Ford - Explorer :: Thumping Noise From Front / Wheel Bearing?
I have a 03 explorer with approx 160k, I am experiencing a thumping noise while driving. It gets worse on right turns and gets better on left turns. initially i thought LF wheel bearing so i ordered a hub assy and replaced LF. noise is still there. I guess, thumping noise caused by wheel bearings, i know its usually a grinding kind of whirring noise.
The noise doesn't seem to change with accel/decel so I don't think it is driveline related (diff, drive shaft etc.) should i bite the bullet and replace the rf as well??? I should also mention that there is also a shake in the steering wheel that seems to coincide with the thumping (i.e., my hand shakes along with the thumping, and the shake gets worse when the noise does)...
Ford - Explorer :: 2002 - Front End Is Howling / Wheel Bearing Noise?
I'm working on a 02 explorer. The front end is howling so I replaced the left side and no change. The howl goes away when braking. Is it the right side then or something else? I replaced both front brakes pads so it's not that.
View 2 RepliesFord Transmission :: 1994 Explorer - Outer Front Wheel Bearing Noise
I have a 94 Explorer. I recently swapped over from auto to manual hubs. I followed a detailed write-up that I found online. During the process I repacked my outer wheel bearings. Ever since then I hear a grinding noise coming from the front wheels. Sounds like the bearings aren't seated properly. The guide that I followed instructed to torque the spindle nut that sits next the the outer wheel bearing really tight in order to seat the bearing, then loosen it back up and hand tighten it. But when I loosened the spindle nut the wheel bearing would pop back out. What is the best way to get a wheel bearing to stay seated properly?
View 2 RepliesFord Excursion :: Hub / Wheel Bearing Noise - Clicking Sound
Not my video, but I have the same exact sound coming from my passenger side wheel on my 03 V10 4X4, 130K. Passenger side only, no noise from the other side.
YouTube .....
Before I spring for the Timkin, does this sound like a bad bearing? No play in the wheel, but it's a clicking sound.
Ford - Explorer :: 2003 XLT - Rubbing Or Light Grinding Sound When Put In Park
I got a strange one. 03 expl 4x4 xlt, started making a weird sound, almost like a rubbing, or a light grinding, comparable to the sound and seat of the pants feel you would get if say you ran out of good brake lining and were creeping the car forward at half mph while dragging the breaks slightly but (except it is when you are stopped and in P). Break pads are fine, just when you come to a stop and put it in park. lasts for about 1-3 seconds. No tranny slippage or other issues yet, all seems to be working. I don't use 4x4 hardly at all but not in last 6 months since there is no snow. Since it is so short I cannot pop the hood to track it down. Torque converter? Fan clutch?
View 3 RepliesExplorer :: 2000 - Grinding Sound Coming From Front Right Side / Steering Wheel Shaking
I just recently bought a 2000 Explorer, 4.0 OHV, 4x4 with about 150,000 miles.
I've had the vehicle for about a month, and ever since I bought it, it's had a grinding sound (sounded like wheel bearing) coming from the front right side. I replaced both right and left bearing/hub assemblies, and took it out for a drive. The initial sound that I thought was bearing noise is still there, and at about 65mph I started to get a little bit of steering wheel shake. I took my foot off the gas and it stopped. I accelerated up to about 70mph and it seemed ok.
I hit a VERY small bump in the road and the steering wheel started shaking like hell. So bad that I almost lost control. I slammed the brakes and the shake stopped instantly. I took it home and put it up in the air, half expecting to see something loose or broken, and everything looks perfect. I re-torqued everything that I had taken apart for the initial hub/bearing replacement, and took it out again. Same issues.
I never had ANY of these problems before I replaced the hub/bearing assemblies, so I'm completely confused. I was thinking CV joints, but I have no clicking at all when turning, in forward or reverse, everything is smooth. Outer tie rods were done about 6 weeks ago..
Ford - Explorer :: 2003 - Grinding Or Humming Sound Coming From Left Driver Side Front
Alright so I'm having a problem with my 2003 Ford Explorer. I've recently noticed that when I get to above 40 mph, if my steering wheel is straight, I hear a loud kind of grinding or humming sound coming from my left driver side front. If I am going about 65 mph, it gets even louder and if I crank the steering wheel to the left, that's when it really gets noisy but as soon as I crank it to the right, the problems gone. When I do hear the hummin sound, I can feel it in the steering wheel. I have replaced al of the tires and it didn't work. Also, the car slightly pulls me to the right.
View 10 RepliesFord F-150 (2004-2008) :: Repeated Front Hub Failures - Wheel Bearing Grinding
Repeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!
Ford - Explorer :: 1999 - Front Wheel Bearing Nut Size?
1999 explorer Eddie bauer. Front wheel bearing nut size? 33mm?
Looking for a torque spec procedure. Need to replace an abs sensor. Sensor alone was 120 bucks so just bought the whole hub assembly with sensor. Might just put the whole thing on.
Is there a good thread for a complete socket size portfolio on the explorers. Thinking sizes over and above normal socket sizes found in your typical socket set?
Ford - Explorer :: 1997 4x4 - Rumble Up Front Above 90 Km/h - Wheel Bearing?
My wife's Explorer 4x4 has a noise in the front at around 100km/h. It is not detectable below 90km/h. Its not noticeable from a standstill until around 100, then you hear it a little. I find I can make it more noticeable if I vary my speed from 110 to 105 up and down, then its easier to hear. Once you get below 90 km/h you cant hear it at all.
I have a broken leg right now, and I normally do ALL my own work so I'm a little-limited mobility wise at the moment.
I'm suspecting a wheel bearing. I put the Explorer in the garage and my son jack up both wheels on the drivers side. I started the engine and SLOWLY accelerated up through the gears to 100. I know the hazards with this as I've done it with other vehicles, but this was the first 4x4. Then we jacked up the passenger side (after lowering the drivers side) and did the same thing. I could slightly hear/feel the rumble when the passenger side was jacked up.
I did drive the vehicle on my outdoor ramp/pit so I could use my crutches and get underneath to have a look. I grabbed the cv axles and they feel solid. The propeller shaft was replaced last year, and the cv axles look brand new. (bought the vehicle off a friend two years ago.).
So, are my suspicions correct, is it the pass. side wheel bearing? The Explorer has 294000kms. Never did test it on corners as I didn't want to swerve back and forth on the highway with the amount of traffic.
Ford F-150 - 1997-2003 :: Horrible Grinding Noise When Turn The Wheel Either Direction
I may, or may not have had to jump a curb at 40 mph to avoid rear ending another car. Truck is a 2003 F-150, single cab stx package, 4.2ltr. Long story short, no damage to my passenger side front tire or rim that I can see, but I do have a horrible grinding noise when I turn the wheel either direction. The truck still turns properly, power steering fluid is level. What should I start replacing first?! She's got about 90k miles on it, I'm sure a lot of the suspension parts are due, just need to know where to start!
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Grinding And Metal Chewing Sound Coming From Front Axle Or Close The Wheel Hubs
I have 1999 F350 7.3 Crew Cab 4WD. I took it on a 4 hours trip towing a trailer to haul a small tractor on it. after 3 hours of driving, I started hearing grinding and metal chewing sound coming from the front axle or close the wheel hubs. It was awful, terrible, ... you name it!!! I had to continue or I will lose the tractor I paid for already. The sound was coming for 1-2 seconds each 500 feet or so. It never stopped or changed. I pulled over to see what's going on and found the following:
1. Left shock is leaking badly
2. Right locking hub is gone (not sure if the truck had one before). I bought this truck last year, but I never had to use 4x4 and I know the 4x4 motor by the transfer case is missing and the nipple on the transfer case is set to the 2wd position so the front drive-shaft does not turn.
I took the front shock off and continued to drive without it, the noise did not go away.
I pulled over again and this time I noticed that the dust cover on each end of the front axle is missing too. I have never worked on these axles before, but I jacked one side, and sure enough, gear oil was leaking from the other side. I took the plug off the front differential and stuck my finger in it. I felt a creamy brown-greenish stuff in the differential. The consistency is like mayonnaise or thin peanut butter. I put the plug back on and went to pick up the tractor because I did not want to miss it fooling around with the truck on the highway.
The truck made it there and back (almost 5 hours total after the break down). The sound never stopped every 500 to 1000 ft.
After getting home safely, I took the other locking hub off, and took it for a test drive. I did not hear the noise, but now my right brakes are locking.
I took of the wheels and saw that the retaining snap ring (C clip) for the front axle on the right side came off by hand. I took the washers behind it off. Took the calipers and brackets off. I have never done front axle rebuild. I am not sure what has been damaged and what's still good.
Right of the bat, I know, at least, I need 2 shocks, one brake caliper and pads.
My questions are:
1. Is it possible to take the front axles off on both sides and make it 2wd for now until I have the money to rebuild the axle?
2. Could I use the same hubs? or they are most likely damaged and how to tell?
3. How to tell if the differential is damaged/needs rebuilding?
4. How to tell if the axles/spindles are damaged?
5. Is there a step by step tutorial to rebuild the axle with all seals, bearings, ...etc? How hard is the job for a hobbyist? I do most of my repairs myself, and I was lucky at 36 years old, I never had to rebuild a differential.
6. What else I might have damaged in the process of driving it that long with the noise? How do I tell if I did?
Ford F-150 (2004-2008) :: Bearing Noise - Constant Grinding / Whine
We've had a lot of rain here in pa lately and i hit a few big puddles the other day and now i have a growl slash wine in the front of my motor,now i narrowed it down to something driven by the bely because I removed the belt and no noise all pulleys feel good and smooth except the ac compressor if you spin it by hand it has a rough/dry feeling and sound to it but the noise doesn't change with the ac on or off its just constant grinding/whine. Replace the ac compressor pulley bearing that what I am thinking it is and don't really want to change out the whole compressor..
View 1 RepliesFord - Explorer :: 2000 - Making Bearing Noise?
2000 Explorer making what I would call a bearing humm. I have replaced both front wheel bearings over the past year. When I jack up the front and check for play everything is tight, I don't get any noise by spinning the tires. While driving I put the tranny in neutral and still get the hummm sound, so I don't think it is the tranny.
The sound definitely changes with the speed of the car. Turning the wheel or engaging the transfer case do not change the sound. I have had my son crawl around the car while I'm driving and he said the sound is not coming from the back, for sure the front but can't tell if it is specific to one side of the other.
Where do I go from here? This is my daughters daily driver and its been a great car, 148000 miles and no issues at all so far. I would like to figure it out so I can feel good about her driving the car.
Ford Excursion :: Growl Sound Like Front Left Wheel Bearing
I have been having towing with the X. I have been getting a growl lately sounds like the front left wheel bearing. Today I jacked it up and did the wiggle text. I have a very slight wiggle in both wheels. Is a slight wiggle normal? I know the bearing on the left is more than likely gone as the growl goes away when I jerk the steering wheel. But I haven't heard any noise from the right side yet.
View 14 RepliesFord - Explorer :: 2003 - Pinion Bearing Has Started To Go / Whine From Rear End
I have a 2003 explorer where the pinion bearing has started to go, now the rear is starting to whine. the truck is a 2003, its a limited, with the 4.6 v8 in it. I would like to swap the rear with another used one, rather than rebuild the diff. the car is AWD, has a hitch receiver so I would imagine it has the tow package, my question is could I grab a rear out of a non AWD explorer, or one that had the 4.0 in front of it? something with the same gear ratio but out of a similar, non exact car, it has the advancetrac in it with the push button on the center console.
View 3 RepliesFord F-150 (2004-2008) :: 2007 - Speed Related Ticking Sound / Wheel Bearing?
The front driver's side wheel of my 2007 Ext. Cab makes a speed-related "ticking" sound. It's usually audible but not always there. I look for rocks in the tread of my BFG All-Terrains and sometimes I find some, sometimes not. The noise seems to be independent although some of the rocks really get up in there. Sometimes its really loud and it sounds like a rock. Bearing? 4WD CV or U-Joints or whatever?
View 6 RepliesGolf V R32 :: Whoop Sound From Wheel Bearing
Alright a few weeks ago I had right wheel bearing replaced...noise still there... Had tires balanced, rotated, checked for capping. The dealer hears the noise but can't tell where its coming from.
The sound is classic wheel bearing Whoop Whoop Whoop and I can control it when I turn to the wheel right and left. This will be the fourth time its in the shop.
Yaris/Scion & Vitz :: Wheel Bearing Noise / Vibration On The Front Left (driver Side) Wheel
So on my girlfriends 2000 echo I get the classic bad wheel bearing noise/vibration on the front left (driver side) wheel. Worsens under load (right turn) and goes away when unloaded (left turn). I've replaced left side bearing, CV axle, brake rotors/pads and the noise still persists. My next thought is maybe the ball joint but humming/vibration tells me something out of rotational balance. Bearing in the transmission? I don't know. I'm stuck.
View 5 Replies