Ford Super Duty (1999-2016) :: Bad AC Pulley Bearing Or Compressor
I am not sure which it is but I cannot turn the pulley by hand. How do you tell if the pulley is bad or the whole compressor? I went out to start the truck and it wouldn't start. It died so I restarted it and then I seen the smoke from the front of the truck. I opened the hood and the flipping belt was just hanging there. Is there a way to just bypass the unit for now? I wont be needing the AC till summer and that is several months away.
View 3 RepliesFord Super Duty (1999-2016) :: 2006 - A/C Clutch Seized - Replace Bearing And Pulley?
i replaced my a/c compressor on my 2006 f-250 2 yrs ago but had not refilled with r134..only the pag oil. Now i decide to refill seeing my wife uses the truck and compressor would not engage, i was able to bypass it by removing relay and jumping it with a paperclip. Compressor started up but seems to have seized on pully. the pulley seems fine and still turning freely. I can no longer turn it manually when truck is stopped and i could before i jumped it. could the clutch only be replaced or does the bearing and pulley have to be replaced
View 10 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Carrier Bearing Removal And Vibrations
I started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
Ford Super Duty (1999-2016) :: F250 - Front Axle Needle Bearing Replacement
I own a 1999 F250 super duty and have the front end apart to service the u joints , I noticed that i have bad axle stub needle bearings on one side. I was wondering what is involved in taking those out and replacing them, it looks like they are held in place with some type of spanner nut. My next question :Would it be worth the cost just to replace the whole bearing hub assembly? The truck has 134000 miles on it.
View 10 RepliesFord Super Duty (1999-2016) :: 2001 F250 - Rear Pinion Bearing Replacement
I am working on my Dads 01 super duty with a 5.4, automatic, and the pinion bearing has seized up due to a lack of fluid from a rusted out rear diff cover. The tag on the diff cover had a 10.5 stamped on it and has 12 bolts. Is this known as a ford 10.5"
I have changed gears and pinion bearings in a Dana 70 before is this the same process? What are part numbers for a new pinion bearing and seal? Gears are in fine shape.
Ford Super Duty (1999-2016) :: 2004 F250 4WD - Front Wheel Bearing Replacement
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesFord Super Duty (1999-2016) :: F250 - What Size Socket For Center Bearing Replacement
1999 F250 CCSB Lariat 5.4, 2 wheel drive. I plan to replace the Driveshaft Center Bearing in the next few days. What size is the Nut that I have to remove to remove the yoke next to it so I can press the bearing off?
View 4 RepliesFord Super Duty (1999-2016) :: Front Rotor Removal For Replacement
I can't figure out how to get my front brake rotors off to replace them. I removed the caliper and thought the rotors should just come right off but they didn't? I then pulled the hub out and there was a retaining ring with a good size nut behind it , but you shouldn't have to remove the hubs to remove the brake rotors should you?
The stats of the truck are 04 f250 4wd w/manual hubs!
Ford Super Duty (1999-2016) :: Slight Squealing Noise From Pulley When Truck Started
So a few months ago I would occasionally hear what appeared to be a slight squealing noise from a pulley when I started my truck. It was very intermittent, so I didn't think much of it.
After a few weeks, I realized I was only hearing it on colder mornings - it would also go away rather quickly. I bought a mechanic's stethoscope, and figured I'd get to it on a slow day.
Today, I finally broke out the scope and tried to figure out the source. Didn't really find any pulleys making noise, and I did notice that when I shut the truck off, it squeaks for a second or two as it comes to a complete stop.
My dream of finding a bad pulley or perhaps a power steering pump was crushed. I had hoped to do a little Easter wrenching and put this noise to rest. So, I did what any good mechanic would do - I Googled the issue.
I'm reading that it could be the belt. Certainly wouldn't bother me too much as that is an easy fix. The belt isn't too old - about 4 years and 20 - 30K on it.
I took a few pics of the belt and can take a video of start/stop ....
Ford Super Duty (1999-2016) :: Muffler Bearing Went Out
Actually the previous owner of my 7.3 Dually cut the muffler out and straight piped it, it's really not that loud but too much drone for long highway hauls.
What's a good replacement muffler for a 7.3? Wouldn't mind a little bit of sound, it already has an oversized tip.
Mercury - Sable :: 2000 - Replaced A/C Compressor Pulley Bearing, Now Car Will Start But Dies Immediately
I am completely lost now, spent alot of time trying to get the pulley off to replace the bearing, finally got that done, turned on the car, and it dies almost instantly unless i have my foot on the gas.... it runs really rough until i rev it up to at least 2K.
View 8 RepliesFord Super Duty (1999-2016) :: Carrier Bearing Crapped Out
So, my 2004 F250, CCSB, Fx4, 6.0l, truck broke the carrier bearing today. There is an annoying hum that modulates, the drive shaft has a lot of play and there is light visible at the top of the bearing. The problem is that it broke on a 550 mile trip to Franklin, TN and I need to make the return trip. Is there anything catastrophic that can happen running it this way?
View 14 RepliesFord Super Duty (1999-2016) :: Wheel Bearing / Hub Assembly Going Bad
How can you tell when your wheel bearing/hub assembly is going bad? I am hearing what sounds like "metal-on-metal" and I've already changed the brake pads, but the sound still persists. I was thinking about changing out the brake rotors since I did notice an inch long score on the rotor when I was replacing the pads. I don't want to spend a couple hundred dollars on rotors to find out it was my wheel bearing/hub assembly all along.
View 8 RepliesGolf IV / Jetta IV :: 2.0 AC Pulley Noise / Bearing Replacement?
Wondering how I would take the A/C pulley off to change the bearing or fix the chirp squeal it is making.
I have spun this pulley by hand and it is the culprit making the noise.
It has an inner pulley and an outer pulley(belt pulley). Both spin freely and are not bound up. Just want the terrible noise to go away.
Ford Super Duty (1999-2016) :: 2008 - Replacing Carrier Bearing?
I am looking to replace the carrier bearing and (u joints while I'm in there) on my 08 F-250. I do not have access to a lift so this will be done while on the ground. Am I asking for trouble by doing this on my back?
View 14 RepliesFord Super Duty (1999-2016) :: Rear Wheel Bearing Making Noise
Have a rear wheel bearing making some noise. A friend told me that it is always the outer bearing that goes first . Can you replace the bearing without replacing the race?
View 14 RepliesFord Super Duty (1999-2016) :: 2007 4x4 Hub / Bearing Assembly Part Number
I am not sure mine are done yet, but I was told by mechanic that they are failing and that the fronts aren't spinning as smooth as they should when up on the jack. They were investigating a sticky caliper at the time and said they believe heat from failing bearing caused that issue. I figured I'd do a little looking for parts pricing just incase. Does come with everything needed to change it? From reading, I found part # 73CZ-1104B is that the one?
View 6 RepliesFord Super Duty (1999-2016) :: 2000 F250 - Wheel Bearing Conversion?
I have a 2000 F-250 SUperduty with a dana 50 front end , and as most of you know the front hub bearing's are junk, and expensive to replace. I know dynatrac has a kit to convert it to the tapered, cheaper, servicable bearing's. But 2g is a lil out of my price range. I was curious if anybody has tried takin the knuckles and stub shafts off an older dana 60 and putting the knucke's on the front axle to get the older bearing style instead of the hub bearing and the actuall lock outs instead of the POS vaccum style.
View 4 RepliesFord Super Duty (1999-2016) :: AC Compressor Is Not Engaging
2012 6.2 XLT 50,000 miles with manual single zone controls. I haven't had time to work on it yet, but it seems that my AC compressor is not engaging. The dash controls light up normal, fan comes on, etc. I am just looking to see if there are any common failure points. I know it COULD be low on charge, clutch could be bad, etc. I am just checking if there is a common failure with these trucks AC system.
View 10 Replies