Ford Ranger / B-Series :: Check Engine Light Came On / Code P1443
I have a 1997 Ford Ranger and my Check Engine Light came on a while back. So I eventually bought a scan tool and I'm only getting one code which is P1443. I've looked at both my Chilton and Haynes Manuals, my Ranger manual itself which is pretty useless for this problem, and I've been searching the internet like crazy.
From the threads I have read here it doesn't seem like a hard problem to fix yourself, and it seems like if you take it in anywhere they will charge you an arm and a leg to work on the EVAP system but it's an affordable do it yourself project.
I just don't know where to begin though, I see people talking about buying the complete set with hoses and the canister and sensor all together but I can't find all these parts. Where do I begin to repair the EVAP system?
Ford Ranger / B-Series :: Losing Full Power Like Cutting Out While Under Acceleration - Code P1443
97 ranger 2.3l ... I have a problem where I'm losing full power (like cutting out) while under acceleration it's only for a split second almost like a hesitation. I got p1443 for the first time today and I was looking at my fuel trims and I noticed my long term FT is at 99.2% and never changes while my short term goes between negative and positive no more than 6%positive and like -4% I assume this is normal for short term but I really am just guessing on that. I am thinking perhaps I need a new fuel pump...but maybe I'm wrong...truck has a new fuel filter and a new evap purge solenoid...
View 14 RepliesFord Aerostar :: 1997 - Got Codes P1443 / P1443?
finally found the reasons for the two Codes in my '97 4.0.
here are the culprits: Code P401 DPFE Sensor, found it on eBay. (The metal case sensor, nos)
Code P1443 Evap system Purge Sensor (also eBay)
Finally, CEL is off after replacing both sensors above.
Now I have to figure out the REAR ABS light, still ON.
Ford Aerostar :: 1997 - Code P1443 For EVAP System
My 1997 aerostar 3.0 6 cylinder, throwing code p1443 for the evap system. What should I be looking for?
View 5 RepliesFord Ranger / B-Series :: Code 157 For MAF Sensor
So here is what I got. Code 157 maf sensor below minimum voltage. Here is what the truck does. When the MAF is plugged in and I step on it, the truck surges and when it drops below 1k rpm it dies but I can start it back up. If I hold the throttle at 1k it stays alive. When I drive with the MAF unplugged it runs better no surging but it still dies. Here is what I have done. Reset codes no change, put new MAF in no change. I have traced all 4 MAF wires checked continuity from inside of plug to inside of plug.
All wires checked out good. No cuts breaks or anything. I have checked my battery, starter, and alternator ad all check out fine. I read that someone said if the corresponding transistor in the PCM took a dumb then it would cause not enough voltage to get to the plug because the transistor would dump the voltage from the battery leading to the MAF. I thought about running a direct power source from the battery to the voltage side of the MAF with a switch in the truck to just see if that would solve the issue but I don't know if that is possible or smart.
Ford Ranger / B-Series :: 1997 - CEL With Code P0133?
I have a 1997 Ford Ranger with a 4.0L 2WD. The check engine light just turned on with a code of p0133. I know that this is something with the bank 1 sensor 1. I tried doing some research and I think that it is on the passenger side before the cat converter. Now, I don't know what to do from there. How do I go about fixing this? What part do I need? How do I fix it?
View 1 RepliesFord Ranger / B-Series :: 2001 - Airbag Code 29
What airbag code 29 on a 2001 ranger means? I have not seen that number on any code lists. I triple checked the code and it is 29.
View 9 RepliesFord Ranger / B-Series :: Got Code P0162 - O2 Sensor Or MAP?
Just checked SES code and read P0162 I think. Stated rich fuel mixture bank 1 & bank 2 (3.0) Is this an O2 sensor or MAP issue?
View 8 RepliesFord Ranger / B-Series :: 1995 - CEL Came On - P0340 Code - CPS Bad
I am having an engine issue with my 1995 Ranger with a 2.3L. I have been having a P0340 code that kept appearing after several attempts at resetting the PCM. I gave up and took it to a Ford dealer for diagnostics and they called the CPS bad. They changed it, but the CEL light immediately came on with the code still kept coming up. The service rep. showed me the old sensor, it had a spot on the head of it where it looked like something was rubbing it. I'm assuming it's slightly rubbing on the gear it points to, which is the oil pump gear, correct? The truck runs fine, no performance issues whatsoever. Is it possible my oil pump shaft has developed play in it's shaft, causing this?
View 1 RepliesFord Ranger / B-Series :: 1994 - How To Check Code For CEL
1994 Ranger xtra cab
4x4
v6 4.0
5-speed
113K miles
Just bought this truck. When I test drove it no "check engine" light came on, but after purchase driving home is came on and then off many times. It only comes on at high rpm/speed. I have my trusty ODBII scanner but realize that this 1994 was pre-ODBII. How can I figure out what the CEL is about?
Ford Ranger / B-Series :: Code P1403 Keeps Coming On After Clear It
My 96 4x2 2.3ltr is throwing this code (P1443). I clear it and it comes back a few cycles later. I will fix it next but won't be able to get to it for a couple weeks. What if any affect does this code have on fuel mileage and or engine performance/power?
View 3 RepliesFord Ranger / B-Series :: 1999 - Airbag Light On With Code 32
My son has a 99 Ranger where the airbag light is flashing code 32. I had the same code on my F350 and it was the clock spring. What it could be. It is 99 Ranger with 2.5l, auto trans, 2wd, no CC.
View 2 RepliesFord Ranger / B-Series :: 2008 - CEL Code P0304 / Misfire
2008 Ranger 3.0L. I am trying to figure my next step in diagnosing a #4 misfire. At regular speeds I really dont hear it or feel it, mostly at idle warm or cold. 3.0L with 275,000 kilometers on it , reg oil changes.The CEL is on, but not blinking. Pulled a p0304 code. I then changed out the bosch plugs I had in with ford plugs and wires. The #4 plug looked okay just bigger gap. Still got the code.
I hooked up a sparkplug light to the coilpack and did not see any missing flashes . Changed fuel filter, checked fuel pressure,all within specs. Changed the oil and did not see anything in it. I read that it could be an injector but I have to remove the intake manifold to get at it. I also read to check compression. I figured if I have to take off the manifold I would put a new injector in, instead of switching them around. What is the most common cause for this code?
Ford Ranger / B-Series :: 1998 - CEL On / Pending Code P0446
Today my Check Engine Light came on for the first time in years on my 1998 Ford Ranger. It has 363,000 miles on it. But the engine was changed about 150,000 miles ago. It's a 2.5 automatic. It runs good and has no problems until today. I was leaving a shop and when I started up the truck the Check Engine Light came on. It wasn't idling bad but when I went to take off it wouldn't hardly move. I wasn't even able to keep driving. So I stopped and turned it off and restarted it. Then the Check Engine Light was gone and it ran fine. I scanned it when I got home and it a Pending code of P0446.
I've never gotten this one before. It said something was wrong with the fuel vapor vent solenoid open or shorted. I've never replaced anything on the evaporative emission system except a hose under the hood 3 or 4 years ago. I've had to change the fuel pump a couple times. I've never had any wiring issues. I've never hacked into the wiring. I've owned it since it was new. Is it likely that solenoid is failing or the vapor canister is shot? I don't need this to happen again because even if it's in what was called limp mode. there's no way I could've driven it home like that. I couldn't even pull over. I was lucky I was still in a parking lot.
Ford Ranger / B-Series :: Code P1451 - Vent Solenoid?
So... p1451. Vent solenoid. I pulled the part and put 12v to it. Opens/closes just fine. Checked resistance on part, 55ohms like it should. Pulled vent canister, no apparent leaks or blockages. I traced wires back to cab. Cannot locate anybroken wiring. I looked up the pinpoint test on this dct and all thats left to test out is the pcm itself. Before I buy the obd2 scanner with all modes I wondering if I am missing something.
I did find a broken ground wire in my searching. Frame to body. My thoughts on a bad ground are that that would cause more than one monitor to register one fault code.
Ford Ranger / B-Series :: 1997 - Got B2300 / P0420 Code
I have a 1997 Mazda B2300 with 175,000 miles that has an intermittent check engine light. When I check the code it is always P0420. If I leave it alone long enough the light usually goes out. The truck had the catalytic converter replaced about 5 years and 60,000 miles ago. I also had the muffler replaced in October, but I was getting this code prior to the muffler replacement. I recently bought a scanner that can monitor the fuel trim data and noticed that the long term fuel trim is generally between +16 and 18%. I replaced both oxygen sensors last week and cleaned the MAF sensor, but today I got the CEL again. The LTFT is also still the same as it was before I replaced the O2 sensors. My truck doesn't use any noticeable amount of coolant or oil and I'm not really sure where to start.
View 8 RepliesFord Ranger / B-Series :: 1992 - Code 212 With CEL - No Power On Acceleration?
I have 92 ranger with 3.0 v6 in it.
It flashes out code 212 ive replaced the ICM and checked the spout connector for corrosion but it still flashes out 212 and has a rough idle no power on acceleration condition.
also when the idle starts acting up the check engine light stays real dim and if you rev it it will get brighter
Ford Ranger / B-Series :: 2006 2.3L - Code P2195 / O2 Sensor
I have a 2006 Ranger 2.3l 4 cylinder that is have emissions problems the code the tech gave me was P2195 an I bought the o2 sensor just where it is, and the auto stores didn't have a manual for the year of my truck.
View 2 RepliesFord Ranger / B-Series :: 2000 - Idle With Code PO171?
2000 ranger 2.5 stick, coming to a stop i put in the cluch and the motor speeds up then slows down sometimes more sometimes less.
A month ago I had a code PO171, with a good idle. I cleaned the MAF senser then cleared the code, a week later the the CIL came back on same code. Then a month after the CIL is on the engine idle problem started. So I recleaned the MAF with MAF cleaner, cleared the code, and replaced the ICV with a new one. That worked good for about 3 days now the idle problem is back again.
The idle problem seam to be worse when the motor is warm or has been running at freeway speeds.