Ford Super Duty (1999-2016) :: 2007 4x4 Hub / Bearing Assembly Part Number
I am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 RepliesFord Super Duty (1999-2016) :: Rear Wheel Seal And Bearing Part Number Check
Replacing the backing plates on my rear end, figure get new inner bearings and seals in there. Bearings seem fine but cheap insurance, dont wanna pull it all off again.
When i pulled my hub off, the hub seal stayed on the housing shaft, this is normal? Just gotta pry it off there somehow?
Then new seal-TIMKEN 370247A just tap it into the back of the hub? Also is this the right inner bearings? TIMKEN NP114036
Ford Super Duty (1999-2016) :: 2014 F250 - Part Number For Tailgate Spoiler Cap
I'm trying to locate the part number (and a replacement) for the plastic piece that covers the top of the tailgate (when its shut) next to the step. It's about a 12 to 16 inch long piece of plastic which has some broken tabs on it, so everytime I drop the tailgate, it either flies out or starts to... I checked the fische online and I don't even see it in the picture. I did find some one-piece parts called "tailgate spoiler cap" but I didn't find any to fit a 2014 F-250 with the step on the tailgate. Should I just tell the wife to go hot-glue it ?
View 1 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Parking Brake Lever Part Number?
Parking brake lever for the park brake on my 2001 F250 srw. Both are rusted up but im having trouble finding the part.
View 1 RepliesFord Super Duty (1999-2016) :: 2001 F250 4x4 - Loud Whining Noise Found / Wheel Seal Rubbing On Inner Part Of Bearing
I have a really loud whining kind of noise found that its the wheel seal rubbing on the inner part of the wheel bearing. I was just curious if its safe to drive with the spindle removed from the axle?
View 5 RepliesFord Super Duty (1999-2016) :: 2007 - Transmission Filter Part Number?
2007 F250, V10. What is the part number for the transmission filter?
View 3 RepliesFord Super Duty (1999-2016) :: Single Steering Stabilizer (in-line) With Brackets Part Number?
I'm wanting to get a single in-line steering stabilizer for my '05 F250 4x4, but I can't seem to find any that include brackets.
I don't need a dual setup because I'm not running a big lift or big tires, but I want an inline stabilizer so that I can just leave the stock one in place.
What is the part number for one that comes with the mounting brackets?
Ford Super Duty (1999-2016) :: 2003 F250 - Alternator Not Charging Battery?
Took in the alternator to get it checked and they said it was good. Put it back on and it seemed like it was charging according to my volt meter (14.24-13.5 v)
Today, it's not charging. Only reads 12.2 v while running. Is there a fuse or something I need to check? Grounds? It seems intermittent.
2003 F-250 V10 6.8 liter 255,000 miles.
Ford Super Duty (1999-2016) :: 2003 F250 - Replace The Front Hub Wheel Bearing Assemblies?
I am needing to replace the front hub wheel bearing assemblies on my 03 F250 4x4. I know Ford changed the studs from coarse thread to fine thread in between the 02 and 03 model years. Mine has a build date of 08/02 and I haven't been able to find the exact date they switched over. I'm ordering the parts online and want to get it right the first time.
View 3 RepliesFord Super Duty (1999-2016) :: 2014 F250 - Heater Noisy And Not Working Well
I bought the wife a truck a few weeks ago and she said the heater wasn't working well and was noisy. So I hoped in it at lunch today and she was right, barely any heat output and its noisy coming from behind the passenger airbag.
View 1 RepliesFord Super Duty (1999-2016) :: 2008 F250 Noisy At 45 To 65 Miles Per Hour
My 2008 f 250 with 75k on it is making some unreal noises at 45 to 65 miles per hour. Almost sounds like someone is tapping on the top of the cab.
2008 standard cab with utility body
2 wheel drive
75,000 miles
Ford Super Duty (1999-2016) :: 2001 F250 - Heater Blow Warm For The Most Part
Sunday I bought a 2001 f250/5.4 to replace my 91 f250. I didnt drive it yesterday, but this morning on my drive to work the heater was very weak, it seemed to blow warm for the most part, but was barely pushing air even on high. I flipped it over to A/C to see if it blew any harder and it did. Does the blower motor need replace? if so why does the AC blow harder than the heater?
View 14 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Wheel Bearing Conversion?
I have a 2000 F-250 SUperduty with a dana 50 front end , and as most of you know the front hub bearing's are junk, and expensive to replace. I know dynatrac has a kit to convert it to the tapered, cheaper, servicable bearing's. But 2g is a lil out of my price range. I was curious if anybody has tried takin the knuckles and stub shafts off an older dana 60 and putting the knucke's on the front axle to get the older bearing style instead of the hub bearing and the actuall lock outs instead of the POS vaccum style.
View 4 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Horn Goes On And Off / Radio Turns On Without Key In Ignition / Number 4 Coil Is Not Firing
I have a 2001 f250 5.4 triton. My cb antenna hole leaked water in cab, soaked my fuse block. Horn goes on and off, radio turns on without key in ignition, truck only starts when key is on and I bridge solenoid, and number 4 coil is not firing. I have let truck dry out, fixed the leak. Everything is bad to normal except starting issue and coil issue.
View 6 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Front Wheel Bearing Noise
2002 F250 4 wheel drive manual hubs, 7.3....
My first thought was to have the tires rebalanced and rotated to see if it is tire noise? I am hearing damage on top of the noise from the 7.3, hard to be sure!
Ford Super Duty (1999-2016) :: F250 - Front Axle Needle Bearing Replacement
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Carrier Bearing Removal And Vibrations
I started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
Ford Super Duty (1999-2016) :: 2001 F250 - Rear Pinion Bearing Replacement
I am working on my Dads 01 super duty with a 5.4, automatic, and the pinion bearing has seized up due to a lack of fluid from a rusted out rear diff cover. The tag on the diff cover had a 10.5 stamped on it and has 12 bolts. Is this known as a ford 10.5"
I have changed gears and pinion bearings in a Dana 70 before is this the same process? What are part numbers for a new pinion bearing and seal? Gears are in fine shape.
Ford Super Duty (1999-2016) :: 2004 F250 4WD - Front Wheel Bearing Replacement
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 Replies