Ford Ranger / B-Series :: Uneven Tire Wear / Over Inflation
I have a 1999 Ford Ranger XLT using the Futura GLS 225/70/R15 tires. The vehicle decal in the driver side door listed the recommended tire pressure to be 30 PSI. I have tried to maintain religiously along with proper balance and alignment. However, I've always had the experience of the tires wearing out more along the middle which seemed to indicate over inflation. The sections on either side of the center line seemed to wear out normally. For this reason I've had to turn in the tire prematurely as they become unsafe. These tires were made by Coopers Tire and distributed by Pep Boys. Have i been using poor quality tires all along? Do I need to lower my tire pressure below the 30 PSI recommended? If I do that wouldn't I be risking overheating and/or affecting my gas mileage?
View 13 RepliesFord Ranger / B-Series :: 2002 4X4 - Loud Bang / Pop Comes From Driver Side Front Tire
Bought a 2002 ranger with a four liter in it. Didn't notice until actually going off-road there is something wrong with the four wheel drive. In 4 high it will drive good for a random distance then a loud bang, pop, comes from what feels like it's the driver front tire. The faster you're moving the worse it is. It's not consistent at all.
Replaced the transfer case shift motor and both CV axles. Still does it. Walked next to the truck while it's moving and the front tires look like something is in a bind and it's causing the bang. Beating my head against the wall at this point.
On a side note it has something wrong with the tranny. Taking off it feels like someone bumped the rear, and after about twenty minutes of driving od light starts blinking and it shifts hard from first to second. Kill it, cures that specific problem just not the takeoff problem. Not sure if this is all related. Pulled the pan and refilled with as much fluid as came out. Which was a dark red. Still having same issues.
Ford Ranger / B-Series :: Uneven Front Brake Wear / Caliper Sticking Slightly
2000 Ranger, see my sig.
Just had to swap out the pads on my truck yesterday. The pedal was pretty mushy and I was getting shaking in the steering wheel when the brakes got warm. Shaking wasn't all the time, only after they had been used quite a bit - say after city use and the brakes had to be applied suddenly. So I popped off the tires and swapped out the pads and replaced the brake fluid - flushed it.
On the driver side front, the pads barely had any real wear and the anti-rattle clip was all messed up. It was installed properly, but it looked like the pads had smashed into it. The rotor appeared to be warped, or at least out of round - but just barely. You could see it wobble slightly in one spot if you spun the hub with the caliper removed. The caliper itself was sticking slightly.
I didn't see any evidence of damage, the brakes flushed just fine although the fluid was incredibly dirty (because I haven't done it in a long while). On the passenger side front, the pads were worn down to the level I would have expected given the mileage. The wear was even.
My question ultimately is this - is the out of round hub the culprit here? Might there be something else going on like a caliper problem? Ultimately I plan on having the rotors surfaced - one of them certainly needs it and with new pads I might as well do it anyway.
Ford Ranger / B-Series :: 1998 - Front Brake Lines Kink In Sharp Turns And Wear Out
98 Ranger Front brake lines Too short! they kink in sharp turns and wear out then start to seep then eventually leak and need replacement. Checked parts references and the lines have been considered stock. Not sure if I have a 1/2 year model.
View 1 RepliesFord Ranger / B-Series :: 1999 - Front End Started Squeaking?
I have a 99 ranger with 170000 miles and the front end recently started squeaking. its coming from the driver side but I can't pinpoint it.
View 5 RepliesFord Ranger / B-Series :: 1999 - Squeaking Front Wheel Bearings
4x4 1999 Ranger ... They are a squeaking and driving me crazy. How hard are they to do, do they need a press or can they be done at home?
View 7 RepliesFord Ranger / B-Series :: 1998 B2500 - Squeaking Front End At Slow Speeds
I have had my 1998 Mazda B2500 truck since 2000 and this problem comes and goes (it's mostly been gone lately). Usually when it is cold outside. At slow speeds it creaks and squeaks - kinda embarrassing - if I am sitting still it squeaks when I turn the steering wheel. Once the speed picks up you can't hear it. I have noticed this in other fords about the same year.
View 1 RepliesFord Ranger / B-Series :: Faint Rotating Squeaking Noise Coming From The Front Of Engine
I'm hearing a sort of faint rotating squeaking noise coming from the front of the engine; I can only assume that it's something with the belts. Nothing too pronounce cause I just notice it yesterday, anyway I was hoping I get another take on what this might be before I take it to the mechanic tomorrow.
View 12 RepliesFord Excursion :: 2001 - Front Tire Wear On Both Outer Edges
I have am 01 6.8 two wheel Limited. about 150K. My question is about both the front tires having more wear on both the inner and outer edges. The inner is a bit more but not by much.
I have been keeping very close track of my air pressure because I know the usual suspect is low air pressure but I am running 75psi and the max sidewall reads 80psi. I have never had it below 72psi. The truck tracks and steers down the road very nice with no drift or pull to either side. wheel balance is good.
Front end align is good. I have no issues with how she drives down the road. Everything seems to be checking out to be in spec..?
Ford F-150 (2009-2014) :: Front Tire Wear And Loud Creaking Sound
2014 FX4 F. Got 6000 miles on the truck, front tires are wearing on the outside edge, and also when turning the wheels to the max in either direction I get a loud creaking sound,??
View 14 RepliesFord Escape / Hybrid :: 2012 XLT Front End - Inside Tire Wear And Suspension Pop Over Bumps
I realize that is vague. I realize it could be anything from a wheel bearing to a ball joint, tie rod, control arm/control arm bushing, etc.
Are there any very common front-end steering or suspension issues on 2012 escapes? When tires are inflated to 32-34psi, the car tracks straight, gets great mileage --but almost sounds/feels like it's got a CV or wheel bearing issue on the front right. Every time I hit the brakes while backing out of the driveway I can hear a slight bump or pop. When the car is parked (flat, tires straight) there is slight play left-to-right in the steering wheel.
I'm a German car guy. Have never touched this car. (Wife's car) Right tire is wearing bad on inside. Looking for some direction so I can assess. Car has 88k miles. This will be a DIY fix. Don't have any manuals or anything so just looking for a heads up where to start. Also is Haynes the best way to go? Is there a Bentley? Anything online/CD/DVD?
Play in steering wheel makes me think tie rod (fine because easy/cheap) but such excessive wear on the inside right front makes me think wheel bearing. Could it be both? This is AWD. Is this (like a Subaru) a CV joint where the front spindle passes through a strut base that everything attaches to --so there's an inner and outer wheel bearing?
Does anything up front require a press or can it all be done without a press?
Golf V R32 :: Excessive Tire Wear On The Front
Having issues with excessive front tire wear? I have had the alignment checked by two VW garages and a third party garage and all of them confirm that the alignment is good.
The VW garage also confirmed that as far as they can see there is no suspension issues, but the excessive wear on the front tires indicates that something is wrong.
I have owned the car since new in 2008 so know it has a clean history no accidents.
Both front tires look like this.....
Passat (B5) :: Front Passenger Tire Is Getting Some Inner Wear On It
I notice that my front passenger tire is getting some inner wear on it. The tire doesn't even have 5k on it. I know I should get an alignment that's a must but is there something that might be wrong with it anyways since its just the front passenger?? Balljoint, tierod end and etc?? I don't really have a local auto shop that I trust 100% so I don't want them to be like, there is 3 balljoints out and etc. I had the inner tierods (both) and a few balljoints fixed last year and then got an alignment done. Any tips??
View 4 RepliesFord Super Duty (1999-2016) :: F250 - Wear On The Inside Of Left Front Tire
I have a 99 F-250 extended cab superduty 4 wd with the 7.3. I also plow during the winter. Recently I've noticed wear on the inside of the left front tire. Brought it to a tire shop and had them check the front end and alignment. They told me that the specs were "within" tolerances" for my truck. I'm stumped as to why the abnormal wear if everything is supposedly good with the alignment.
View 5 RepliesSanta Fe (CM - 2007-12) :: Tire Wear - Bobbling / Shuddering Front End
I just bought a used 2007 Santa Fe Limited. It has 78,000 miles on it. I have gone bumper to bumper looking for problems and am pretty happy about the condition. HOWEVER, I have noticed a shuddering/bobbling, fairly faint, when going over slightly rough roads a low speeds. The tires are shot. But they are all exactly the same ... meaning the same wear more so on the outside. I believe they were rotated properly, but something is wearing the outside prematurely. Is the shuddering/bobbling the culprit? What is the most common issue for the Shuddering/bobbling at low speeds on slightly rough roads?
Next, I want a quiet ride. Handling is not a concern. Should I go with a slightly wider tire or slightly taller tire? Lastly, I need new mats. I want them to be the same as what came with the car. Do I have to go to the dealer or are there some vendors with better deals on factory mats.
Saturn - Sl :: Right Front Tire Has Excessive Wear And Car Pulling To The Left
Right Front Tire has excessive wear on Right INSIDE and car was pulling to the left. I rotated (or is it revolved?) my tires, and now the pulling has stopped......
OPINION: Bad tire that just wore poorly? Slight alignment issue that caused tire wear that then caused car pull? Wheel bearing issue causing tire wear? Or something else?
Lexus GS 2013+ :: Front Right Tire Has Uneven Wear On Outer Thread
Any 1 have their tire that have uneven tire wear? Mines is Dunlop and my front right tire has uneven wear on the outer thread. All other tire don't have uneven wear. I'm getting new tire for all 4 rims and check my alignment. My gs is a f sport rwd.
View 3 RepliesFord Ranger / B-Series :: Squeaking Sound That Varied With The Throttle
I have a 2002 Ranger 4.0 4x4 Off-road. Over the weekend I started hearing a squeaking sound that varied with the throttle, so I guessed the u-joints needed work. I took it in (no garage or tools available atm), and the garage called me later in the day saying my driveshaft was unrepairable, that I needed a new one. I told them to hold off.
Now, a little research found me some sites claiming that Ford did indeed make some disposable driveshafts, with pinned u-joints, but in the F-series, not the Ranger.
Ford Ranger / B-Series :: 1993 / 3.0L V6 - Belt Squeaking Very Loudly
I have a ranger as said in title. No a/c. I noticed my belt was cracked very badly so I bought a new one. Dayco made for Ford and Mazda 3.0L V6. Looked the same length as the old one so I put it on and all was good. Then about 2 days later it started squeaking very loudly, not all the time, just 1500 rpm and higher. The hotter the motor got (not overheating just to running temp) the higher rpm it took for it to squeak. I put a stethoscope on all the pulleys/pumps and alt. It sounded the strongest on the idler.
So I replaced the idler and bearing (which the bearing was bad, but not the source of sound) it wasn't that. So I thought I'd give the belt a couple days, maybe it was too tight causing a bearing to get too tight and squeak. And the more I drove it the louder it got with less rpm needed to make it squeak. So I tried belt dressing, and still no fix. So today I put the old belt back on to see if that was the issue. Sure enough, it started up and squeaked just the same, but I tried the belt dressing on the old belt and it went silent, even at 3000 rpm. So I assume from this the new belt was a smidge too big. Right?