Ford Ranger / B-Series :: 1992 - Replaced Solenoid Now No Start?
I have to fix the truck. Battery is pretty new, replaced solenoid next to battery this morning. Truck still won't start, just clicking away. Decided I needed to replace the starter, put the truck on jacks and went to the starter. At the starter solenoid there is a red cable attached, and a "loose" red wire, with a connector on the end. It would appear the connector just needs to be reconnected to the solenoid. But it won't "connect". Am I missing something? Should it not connect to the prong on the solenoid? Should I just replace the starter, and forget about the wire? I do have Chiltons for our truck, but it doesn't show a picture of the prong on the starter solenoid.
View 11 RepliesFord Ranger / B-Series :: 2003 - Engine Knock On Cold Start
Specs: 2003 Ranger Edge / 3.0 V6 / 5-speed 4WD / 238,000 miles
Yesterday my truck was in the shop for repair. Intake gasket, Transmission fluid change, all heater hoses, thermostat, serp belt and coolant flush. When I picked it up from the shop, which was after closing, I noticed a knocking on start up. From past experience on a different truck, it sounds like a cam that isn't oiling. After a few minutes the knock goes away. I drove for a few miles, turned off the engine and started it back up and no knock this time. This morning I started it, knock was back but went away after a few minutes. Oil was changed about 1500 miles ago. Running pennzoil 5/20 with a K&N filter. Up until yesterday the engine has been completely quiet. Was wonder if something may have clogged the filter or the drain back valve.
Ford Ranger / B-Series :: 2003 - Repeated Serpentine Belt Replacement
2003 3.0 ranger... This will be my 3rd time replacing serpentine belt and if needed 2nd. time for idler, tension pulleys...NOT SURE WHAT TO DO, should i replace parts again?
View 5 RepliesFord Ranger / B-Series :: 2003 - Unhooking Seat Belt Buzzer
I recently bought a 2003 Ford Ranger. What I want to do is unhook the seat belt chime. In the past with the other 3 Rangers I owned I unplugged it from under the seat. But when I unplugged this one the light for the air bag stayed on. I like the freedom to choose and I don't care for the chime.
View 14 RepliesFord Ranger / B-Series :: 2003 Turns Over But Won't Crank After Fuel Pump Replaced
Just replaced fuel pump and now it turns over but won't crank. I have checked the fuel rail. Pressure is fine. Checked coil pack I'm getting spark. Still won't crank. Checked inertia switch it wasn't tripped. What next? 2003 Ranger edge...
View 1 RepliesFord Ranger / B-Series :: 2003 - Won't Start When Warm
My 03 ranger with a 2.3 I4 does not want to restart when it is above about 80 deg outside and engine is warm. Will crank, but as soon as fuel in line runs out it stalls, like a vapor lock. After about 45 mins can push start normally( has manual trans) but have to wait about 2 hours to use starter to start.
View 11 RepliesFord Ranger / B-Series :: Replaced Front Brakes Now ABS Goes On A Lot
I had to replace the tie rods in my mazda b2300 and the mechanic also replaced the brake pads.
Now when I drive, I can hear the pump for the brake fluid going on and off when I'm not even using the brakes and the ABS goes on a lot too.
He tried resetting the computer by unplugging the battery for a bit but it's still doing it.
Ford Ranger / B-Series :: Engine Does Not Start Without Being Primed
Engine doesn't want to start without being primed once started ideals real good but still sometimes Bogs out on acceleration.
View 3 RepliesFord Ranger / B-Series :: 2003 Won't Start / Turnover Only Occasionally
Okay so the other day my ranger wouldn't start after i got off work, it would turnover only occasionally but now it wont even do that. I've tried the fule turn on/off switch underneath the passenger glove box. I unscrewed the fuel like valve cap and pressed the pin but the fuel like barely squirted out so does it mean my fuel pump is bad or what??
View 9 RepliesFord Ranger / B-Series :: Installing Timing Belt?
I've tried every variation of installing the timing belt on my '91 2.3L Ranger, still not in. The belt seems as if it's too short but I've been told that it "barely" fits, no kidding! I've pulled the crank balancer/timing trigger off and put it back on three or four times already. What's the trick? Everytime I get it close I'm off a tooth or more. Just frustrated, tired of hitching a ride to work.
View 14 RepliesFord Ranger / B-Series :: 1997 - Replaced Thermostat Still Overheating?
Bought this truck at auction a few days ago. Started drive home and noticed temp gauge almost pegged full hot. Stopped and left it and pickup up later that day with trailer. Got home and started and ran it. Will not overheat at idle. Gauge fluctuates between full cold and 1/2 at idle. Rev up and temp drops to full cold. Drive around town under 35 and it stays between 1/2 and 3/4. Get on the highway and Pegs full hot. Replace thermostat and flushed system. Lots of rusty water and chunks of rust/mud poured out.
Upper rad hose is firm and hot. Lower rad hose is warm soft. Bypassed heater core and still over heats. I can run water hose from top hole on radiator and water crosses threw radiator and pours out the bottom so I don't think it's clogged. It's not the head gasket, I have no smoke, no milky oil and no oil in coolant. Fan clutch seems fine, I can spin it with the engine off and feel resistance. Truck hasnt boiled over while running hot so the gauge may be wrong. If it means anything the truck runs very rough and pulled up a misfire on cylinder #1 and had a iac code.
Ford Ranger / B-Series :: 1994 - Engine Cranks But Won't Start
My kid is using my 94 Ranger with 215,000 miles. It quit while he was on his way to work. Engine cranks but won't start.
Fuel pressure at rail was 12 psi (Key on eng. off). I replaced fuel pump. Pressure at rail up to 20 psi. Still cranks, no start.
I replaced fuel filter. Pressure at rail up to 30 psi. Still cranks, no start.
Replaced distributor cap/rotor and plugs. I have spark at plugs.
Chiltons from 1994 doesn't list a rail fuel pressure. I see new fuel pressure regulators are set at 41 psi. I pulled mine and hooked air to it. It (FPR) cracks at 37 psi. I have lots of flow returning to tank, so I assume the fuel system is working correctly. I've never replaced the timing chain/sprockets. Distributor rotor spins during engine cranking. When I rotate the crank pulley to 0 Top Dead Center the rotor is pointing to #1 on the distributor, so I don't think the timing chain has skipped a tooth on the sprocket??????
Ford Ranger / B-Series :: 2003 - Truck Wouldn't Start Again After Parked
My 03 Ranger 4.0L has become a mystery that has baffled every one I know. Everything was fine and I ran home to something from my house was in there maybe 10 minutes came out and the truck wouldn't start. it doesn't even crank over. out of the clear blue. I had a friend who works for a garage check it and he thinks timing chain. Since then I have been told it wouldn't just fall off sitting there with no indication at all there was a problem.
Thought maybe PATS system. Its in order. Put in on a computer from auto-zone and it shows a check engine light but the reading is there is no codes in the computer on file. I am at a loss. Its been months and I really cant afford to take it to a garage right now. Its the strangest thing ever no crank, no stalling just nothing I hit the switch it lights up like its ready to start and nada.
Ford Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?
Ford Ranger / B-Series :: 2002 3.0L Sounds Like Fan Belt Squeal
After about 1 minute after starting the truck it sounds like the fan belt is squealing..(below 30 deg outside) Only its not the fan belt as I replaced it. Does not do it when it is engine is operating temperature. Have checked all of the Pulleys which seem to be all right. The frequency of the squealing sound is about 1/3 the engine RPM and will go away above 2k when it does do it. Stopping at a stop light after about 45 seconds it really starts to get loud. Can a Fan Clutch do this.. I beleive that this engine has a timing chain right?
View 8 RepliesFord Ranger / B-Series :: 1998 - Belt Started To Squeak
I have a 1998 ranger 4.0 and about a year after getting it the belt started to squeak so far if have replaced the belt, replaced the tensioner, and cleaned and wire brushed all the pulleys to remove glazing. And it still squeaks and its annoying and kinda embarrassing...
View 4 RepliesFord Ranger / B-Series :: 1996 - When To Change The Timing Belt On A 2.3L
What is the recommended interval for the timing belt change? I have a '96 B2300 with ~85K on it and he original timing belt. I wanted to change the serpentine belt and my mechanic said he'll take a look at the timing belt. It's not cracked or anything but he says that after 8 years it should be changed.
View 14 RepliesFord Ranger / B-Series :: 2000 - Window Belt Molding?
A C-note for those 2 pieces of nothing seems ridiculous. Considering sanding and painting instead.
View 2 RepliesFord Ranger / B-Series :: 1998 - Serpentine Belt Squeaking
So i have a 1998 4.0 ohv ranger and have been fighting belt squeak shortly after i got it. I've replaced the belt twice and the tensioner twice when i put a GATES belt on it stopped for like month. But its still squeaking. If i put a wrench on the tensioner and turn it the squeak stops. So i need to find a way to tighten the tensioner could i somehow jam it, our hook up a turn buckle bolt to manually tighten it, or use a different ford tensioner. I really need to do something cause this squeak is just down right annoying.
View 2 Replies