Ford Ranger / B-Series :: Loud Speed Dependent Noise - Bad Wheel Bearing?
I have an 01 Ranger 4x4 that recently started to make a loud speed dependent noise from the drivers side front wheel, a quick jab to the right on the steering wheel and it stops, straiten out and it comes back...since I know my shocks are worn and have some cupping on the front tires my first thought was tire noise so I moved the back tire which is evenly worn to the front and no change, next I removed the tire and checked everything visually.
All seems ok, the brake does not seem to be dragging and there is no evidence of a cv problem, everything seems tight, so I'm guessing the problem is a bad wheel bearing? If I grab the tire at 12 and 6 there seems to be excessive movement from top to bottom, there should be none right? If memory serves any movement is indicative of bad wheel bearings? I guess I'm looking for some vindication before getting a new hub?
Ford Ranger / B-Series :: 1999 - T/O Bearing Making High Pitch Squeal Noise
The T/O bearing makes a high pitch squeal until you put light pressure on clutch then it will go away. Does this thing have a preload on bearing at all times or should there be free play like in the old days??
Another thing that has me wondering is when I push clutch all the way in it actually puts a load on the engine. Having T/O bearing so bad it puts a load on the engine?
Ford Ranger / B-Series :: 1993 - Clutch Release Bearing Install
93 Ranger, 4.0 liter, 4WD.....
Putting in a new clutch and clutch release bearing, and am wondering if I need to put the retaining ring in that came with the new clutch release bearing? When I took off the old release bearing, a ring did come off from somewhere, but I did not see where it was because it was so dirty.
The reason I ask is because my Haynes manual did not even mention a ring, so I was surprised to see one come off. And my manual does not say to reinstall the ring when installing the release bearing. I did get a newer Haynes manual at the library and looked through a bunch of Chilton, etc manuals.
The newer Haynes manual says to remove the retaining ring on 97 and newer models, but says nothing about putting it back in when reinstalling. So, I am not certain if I need to put a new retaining ring in with the new release bearing.
Ford Ranger / B-Series :: Steering Wheel Lock Damaged - Popping Noise When Turning
While in the locked position, the steering wheel was purposely jerked hard to disable the mechanism on a 1996 Ranger. Now the truck will not steer easily or smoothly and a popping noise is evident when turning. I'm not concerned about having the wheel lock, but would like to be able to return driveability to normal.
The same guy who caused this damage also damaged the ignition. No key is needed to turn the switch now.
I'm lost as to how the steering locking mechanism works and wondering if I need to tear apart the column or if maybe there is a locking pin accessible that needs to be removed to regain driveability.
Ford Ranger / B-Series :: 1995 - Replacement Of Carrier Bearing On Drive Shaft?
I am driving a 95 ranger xlt extended cab with a 3.0 two wheel drive with an automatic transmission. the two piece drive shaft with the carrier bearing went bad at the bearing. i separate the u-joint just after the bearing and was going to remove the nut holding the bearing housing together but cannot get the nut off. now i'm also finding out that i need a bearing puller to remove the damaged bearing from the 1st drive shaft.
Its turning into something i may not be able to finish. i saw on line an idea where a guy replaced the 2 piece shaft with a one piece. he states that a 1 piece drive shaft, 1998 or newer would work and no need for this bearing. you have to remove the cross member. it sound easier than what i'm trying to do. i looked at some old posts and galleries but did not see an article. here is a link to his website: How-To: Swapping a 2-Piece Drive Shaft for a 1-Piece in a 1983-1997 Ford Ranger
Ford Ranger / B-Series :: Two Piece Drive Line / Center Carrier Bearing Going Out
My 96 ranger with a 5 spd manual and two piece drive line has the center carrier bearing going out (squeals,vibrates,etc.) I got the part no. from the dealer but they are obsolete. is there a one piece drive line i could put in and what would that take to do.i remember a thread on it somewhere but cannot find it in the search. i would prefer not to use aftermarket because they only have a one year warranty.
View 10 RepliesFord Ranger / B-Series :: 1983 - Vibrates Around 35 MPH - Shaft Bearing Broke - Replace Trans?
I noticed a strange vibration in the 83 Ranger I own, it has the 2.3 and a 4 speed. When getting up to speed around 35MPH it would start vibrating, and the speedometer needle would bounce around and read slower than it was actually moving. This would start in 3rd gear, and continue thru 4th unless I let off the gas while it was in gear, then it stopped and worked normally. I put a grease seal in the tail section when I first got the truck, and when I pulled the driveshaft again today the seal was mangled and bent, plus there are metal particles around the main shaft where the seal goes. I figure the tail shaft bearing is shot, and I also found damage to the yolk with the U-joint, the shaft has a worn spot about 1/3rd the way around.
View 2 RepliesYaris/Scion & Vitz :: Wheel Bearing Noise / Vibration On The Front Left (driver Side) Wheel
So on my girlfriends 2000 echo I get the classic bad wheel bearing noise/vibration on the front left (driver side) wheel. Worsens under load (right turn) and goes away when unloaded (left turn). I've replaced left side bearing, CV axle, brake rotors/pads and the noise still persists. My next thought is maybe the ball joint but humming/vibration tells me something out of rotational balance. Bearing in the transmission? I don't know. I'm stuck.
View 5 RepliesFord :: Repetitive Whirring Noise From Right Back - Wheel Bearing?
2006 Ford Focus with an ongoing wheel bearing issue. Earlier this year I heard a repetitive whirring noise from the back right, figured it was a bearing, brought the car in for repair. The shop confirmed and replaced the bearing.
3 months later, I heard the same noise. I brought the car to a different shop (I had moved since) and they confirmed that it was the same wheel bearing that had just been replaced. They said it may have been faulty. They attempted to repair it, but the noise persisted. They actually ended up putting the new bearing on the driver's side rear and swapping out the old bearing that was on the driver's side with old one on the passenger's, which is the only way they could get the noise to stop entirely. (This confused me)
Fast forward two months and the noise is back on the same side - passenger's rear. The shop is telling me that it is unrelated since the new bearing was technically put on the other side, however, I am thinking that the same thing keeps happening whenever any bearing is put in the same spot (passenger rear). My question is as follows - what could be happening in the passenger rear that would cause bearings to continually fail?
Ford Excursion :: Hub / Wheel Bearing Noise - Clicking Sound
Not my video, but I have the same exact sound coming from my passenger side wheel on my 03 V10 4X4, 130K. Passenger side only, no noise from the other side.
YouTube .....
Before I spring for the Timkin, does this sound like a bad bearing? No play in the wheel, but it's a clicking sound.
Ford - Explorer :: Thumping Noise From Front / Wheel Bearing?
I have a 03 explorer with approx 160k, I am experiencing a thumping noise while driving. It gets worse on right turns and gets better on left turns. initially i thought LF wheel bearing so i ordered a hub assy and replaced LF. noise is still there. I guess, thumping noise caused by wheel bearings, i know its usually a grinding kind of whirring noise.
The noise doesn't seem to change with accel/decel so I don't think it is driveline related (diff, drive shaft etc.) should i bite the bullet and replace the rf as well??? I should also mention that there is also a shake in the steering wheel that seems to coincide with the thumping (i.e., my hand shakes along with the thumping, and the shake gets worse when the noise does)...
Ford 6.7L Power Stroke Diesel :: Wheel Bearing Gone Out - Making Noise?
Wheel bearing go out? My left front just starting making noise and when turned by hand you can hear the bearings are shot. Called around this morning and with my luck its on back order and the entire hub has to be replaced since the bearing is built into the hub.
Anyways, I was wondering replacing this unit themselves and how long it took to complete? I was going to let Ford do the work but I figured I have never done a job like this and wanted to give it a try and looking at some Youtube videos on older vehicles it did not look that difficult.
If I find that its not difficult I will tackle the other side as well since I figure it is probably not long before that side is gone also and I would not want that to fail while I am out towing somewhere.
Ford - Explorer :: 2003 - Grinding Sound Like Wheel Bearing Noise
I have a 2003 Sport Trac 4wd with 299,000 miles. There is what sounds like wheel bearing noise (grinding) that was noticed after returning from a trip where I flat towed it behind my rv. I did not notice the noise the last time I drove it - before towing it about 450 miles. I have towed this vehicle for many years and miles this way - transmission and transfer case in neutral with key in on position to unlock steering. I stated this part about the towing because the noise may have gone unnoticed for many miles. About 20,000 miles ago, I changed front wheel bearings, brake calipers, upper and lower ball joints, shocks and outer tie rod ends. Also rear brake pads.
I put the vehicle on jack stands and in drive mode couldn't hear anything in either 2wd or 4wd. I held one wheel at a time so the other side would spin. After checking for wobbling wheel bearings, I took off the wheels and did a push / pull on everything - all seems good. I changed driver's side wheel bearing anyway because I thought it to be a little rough. I removed the front drive shaft and took it out on the road. Noise was still there. This makes me think front differential but before entering unknown territory (for me) is there something else I can do to narrow down the problem? At this point, I'm not even convinced it is from the front end - maybe the sound is radiating through the truck.
Ford - Explorer :: 2002 - Front End Is Howling / Wheel Bearing Noise?
I'm working on a 02 explorer. The front end is howling so I replaced the left side and no change. The howl goes away when braking. Is it the right side then or something else? I replaced both front brakes pads so it's not that.
View 2 RepliesFord Transmission :: 1994 Explorer - Outer Front Wheel Bearing Noise
I have a 94 Explorer. I recently swapped over from auto to manual hubs. I followed a detailed write-up that I found online. During the process I repacked my outer wheel bearings. Ever since then I hear a grinding noise coming from the front wheels. Sounds like the bearings aren't seated properly. The guide that I followed instructed to torque the spindle nut that sits next the the outer wheel bearing really tight in order to seat the bearing, then loosen it back up and hand tighten it. But when I loosened the spindle nut the wheel bearing would pop back out. What is the best way to get a wheel bearing to stay seated properly?
View 2 RepliesFord Ranger / B-Series :: 1991 - Front Hub Comes Off With Wheel?
I recently bought a 91 Ranger 4wd for my son. The guy I bought it from put new manual lock outs on it. every time I take the tire off on either side the hub comes with it! Is there a clip or retainer missing? If so what and where can I get one?
View 4 RepliesFord Super Duty (1999-2016) :: Rear Wheel Bearing Making Noise
Have a rear wheel bearing making some noise. A friend told me that it is always the outer bearing that goes first . Can you replace the bearing without replacing the race?
View 14 RepliesFord Ranger / B-Series :: 1997 - Vibration Feels Like Wheel Hop
I'm having a bit of an issue with my 97 ranger 4.0 auto 2wd. I have an vibration which from a stop up about 10 mph feels like wheel hop not bad but you can definitely feel it it and over 50 mph the whole truck starts to shake again not bad but you know its there. the truck sat last summer it was my dd till a bought a new car and now vw is buying it back ill be driving the ranger in the mean time. I have been trying figure it out for a few months but no luck i have put new tires , front rotors and rear drums , drive shaft support bearing ( 2 pc shaft) new u-joints and a used boneyard shaft with new u-joints as well, checked the tail shaft bushing which had about .008" of play.
Pulled the drums Off today and checked the axle bearing for play only .004" of play pulled the diff cover and checked for carrier play as well as pinion play but can't find anything. I'm at a loss here and looking for other things to check ... Don't know if its possible that something in the transmission is loose it was rebuilt about 75k miles ago I was going to stop and talk to the trans shop to see what he thought (its a 5r55e ) ....
Ford Ranger / B-Series :: 1992 - Wheel Cylinder Blowing Out?
'92 Ranger 2WD with 4 cyl and 9" brakes, right rear wheel cylinder keeps blowing out, replaced it twice. I've thought about maybe an obstruction in the left brake line creating too much pressure, or in the junction block on the rear axle. I believe only one line leads to there from the master cylinder, so what else could it be? Only other thing I can think of is that the right brake has a mechanical problem which is causing the forward shoe to move too far away from the cylinder, leaving no 'stop' so the piston just slides right out of the cylinder. But I can't figure that. Original adjuster star wheel was chewed up so I swapped in another, doubt it's that.
View 14 Replies