Ford Super Duty (1999-2016) :: Carrier Bearing Crapped Out
So, my 2004 F250, CCSB, Fx4, 6.0l, truck broke the carrier bearing today. There is an annoying hum that modulates, the drive shaft has a lot of play and there is light visible at the top of the bearing. The problem is that it broke on a 550 mile trip to Franklin, TN and I need to make the return trip. Is there anything catastrophic that can happen running it this way?
View 14 RepliesFord Super Duty (1999-2016) :: 2008 - Replacing Carrier Bearing?
I am looking to replace the carrier bearing and (u joints while I'm in there) on my 08 F-250. I do not have access to a lift so this will be done while on the ground. Am I asking for trouble by doing this on my back?
View 14 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Front Wheel Bearing Noise
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
Ford Super Duty (1999-2016) :: AC Compressor Bearing / Pulley Removal For Replacement
Need to replace the ac compressor bearing/pulley on my 2001 f350 7.3. My question is do I need a special tool like a pulley puller or is there another way to remove pulley? I already have the clutch assembly removed as well.
View 1 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Wheel Bearing Conversion?
I have a 2000 F-250 SUperduty with a dana 50 front end , and as most of you know the front hub bearing's are junk, and expensive to replace. I know dynatrac has a kit to convert it to the tapered, cheaper, servicable bearing's. But 2g is a lil out of my price range. I was curious if anybody has tried takin the knuckles and stub shafts off an older dana 60 and putting the knucke's on the front axle to get the older bearing style instead of the hub bearing and the actuall lock outs instead of the POS vaccum style.
View 4 RepliesFord Super Duty (1999-2016) :: F250 - Headlight Removal?
I dont want to pry on the wrong thing and brake something. I am trying to remove the headlight. I was told that their are some pins that need to be pulled up. I dont see any pins. I do see two plastic clips on each side of the headlight. They are flat on the top with a small slot in them. There is a "T" stamped on the top of it. Are these the pins? I tried to find a shop manual today without much luck. Looking for a picture to show the pins that need to be removed.
View 7 RepliesFord Super Duty (1999-2016) :: F250 - Front Axle Needle Bearing Replacement
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Rear Pinion Bearing Replacement
I am working on my Dads 01 super duty with a 5.4, automatic, and the pinion bearing has seized up due to a lack of fluid from a rusted out rear diff cover. The tag on the diff cover had a 10.5 stamped on it and has 12 bolts. Is this known as a ford 10.5"
I have changed gears and pinion bearings in a Dana 70 before is this the same process? What are part numbers for a new pinion bearing and seal? Gears are in fine shape.
Ford Super Duty (1999-2016) :: 2004 F250 4WD - Front Wheel Bearing Replacement
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesFord Super Duty (1999-2016) :: F250 - What Size Socket For Center Bearing Replacement
1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Hub Assembly Removal
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Noisy Alternator - Bearing Part Number?
I have an 2003 F250 with a nosiy alternator and need to change the bearings. I would like to have the bearings on hand before i take it apart. What is the part numbers for the bearings I need?
View 3 RepliesFord Super Duty (1999-2016) :: 2008 F250 - Little Bit Of Movement In Front Wheel Bearing And Hub Assemblies
I have a 2008 F250 5.4 4x4 supercab long box (68,000 miles) that has a little bit of movement in the front wheel bearing and hub assemblies. Made it through inspection OK but it will need to be changed soon. Just asking for everyone's thoughts on brands they prefer. I have had great luck with Moog brand products in the past. I put SKF hubs on my wife's 2010 Explorer and they I would say are top quality also. Not interested in a conversion kit or cheap junk. I want a good quality unit. What brand has everyone had good results with? Are Moog or SKF the way to go?
View 8 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Front Wheel Bearing / Manual Hub Whining
Well, I've been meaning to get to servicing/re-greasing the front hubs/bearings for a while but somehow it keeps getting moved down the list.
2000 F250SD 4X4 Gas Manual Hubs+Trans
I'm currently going through the many threads that turned up in my search query.
Driving slow with the windows down it seems like a low whine or squeal coming from the left front. Tone changes when working the steering wheel left and right. Haven't detected any grinding sounds. Any other techniques for isolating the problem? It's going up on jack stands tonight and I'm going to see if there is any wobble from the front wheels and I'll listen as I turn each of the front wheels. Oddly, the right front hub is hard to turn. Left front turns easy.
Viewed Rob259956's videos on servicing the hubs. Currently researching accessing the wheel bearings. It seems pretty straightforward. Truck has been off road but not mud bogged or anything like that. I'm guessing a bad bearing will be easy to identify as will a bad o-ring but any other stuff I should look closely at?
Ford Super Duty (1999-2016) :: 2001 F250 - Transmission Leak - Replace Bearing / Seal?
I have a 2001 F250 Super Duty 5.4 Triton motor with a Transmission Leak. I have drained the Transmission, replaced the Transmission pan gasket and filter. The auto parts store also had me purchase the Torque Converter bearings/seal along with enough transmission fluid and a bottle of Lukas Transmission fix. Do I really need to replace the bearings/seal if I have everything else already ?
View 2 RepliesFord Super Duty (1999-2016) :: 2003 F250 - Replace The Front Hub Wheel Bearing Assemblies?
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Rear Blocks Removal
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 RepliesFord Super Duty (1999-2016) :: 2004 F250 - 4x4 Shift Knob Removal?
I tried searching and googling but came to no results, unless its like similar trucks. How do the 4x4 shift remove? I have an 04 F250 and someone decided to put the shift on sideways so the 4HI and etc read upside down before I purchased the truck. Do I just rip the thing off?
View 1 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Rear Seat Removal?
I would like information how to remove the rear seat back on a 2012 F250. I want to remove the head rests and from what I can find out they are bolted solid to the rear panel. I asked the same question earlier and got a reply for 2011, would that be the same? Is there any place I could get a schematic, a picture is worth a thousand words.
View 5 Replies