Ford Ranger / B-Series :: 1998 - Serpentine Belt Squeaking
So i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 RepliesLexus ES 2007-12 :: Serpentine Belt Replacement Procedure For ES350
I have a 2007 ES350 with over 65 k miles on the clock. I would like to change the serpentine belt as a preventive measure. Looking for a procedure on changing this belt? Pics ???
View 4 RepliesOldsmobile - Cutlass :: Serpentine Belt Starting To Shred - Replacement?
I had my serpentine belt replaced 3 months ago because it was starting to shred. Yesterday it broke again. The garage said the second time was caused by a problem with the crankshaft pulley. Shouldn't they have noticed a problem with the crankshaft pulley the first time it was replaced?
View 5 RepliesCamry :: Idler Pulley Replacement On Serpentine Belt Tensioner
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 RepliesFord Ranger / B-Series :: 2003 - Engine Does Not Want To Start After Belt Replaced
I have a 2003 Ranger 2.3l with 327k miles on it. I recently replaced the belt and now it doesnt want to start. The belt is on correctly and tensioner is tight. The battery is fully charged its just not firing up and starting. All connections are good, the ac and power steering pulleys are relatively new. Now i have been stuck tryin to fix it for a week...
View 8 RepliesFord Ranger / B-Series :: 2003 - Unhooking Seat Belt Buzzer
I recently bought a 2003 Ford Ranger. What I want to do is unhook the seat belt chime. In the past with the other 3 Rangers I owned I unplugged it from under the seat. But when I unplugged this one the light for the air bag stayed on. I like the freedom to choose and I don't care for the chime.
View 14 RepliesToyota - Camry :: 2006 - Water Pump And Serpentine Belt Replacement
Is it possible to change the water pump and serpentine belt in a 2006 Toyota Camry with 4 cyl. engine in less than an hour?
View 4 RepliesFord - Ranger :: 1997 - Vacuum Lines Coming Close To Hitting Serpentine Belt On The Front Of Engine
Ok, I have 1997 Ford Ranger, 4cyl, manual transmission, and more miles than I'd like to admit to.
Yesterday, I noticed that one of the vacuum lines was coming dangerously close to hitting the serpentine belt on the front of the engine. The clamp that normally holds the vacuum line in place rusted away a decade ago, so I decided to use some velcro ties to attach the line to the positive battery cable. I didn't twist or pull on the cable in any way and the vacuum line isn't applying any force to the cable.
I get in the truck a few hours later, hit the key and I get >click<, but nothing out of the starter. One click when the key is in the start position, nothing more (as opposed to click-click-click).
Not thinking about my repair earlier, I went down to Autozone and had them test the battery - 12.8V and 550CCA, no problem there.
So then, I thought well since the click is coming from the starter relay, maybe that's where the problem is. I read on another forum that sometimes the starter relay can be resurrected temporarily by hitting it with a hammer. Which I did. And it did work! Now the truck is starting up normally every time, but I'd like to replace whatever was bad.
My questions :
1. Did I prove anything by hitting the starter relay with a hammer and then starting the truck?
2. Should I still be looking at the battery cables?
3. Should I stop hitting random parts with a hammer and take this truck down to a real mechanic before I do serious damage?
Ford Ranger / B-Series :: 2003 - Replacement Of Outside Mirror Glass?
Is it possible to replace just the glass on the outside mirrors on a 2003 Ranger?
If so, how is it done?
Ford F-150 - 1997-2003 :: Squeaky Serpentine Belt Once It Warms Up
I have a 2003 f150 4.2 v8. and i have a squeaky belt I am almost positive its the belt i went to change it today but being sick,cold (NY), getting dark having just worked 10 hrs and changing oil it was not going well.
The reason I think its the belt it does not squeak when its really cold out but once it warms up a little its back so I am thinking when it gets warm it stretches out a little and when its cold it shrinks up or am I just crazy..
Ford 7.3L Power Stroke (1999-2003) :: Serpentine Belt Coming Off AC
Leaving on a 200 mile trip in the morning and when checking the fluids, I found the serpentine belt trying to get off the AC pulley. I've put in on twice and it immediately jumps half way off when starting the engine. How long it's been doing this. Nothing is obviously loose or moved. What is likely causing this?
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: Serpentine Belt Started Shredding
About 2 weeks ago i noticed that the serpentine belt started shredding. I noticed it before it was all gone, so i parked it and started ordering parts before i did anything. Since i had to get the radiator hose off, i decided to flush the coolant, change the thermostat and the upper radiator hose to go around the belt. Once the parts arrived, I drained the coolant and did two flushes and tried to change the hoses and thermostat. the Gates hose ended up not being the right hose, in hindsight I should have used the old hose and put it back together.
But I returned the Gates hose and ordered a Motorcraft hose. not thinking, i left the system dry and possibly sitting with water from the previous flush. Three days ago, I got the correct Motorcraft part and did the work on Sunday. since it had been sitting, i decided to run another flush, i noticed a squeaking sound and that the water was coming out a little browner than when i left it. So I ran another two flushes and said to hell with it and put the whole thing back together and filled it with coolant and distilled water.
This morning, the squeaking sound was louder, but temps where fine and coolant level was fine. I drove to work ( about a 10 mile drive) and when i finally stopped, i got a whiff of coolant smell. I noticed coolant behind me and when i lifted the hood, i noticed the reservoir was half empty and coolant dripping down from the center of the block. I can still hear the squeaking, I figure the water pump is on its last leg and decide i need to go home. I walk in to work and let them know I'm gonna take the day off to situate this. Before i leave, i top off the reservoir with a gallon of distilled water and head out.
After a short distance I notice that the squeaking stops, now I'm terrified that the water pump just completely failed. (I've never had one fail on me so I'm not sure what happens when it does) As i drive home, I'm watching all my gauges. none of the temperature gauges spike, everything was normal for the drive home (another 10 miles) I park it and lift the hood and the reservoir is completely full. why is reservoir completely full? why would a leak like that stop? Should i just change the water pump? I don't want to just hope for the best, i do use my excursion to haul the kids from time to time.
Ford F-150 - 1997-2003 :: Noisy Serpentine Belt - Crank Pulley Squeak?
Been trying to isolate my noisy serpentine belt. Had the belt off and spun everything, only thing I found that made any noise was the alternator. It had a nice churp like a bearing was on its way out in it. So I replaced that figuring my squeak was going to go away. No such luck. Listening to it again while it was idling, I crawled underneath. Almost seems like the churping noise is coming from the Crank Pulley. Is there a bearing on this pulley that goes bad?
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Lost Serpentine Belt - Overheated
I was cruising along yesterday and felt the steering pump go out on the highway. Nowhere to pull over and pulling a big horse trailer. Three miles later I finally get to a wide spot to dive into. I look down and the temp gauge is maxed and the oil light is on. Most of the antifreeze boils out when I got the engine shut down. I had no choice but to have a friend bring a new belt and some antifreeze to the rescue. Got it changed and filled back up. Started and drove home fine.
I've got this twisted gut feeling about the whole deal. What kind of damage did I likely do? Things to look for? Did I just kill the longevity of the motor? I've been trying to do things right and treat it well to ensure a reliable truck.
On a side note the belt came apart in ribbons and it was absolutely shredded. The belt appeared to be less than 3 months old. No cracks or tears and a bright white numbers sticker on the back
Ford Super Duty (1999-2016) :: 2006 - Serpentine Belt - How To Route The Belt Around Tensioner Pulley
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
Ford 7.3L Power Stroke (1999-2003) :: Chirping Sound Coming From Serpentine Belt And Pulley Area
I have 1997 F250 LD since i bough it has been doing this chirping sound coming from the serpentine belt and the pulley area but when the truck has been working for 15 - 20 min it goes away
This is apart from the from the problem before I think the fan clutch is broken because when I start the truck I can hear the fan going at the same speed of the engine is that normal ? even when the truck is cold
Ford 7.3L Power Stroke (1999-2003) :: Serpentine Belt Started Squealing - Coolant Leak Behind / Below Thermostat Housing
My serp belt started squealing so I pulled the thermostat housing to inspect the rubber gasket. It looked OK, but I cleaned up both surfaces and replaced with a new gasket, and put it back together. The housing was replaced just a couple months ago along with new hoses. It was not corroded and OK to reuse.
Started the truck up and saw a slowish/steady drip of red Cat ELC dripping on the driveway. Opened the hood up again and carefully inspected around the thermostat housing - no coolant is leaking there.
I did notice the same slow/steady drip coming from just behind and beneath the thermostat housing. See in pic, this is where it is dripping. One other question, what is this plug for on the side of the water pump?
Ford - Ranger :: 1999 - Broken Timing Belt / No Start After Replacement
2.5 Litre ... Okay, I've done this on other cars, both Fords without a problem but now I'm stuck on the no start situation. I have spark and my fuel pressure is 60 psi. About to do a compression test. Only issue with replacing the belt is that no matter how many times I try removing and installing it I'm always 1/2 tooth off after rotating the engine a couple of times but that shouldn't be enough for a complete no start. Tried starting fluid. Replaced cam sensor. new plugs. checked firing order. I have spark at #1 according to my test lamp which plugs inline.
View 6 RepliesFord Ranger / B-Series :: Installing Timing Belt?
I've tried every variation of installing the timing belt on my '91 2.3L Ranger, still not in. The belt seems as if it's too short but I've been told that it "barely" fits, no kidding! I've pulled the crank balancer/timing trigger off and put it back on three or four times already. What's the trick? Everytime I get it close I'm off a tooth or more. Just frustrated, tired of hitching a ride to work.
View 14 Replies