly low and some condensation on the oil cap. Could this be the intake gasket? My mechanic is away for 2 weeks and I think the price at the dealer will kill me. I have 63K on the truck, don't tow and plow mostly family members. It's getting a little rusty but is still in good shape.
View 13 RepliesFord F-150 (2004-2008) :: 2006 - Random Misfire Code P0316
Friend has a 2006 with the 4.6 motor. From time to time he gets a random misfire code ( I think its 0316).. He claims it will only do it when the gas tank is less that half full. I don't see any correlation between fuel level and the code. I am going to check fuel trim values, etc, when the code is set, this weekend.... all I can assume is low fuel pressure which sets the code... Any problem with the pressure module or fuel pump / discharge hose that is related to low level in the tank ?
View 3 RepliesFord Super Duty (1999-2016) :: 6.0 Engine Idle RPMs Are About 770
Just changed the oil in my 6.0 and I'm sitting here looking at my tuner and is telling me my idle rpms are about 770.
Before I changed my oil it idled around 750.
It's running fine, I was just wondering why it changed? More pressure to the injectors with the newer oil?
Ford Super Duty (1999-2016) :: 1999 F350 V10 - Loss Of Power / No Acceleration Over 2500 RPMs
Truck sat for 1 1/2 years. Changed filter and put in 15 gallons of fuel. Had maybe 1/2 gallon old fuel in tank. MAYBE. Fixed fuel line because it wasnt getting fuel and it fired right up and idles great.
Truck has no acceleration over 2500 (or so) RPMs but idles fine. This is depending on how hard you push the pedal of course.
If you drive the truck normally like a grandmother it seems to be ok. As long as you dont need a passing gear or need to accelerate more than 1/4 pedal
If you try to push the pedal to get the next higher gear it will sometimes hit the gear fine. IF you floor the truck it will totally lose acceleration. Then the truck will run like crap even slow for a good while. But then it will clear up for the low end. Then you can drive it normally. Then when I think I can test the upper end I get the same thing again.
Ford Super Duty (1999-2016) :: F250 V10 Misfire - Shaking At 80 KMH
I have a 1999 f250 v10 auto. It has 3 miss fires thats im stumped with .. Ive replaced all spark plugs, all coils , I've had injectors out and were cleaned and it still miss fires. I can disconnect the coil and injector on the cylinders and the motor runs the same. Ive swapped the coils and injectors around to make sure it wasn't them. What else could it be? Frustrated I've had the truck for 2 years and haven't figured them out. Ive had them go away for at most a day. Also the truck has a shake at 80 kmh not sure if its from the miss...
View 13 RepliesFord Super Duty (1999-2016) :: F250 - RPMs Surge When Let Off The Gas While Driving
I've got a 99 f250 5.4 that runs like a top. In the last 6 months I've been chasing a little problem. It doesn't happen all the time but seem to be happen more and more. While driving any speed If I let off the gas the RPM's hold at around 1500 then surges down to 1000 then back up again to 1500.
Does that 2 to 4 times then all good. Give it gas again it does it again. It kind of does it when it wants. Could be fine for a trip around then next trip it acts up again. Checked a lot of the vacuum lines, PVC valve and replaced the idle control next to the EGR valve. EGR is next.
Idles and runs fine except the surge thing..
P0401 code as well.
Ford Super Duty (1999-2016) :: 2003 - Missing At Higher RPMs?
I have a 03 F250SD with ~145,000 miles on the 5.4L. Just recently I have been having what seems to be a miss, or possibly a dead cylinder. I thought it might be a dirty MAF, but I cleaned it and have the same problem. The miss is more noticeable at the higher RPMs. I am checking the plugs today. So any solution? I refuse to take her to the shop and having another man up in her manifold.
View 8 RepliesFord Super Duty (1999-2016) :: F350 Missing At High RPMs
I have a miss at high rpms.. I pulled this engine, manual trans, and 4x4 axle and put them in my F350 Majestic motorhome. 156,000 miles on the engine. Slightly dusted engine with good compression 375-400 (cranking and corrected for altitude). Has a little bit of a long start.
No smoke on start up unless 10 degrees or colder
No smoke when pulling either.
Glowplugs ...Good
GPR... Good
Checked resistance from IDM to injectors ...Good
History of some ether for starting before I got my hands on it. I have AE with the ford enhancement. But I am new to working on a powerstroke and new to AE.
ICP ...new
CPS...new
Oil ....new
EBP...new
Installed a pressure gauge to the drivers side upper port on my fuel bowl:
60 psi at idle
55 psi at WOT 2500-3000 rpms under a load
HPOP stabilized pressure is 2750 @ 40% duty cycle
Truck still misses (semi-intermittently) at higher rpm with a load.
Rechecked codes KOEO: None present
I visually inspected valve movement while running (idle). Did the buzz test when cold.... All injectors sounded the same when tested individually.
Did a cct when not completely warm:
P0266
p0272
Repeated the test at normal operating temperature:
P0266
Torque values on rocker arms bolts and injector holds are good. Fuel quality isn't an issue since this problem has remained for 5 tanks of fuel. What I should do next?
Ford Super Duty (1999-2016) :: RPMs Jumping - OD On / Off Light Keeps Blinking
My truck is acting up. Last night when I was parallel parking I noticed the RPM was jumping, I then noticed the OverDrive switch was blinking. I turned off and turned it back on and the issue went away. This morning on my way to work, it did exactly the same and it automatically corrected itself. The overDrive ON/OFF light keeps blinking.
My truck : 7.3 Diesel, Auto trans, 86 K Miles, Super Chip.
Ford Super Duty (1999-2016) :: A/C Does Not Cool At Slow Speed And Low RPMs
2006 F250 6.0L CC Lariat with Climate Control
- 1st Start in morning, AC Blows cold.
- Run it down the Interstate AC Blows cold.
- Get back into traffic, slow speed, low RPM, AC doesn't cool.
Is this likely the clutch going South or low Freon perhaps? At higher RPMs, 1000+ seems to work good. At idle, when hot, not so much. Just looking for possibilities.
Ford Super Duty (1999-2016) :: Occasional Misfire With Low RPM - High Torque
On my '99's 5.4l with 55k, I've got a slight misfire occasionally with lower rpms and higher torque - basically going up a grade that's not quite steep enough for the truck to downshift, but clears up right away the instant it downshifts and gets some rpm. It generally seems like weak spark, or perhaps an injector spray pattern such that it doesn't always get fired off.
To give some history, the truck had more or less sat in a farm garage for ~5 years driven maybe once a quarter before I picked it up ~2 years ago. When I first picked it up, it misfired all over the place. I didn't think much of it, considered it gummy fuel, and dumped a couple cans of SeaFoam in the tank, replaced all 8 plugs (pretty sure with motocraft plugs though I don't explicitly remember), checked my air filter, etc and the misfires cleared right up and it purred nice and smooth like a happy little motor. That was at ~45k, or 10,000 miles ago.
Now it's starting to hiccup again and I'm not entirely sure why. The plugs should be nowhere near burned up yet and there are no lights on the dash. It's never come close to overheating and the only oil leak I know of is that famous small drip on the inside-rear of the passenger side bank drips on the exhaust header just enough to stink every so often when I come to a stop. I don't believe I'm burning any oil and certainly not near enough oil to foul a plug. Including that drip, I go about 3,000 miles before needing to add a quart. I've dumped 2 bottles of Berryman's in the fuel tank and it seems to work, but it's definitely not gone, so I'm thinking it's probably not oil related and more fuel/spark.
I'd had it in the back of my head to replace the fuel filter as well, but I hadn't gotten around it yet as it seems to be getting fuel at high rpm's just fine. I went ahead and bought the filter the other day and plan to install it shortly. It doesn't really make sense that that's what it would be, but I figure I'm due and it's worth a shot. If they were old plugs, I'd just replace them out, but they seem to new to be causing any issues.
Ford Super Duty (1999-2016) :: 2001 F250 - How To Diagnose Misfire With No CEL
How to diagnose misfire with no CEL? 2001 F250 5.4. What could cause it?
View 13 RepliesFord Super Duty (1999-2016) :: 6.8L V10 Rough Idle And Hard Misfire
My F53 motorhome has a rough idle and hard misfire but is not setting any codes. I've put new plugs in it and not change.
View 7 Replies