Ford Super Duty (1999-2016) :: 2008 F250 - Hub Assembly Removal
I am trying to replace the ball joint on my 2008 f-250. Does the hub assembly come off of the knuckle or do you remove the whole knuckle and hub assembly together? If you have to remove the hub assembly what is the best way?
View 14 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Rear Blocks Removal
I want to know if there are any issues when removing the rear block, also do I have to put a new block in or can I just leave it out ....
View 12 RepliesFord Super Duty (1999-2016) :: 2004 F250 - 4x4 Shift Knob Removal?
I tried searching and googling but came to no results, unless its like similar trucks. How do the 4x4 shift remove? I have an 04 F250 and someone decided to put the shift on sideways so the 4HI and etc read upside down before I purchased the truck. Do I just rip the thing off?
View 1 RepliesFord Super Duty (1999-2016) :: 2012 F250 - Rear Seat Removal?
I would like information how to remove the rear seat back on a 2012 F250. I want to remove the head rests and from what I can find out they are bolted solid to the rear panel. I asked the same question earlier and got a reply for 2011, would that be the same? Is there any place I could get a schematic, a picture is worth a thousand words.
View 5 RepliesFord Super Duty (1999-2016) :: F250 - Brake Slide Pins Removal
I have a 1999 F-250 SRW 4x2. Is there a post that explains how to remove the front brake slide pins?
View 3 RepliesFord Super Duty (1999-2016) :: F250 Will Not Start After Removal Of SCT Flash Tuner
Yesterday I returned my F-250 SUPERDUTY 5.4 To stock on the sct flash tuner that came on the truck. after returning it to stock i tried to start the truck to leave about an hour later and instantly wouldnt start it backfired. we returned it back to the tune that was on the truck, still no start. we replaced the starter, the battery still nothing. if it sits for a little while it will attempt to turn over. it has a strong odor of gas in which led me to possibly thinking its vapor locked? or the pcm being bad or maybe the crank shaft sensor? the truck has ran strong and had zero problems up until now when we took the tuner off. it runs about 6 codes now, a few being the kam the o2 and low voltage.
View 4 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Front Bumper Removal?
i've done some searching but haven't found any how-to's or instructions on how to remove the front bumper on my 06 f250. Any link on how to do it?
View 2 RepliesFord Super Duty (1999-2016) :: 2002 F250 - Carrier Bearing Removal And Vibrations
I started with removing the two bolts that hold the carrier bearing to the crossmember that attaches on each side of the frame, well the clip that basically would hold the "nut part" of the bolt on the top side sheared on both of them due to salt+calcium chloride.
It felt like there was a 6 point head up there so I tried fitting wrenches and sockets up on the other side, I finally got a good hold with an 11/16" wrench but it just kept rounding more and more. Normally I would just torch the heads off but the gas tank is right next to it.
Any tips for getting the carrier bearing bolts out now? I don't care if I destroy it they're easy to replace. Also I'm typing this from my phone so Incase my sig doesn't show this is on my 02 f250 crew short bed 4x4
Ford Super Duty (1999-2016) :: 2000 F250 - Ignition Lock Cylinder Removal
I bought my 2000 F-250 CCSB a while ago and it came with 2 keys - one for the ignition, and one for the doors/tailgate - may not seem like a big deal, but it annoys me to no end.
From my understanding, the truck had previously been stolen and had the driver's side lock punched, and then something happened to the ignition lock to where it had to be replaced - hence the different key. I finally got around to replacing all the locks so that I'd only have one key. I started with the doors, then moved to the ignition (which I thought would be the easy part). I've replaced several cylinders before and I know it should be simple, but for the life of me I can't get the cylinder out!
I push the detent, turn the key to run, wiggle and pull.... nothing. I can feel the detent push in, and the cylinder will move a little, but it won't come out. I'm not sure if this is something that just happens sometimes and there's a fix for it, or if I'm in a unique circumstance and my column was somehow damaged during the theft and that's what's causing it.
Ford Super Duty (1999-2016) :: 2014 F250 - Rear Seat Back Removal?
I've got a 2014 f250 xl super cab and can't for the life of me figure out how to remove the back seat back.
View 2 RepliesFord Super Duty (1999-2016) :: F250 7.3L Diesel - Headlight Switch Pulls Out
When you turn the headlight switch to the headlight on position, you can pull it out exhibiting a positive click as if it is an additional switch for maybe optional fog lights. If the headlight switch is in the off or running lights only position, this will not pull out. I reviewed the elect. diagram but it does not show and addition circuit for the pull switch functionality?
View 4 RepliesFord Super Duty (1999-2016) :: 2006 F250 - Passenger Side Headlight Not Getting Power
2006 F250 and my passenger light was out. I thought it was a bad bulb and I wanted to upgrade anyway so I bought some Slyvania Ultra headlights. Pulled out the old bulb and it didn't appear to be broken, but I installed the new upgraded lights anyway. Still not coming on. I tried the hi beams and still nothing. Got an electrical probe to test the wires and still no juice. Where the wires run to so I can try to find the break in the line? I'm assuming there is not a seperate fuse for the passenger side...On a side note when I went hunting a few weeks ago I had some kind of animal make a nest under the hood, its possible a mouse/rat/squirrel ate my headlight wire, but the nest was in the top center of the engine by the turbo and oil filter.
View 6 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Drive Shaft Removal To Grease The Center Spline
I'm wanting to grease the center spline on my drive shaft. I got the 4 bolts off with a 12mm 16 point boxed in wrench but can't get the drive shaft loose from the rea rend. I don't blindly want to go beating it out of the yoke with a hammer to try to knock it loose (but I will if I have to). What am I missing to get this shaft out?
View 3 RepliesFord Super Duty (1999-2016) :: 2012 F250 4x4 - Front Passenger Side Wheel Hub Unit Removal
I need to replace the front passenger side wheel hub unit on my 2012 F250 4x4 120,000 mile reg cab truck. Its been a while but I did one on my 2000 F250 without any problems. There should be a few clips inside the hub that hold the looking hub and shaft together, right? Do I need any special tools for this job? What do the bolts need to be torqued to?
View 2 RepliesFord Super Duty (1999-2016) :: 2011 F250 - Electrical Lost In Cab After Headlight Bulb Replacement
I went to replace a headlight bulb and now I lost electric in the cab. I have no interior lights, no power window or door locks, turn the key on, no crank, no cluster, no radio, no chimes, the upfitter switches work, the mirrors power fold and telescope. Have power to both fuse boxes and battery is fully charged.
View 6 RepliesFord Super Duty (1999-2016) :: 2004 F250 - Driver Side Rear Sway Bar Link Upper Bolt Removal
I have a 2004 F250 Lariat Crew Cab FX4 6-3/4' bed.
What is the procedure to remove the Driver's side Rear Sway Bar Link upper bolt? - the link attaches to the frame. The nut is on the inside of the frame with about 1/3" to 2/3" clearance between the frame and the fuel tank. Of course, the frame's "C" shape faces towards the inside.
Ford Super Duty (1999-2016) :: 2014 - Removal Of Bed Stickers?
I want to remove the 4x4 stickers on my 2014 SD box. I think it looks cleaner without them. Are they difficult to remove or does the hair dryer trick and then some Goo-Gone do the trick without a big time effort? The last thing I want to do is make a mess of the paint finish.
View 13 RepliesFord Super Duty (1999-2016) :: Tailgate Handle Removal?
Looking to get rid of the step handle, I did this mod on mine and it was a direct fit...take off old liner and unbolt handle, then get a liner from a non-step tailgate and it is a direct fit:
View 7 RepliesFord Super Duty (1999-2016) :: Transmission Line Removal?
OK, so I ordered in the new lines and have them. BUT my problem is snaking the factory transmission line out from under the truck. I have pictures to show my struggles.
How do I pull this:
Out of here???
Towards the front of the motor
Front passenger side cab corner
Replacing these lines? I don't care about breaking the old one, but I still need to find a way to install the new one.