Ford 7.3L Power Stroke (1999-2003) :: Serpentine Belt Coming Off AC
Leaving on a 200 mile trip in the morning and when checking the fluids, I found the serpentine belt trying to get off the AC pulley. I've put in on twice and it immediately jumps half way off when starting the engine. How long it's been doing this. Nothing is obviously loose or moved. What is likely causing this?
View 8 RepliesFord Super Duty (1999-2016) :: 2006 - Serpentine Belt - How To Route The Belt Around Tensioner Pulley
2006 6.0l ... I've read all over for tips on routing this belt and everyone plays it off as being some simple '20-minute' task. I'm on my 4th hour on this now.
I can't figure out how to route the belt around the tensioner pulley, circled in the picture (from another thread). Everyone glosses over how to do this and I can't figure it out.
It seems like the only way to get it on is to bend the belt and slide it between the pulley and the block, but that I just can't reach the blasted thing.
Ford 7.3L Power Stroke (1999-2003) :: Serpentine Belt Started Shredding
About 2 weeks ago i noticed that the serpentine belt started shredding. I noticed it before it was all gone, so i parked it and started ordering parts before i did anything. Since i had to get the radiator hose off, i decided to flush the coolant, change the thermostat and the upper radiator hose to go around the belt. Once the parts arrived, I drained the coolant and did two flushes and tried to change the hoses and thermostat. the Gates hose ended up not being the right hose, in hindsight I should have used the old hose and put it back together.
But I returned the Gates hose and ordered a Motorcraft hose. not thinking, i left the system dry and possibly sitting with water from the previous flush. Three days ago, I got the correct Motorcraft part and did the work on Sunday. since it had been sitting, i decided to run another flush, i noticed a squeaking sound and that the water was coming out a little browner than when i left it. So I ran another two flushes and said to hell with it and put the whole thing back together and filled it with coolant and distilled water.
This morning, the squeaking sound was louder, but temps where fine and coolant level was fine. I drove to work ( about a 10 mile drive) and when i finally stopped, i got a whiff of coolant smell. I noticed coolant behind me and when i lifted the hood, i noticed the reservoir was half empty and coolant dripping down from the center of the block. I can still hear the squeaking, I figure the water pump is on its last leg and decide i need to go home. I walk in to work and let them know I'm gonna take the day off to situate this. Before i leave, i top off the reservoir with a gallon of distilled water and head out.
After a short distance I notice that the squeaking stops, now I'm terrified that the water pump just completely failed. (I've never had one fail on me so I'm not sure what happens when it does) As i drive home, I'm watching all my gauges. none of the temperature gauges spike, everything was normal for the drive home (another 10 miles) I park it and lift the hood and the reservoir is completely full. why is reservoir completely full? why would a leak like that stop? Should i just change the water pump? I don't want to just hope for the best, i do use my excursion to haul the kids from time to time.
Ford 7.3L Power Stroke (1999-2003) :: Lost Serpentine Belt - Overheated
I was cruising along yesterday and felt the steering pump go out on the highway. Nowhere to pull over and pulling a big horse trailer. Three miles later I finally get to a wide spot to dive into. I look down and the temp gauge is maxed and the oil light is on. Most of the antifreeze boils out when I got the engine shut down. I had no choice but to have a friend bring a new belt and some antifreeze to the rescue. Got it changed and filled back up. Started and drove home fine.
I've got this twisted gut feeling about the whole deal. What kind of damage did I likely do? Things to look for? Did I just kill the longevity of the motor? I've been trying to do things right and treat it well to ensure a reliable truck.
On a side note the belt came apart in ribbons and it was absolutely shredded. The belt appeared to be less than 3 months old. No cracks or tears and a bright white numbers sticker on the back
Ford 7.3L Power Stroke (1999-2003) :: Belt Screech Sound Coming From 38R
The last week or so I have been having a screeching belt sound driving me insane in my 2003 F-250 7.3. After further investigating I have found out it is coming from my 11 month old GTP38R bearing. It has an aftermarket billet compressor wheel in it and I sold the factory wheel when I installed the Billet wheel. Where to locate a factory Garrett GTP38R wheel? All I can find online are Billet wheels or random off brands. At this point I would even trade my Billet wheel for a factory 38R wheel.
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Whining Sound Coming From Transmission Area
So I've been getting a whining sound coming from the transmission area. I checked my transmission fluid and it's nice and pink so I checked my transfer case fluid… It came out like black watery gear oil! How bad is this? I am putting synthetic Dex/Merc back in it. It's got me a tiny bit concerned.
View 9 RepliesFord F-150 - 1997-2003 :: Noisy Serpentine Belt - Crank Pulley Squeak?
Been trying to isolate my noisy serpentine belt. Had the belt off and spun everything, only thing I found that made any noise was the alternator. It had a nice churp like a bearing was on its way out in it. So I replaced that figuring my squeak was going to go away. No such luck. Listening to it again while it was idling, I crawled underneath. Almost seems like the churping noise is coming from the Crank Pulley. Is there a bearing on this pulley that goes bad?
View 13 RepliesFord 7.3L Power Stroke (1999-2003) :: Serpentine Belt Started Squealing - Coolant Leak Behind / Below Thermostat Housing
My serp belt started squealing so I pulled the thermostat housing to inspect the rubber gasket. It looked OK, but I cleaned up both surfaces and replaced with a new gasket, and put it back together. The housing was replaced just a couple months ago along with new hoses. It was not corroded and OK to reuse.
Started the truck up and saw a slowish/steady drip of red Cat ELC dripping on the driveway. Opened the hood up again and carefully inspected around the thermostat housing - no coolant is leaking there.
I did notice the same slow/steady drip coming from just behind and beneath the thermostat housing. See in pic, this is where it is dripping. One other question, what is this plug for on the side of the water pump?
Lexus RX 2004-09 :: Chirping Noise Coming From Belt Tensioner Or Idler Pulley
So from reading around a lot, it seems like the chirping is from the belt tensioner or idler pulley. That said, I've not been able to find anything definitive. I tried to do the water bottle squirt test (from Gates' youtube video) and either I did it wrong or the chirp did not go away implying the issue is not the belt. While I was looking in, I could see the tensioner shaking some.
If my tensioner should not be moving, do I just need the pulley or the pulley and the mount?
- Pulley [URL] ....
- Pulley and mount [URL] ....
Also, if the above items will fix the chirp, which brand would be best?
2007 RX 350, 113K.
Chirping gets worse as it heats up. Seems to happen independent of ambient temperature. Purchased a year ago so unsure of the history of part changes.
Golf IV / Jetta IV :: Noise Coming From Serpentine Belt Area
There has been a noise coming from the serpentine belt area for some times now, and I thought when I get to work on the belt I will get it fixed.
Last night, I replaced the alternator with a brand new one from idpart with a clutch pulley (the original pulley was plastic). I also replaced the tensioner and serpentine belt with this kit from ECS: [URL] .....
Everything was put back tight and nicely. Turned on the engine: the noise is still there.
For sure there is one pulley on its way out, but with one?
Video here: [URL] .....
Noticeable @ 0:47
It's a 2.0 AVH Jetta.
Camry :: 2005 - Rattle Coming From Serpentine Belt Area
Got a nice rattle coming from the serpentine belt area of the camry, before I order some parts, I'm thinking the bearing in the tensioner is done, I just don't want to swap it out only to find out its my water pump barking or alternator bearing/bushing. doesn't seem to be emanating from the alternator.
Here's the short video : [URL] ....
Golf V R32 :: Low Grinding Noise Coming From Area Of Serpentine Belt
So, when I was leaving work I started my car up and heard what sounds like a low grinding noise coming from the area where the serpentine belt is. Let the car idle and it remained.
Put the car in gear and drove off and the sound was still there. the sound gets louder as I increase my speed. It went away a couple of times when I was braking, then came back.
I stopped at the gas station and could still hear it. After getting gas, fired the car back up and heard nothing. When I drove off, the sound returned.
I got home and put it in park, leaving the car on, opened the hood and could still hear the noise. Pressed and held the gas a few times and the sound did get louder.
I am pretty sure it is coming from some rotating part, but no clue what part. What this could be?
recap:
-get noise on startup
-while driving noise gets louder
-sometimes it stops when braking
-sound coming from area of serpentine belt
Lexus ES 2007-12 :: 2008 - Chirping Sound From Belt Area
2008 lexus es350 -- chirping noise from serpentine belt area. Chirping starts after a bit of driving. Got belt replaced, mechanic says it is water pump (as he says he saw marking and could be a prior leak), but I don't want to do this trial and error.
I got belt replaced by the mechanic who said wold fix the problem but did not. Should I replace water pump as it is expense on es350 and only to have chirping noise not fixed as it could be something else like alignment or idler pulley etc.
Ford Aerostar :: Serpentine Belt Chirping When Wet Or Cold
I have a concern with my serpentine belt chirping when it's wet or cold. I have tried soap, and other attempts to quiet it down. Belt tension is good, new water pump and fan. Otherwise no other issues so far.
View 9 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Slight Popping Sound Coming From The Top Coil Area
I blocked off the hpop discharge tube to test for leaks, shop air. I am plugged into the oil rail drivers side, and keep getting a slight popping sound. The first time I did this it took ten minutes to start, so I replaced the top injector seals. The second time it did this after about four minutes, so I took the oil rail to the local shop and they did the ball tube orings in the rail, now I went to put it back on and it does it almost right away.
Am I just pushing the oil out of the injectors? is this normal or should I have NO air noise period? I guess I am not sure how these injectors work, where does the oil go after it enters the top of the injector? It seems like it's coming more from the top coil area, more so perhaps than under the oil rail.
Azera TG (2006-11) :: Serpentine Belt - Crank Pulley Failure
Ever hear of a crank pulley failure? Mine did and took out the serpentine belt. I have 63,000 miles on the 07 and it was a big shock to see the pulley in two parts.
View 5 RepliesCamry :: Idler Pulley Replacement On Serpentine Belt Tensioner
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 RepliesFord 7.3L Power Stroke (1999-2003) :: A/C Leak Coming From Metal Tube Going Into Spongy Area
So after a hot drive yesterday we thought to do some googling about our clutch cycling on and off so fast. Yep, the airgap was out of spec. Fixed that.
Then we added some refrigerant to the truck. The truck is "new to us" and this is our first summer with it so not sure what might've gone on previously with the AC. Didn't take long to find a rather sizable leak. :P
See that metal tube going into the "spongy" area? Yeah, that's where it seems to be coming out. That tube is the only one that's cold, the rest are ambient temp. We fix a lot on our jeeps, but the AC system is naturally a bit out of our wheel house since it's not something you normally tangle with. Is this an easy fix? Or do we need to take it in to get serviced?
Lexus RX 2004-09 :: 07 - Serpentine Belt Tensioner Pulley Making Noise
My tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 Replies