Ford Ranger / B-Series :: Strange Sounds At Idle?
Allright, I seem to be having these very strange sounds at idle. Mostly when I am in Drive and waiting at a red light. In Park, it isn't as bad it seems.
One sound is knocking. A kinda slow one and irregular. Not a motor knock tho. Doesn't sound like that. It also kinda clicks from under. So, those both sounds come from under or the sides of the truck.
Should I worry about this? I've had these sounds since I've got the truck. Sometimes louder than usuall.
Ford Ranger / B-Series :: 2001 - Oil Pan Gasket Sticking Out In The Front
My son and I were doing a transmission flush and while we had it on the lift, I noticed the oil pan gasket was sticking out in the front quite a ways. I assume its time for a new one. Is there anything I need to know having never dropped the pan on this truck? Is this a common issue?
View 14 RepliesFord Ranger / B-Series :: 2001 - ABS Light Is On / Front End Joints Replacement
I have a 2001 ranger 3.0 auto 2wd and the abs light is on. this is what i have done so far. I had to replace all the front end joints so i took the front sensors and ohmed them and got continuity and voltage when i ran a metal past them and the same for the rear on the diff. so i figure they are fine. the wires to the frame look ok and i the truck has no damage so i figure the wires are fine.
I checked to see if the fuses are installed after I got the fuse layout and all the fuses are there and good. So I took it to advance auto and it came back with everything bad sensors motor controller and if anything else could be bad with the abs it said it was. I told them it is impossible for all of it to be bad. so it must be the controller. No I'm thinking the controller it the box attached to the abs pump and lines at the power distribution box under the hood.
Can I just remove that box and replace it with little difficulty or will i have parts fly out all over the place if i remove that box from the pump? All the pictures i see the the abs controller don't look the same as the one i have on my abs pump.
Ford Ranger / B-Series :: 1996 Won't Start - Strange Engine Sound?
I just received this ranger and have never heard an engine sound like this before.
[URL]....
Ford Ranger / B-Series :: 1996 - Squeaky Rear Wheels
I am working on a 96 ranger 2wd the front brakes were shot or nearly so,about 1/8 in left and cracked. Changed them this morning at 5am because that is the cool of the day (104 today) everything up front works fine but the howling and nails across the chalk board from the back was still there. Took it to my freindly les schwab and they told me it needed axle seals on one side and the noise is from the gear lube on the shoes. they wanted 800 bucks to fix everything, went and bought new shoes,new seals,gear oil,and gasket for rear end cover it is an easy half hour job. As I was driving home tonight from the parts store the noise stopped so now i am worried either it was a rock stuck between the drum and backing plate or something broke. everything sounds and works fine....
View 2 RepliesFord Ranger / B-Series :: 2001 - Driver Side Front Brake Line Broken / Replacement
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 RepliesFord Ranger / B-Series :: 2001 - Clunking Noise From Front After Starting From Stop / Stuck In Mud Or Snow?
first off my truck is 2001 ford ranger 4x4 with an auto. transmission. when I'm driving around in 2wd, everything is fine...
when my 4wd high is on, and I'm starting from a deadstop my truck makes a weird "clunking" noise in the front end. If I'm stuck in mud or snow, and I give gas it keeps "clunking". where the problem comes from?
Ford F-150 (2004-2008) :: Grinding Noise Coming From Front Wheels
I have an intermittent grinding noise coming from what sounds like both front wheels, it sounds like metal on metal almost like something metal rubbing the rotor but I just put new pads on and the noise was there before as well with nothing touching the rotors but the pads. The sound will appear out of no-where at low speeds of 35 or below and will continue until I brake and slow down, just before I come to a compete stop the noise will stop with a slight clunk.
I can then drive away with no noise. I am pretty sure it is not brake related except maybe ABS somehow but was also thinking front axle or diff, also have read posts that are bearing related, but both at the same time?. It is the slight clunk before stopping that I can not figure out is related to. It is an 05 f150 xlt 5.4 super cab 4wd with 85k miles
Ford Ranger / B-Series :: 1994 - Slow Leaks And Vibrations From Multiple Wheels
'94 Ranger with aluminum wheels.
I have problems with slow leaks and vibrations from multiple wheels. Both problems have persisted through multiple tire changes over the years. The same shop has always done the tire changes and they tell me they've been balancing the wheels and cleaning the inner rims. The vibration went away after putting on my B2 wheels. Then swapping the rears back to the ranger wheels, 2 at a time, the vibration was back for both test drives (hence vibrations from multiple wheels).
The wheels are badly corroded at the rims and valve stems which leads me to believe it's the wheels themselves that are causing the leaks. I haven't heard of excessively old wheels causing vibrations though which is why I ask. I will likely be buying some craigslist or junkyard replacement wheels but wanted to "check in" first.
Golf V R32 :: Grinding Noise From Front Wheels
My R is developing a grinding noise from the front wheels. I thought changing the tires will fix this problem but it didn't. Any wheel bearings failure reports?
View 10 RepliesFord Ranger / B-Series :: 1989 - Grinding Noise When Let Off Gas
I have a 89 Ranger, 2.3, 2wd, Mazda 5 spd. Last year, 10,000 miles ago, I replaced the clutch, pressure plate, slave cyl, and pilot bearing. Today, it started making a terrible grinding sound/vibration when you let off the gas. The noise is coming from the clutch/transmission area. It is so bad that any amount of "engine braking" sounds terrible and I have to press the clutch in and the noise immediately stops. What to check for?
The only thing I can think of off the cuff is
1) bad pilot bearing,
2) low/no tranny oil. I replaced the oil and put silicone on the known leaky spots while I had the tranny out,
3) Input shaft had some "wobble" in it when I had the tranny out to replace clutch 10,000 miles ago.
This could be it but why would it start 10k miles later?
Cherokee :: Grinding / Juddering On Front Wheels When Turning
We had a terrible grinding/juddering on front wheels when turning which did disappear after driving for a few minutes most times, what the problem might be?
View 1 RepliesFord - Explorer :: 2001 - Front Wheels Seem To Stay Engaged With Front Differential
We have an 01 Sport Trac as a backup vehicle and it has the 3 position rotary switch on the dash for 4wd.
The transfer case engages and disengages but the front wheels seem to stay engaged with the front differential.
There are no manual hubs and I really don't think it should ALWAYS be engaged like that.
What is the probable issue and ALSO can manual hubs be installed on this truck?
Someone mentioned vacuum engagement? but I didn't see any vacuum hoses near the spindles. Didn't see any wires either other than ABS...
Ford Ranger / B-Series :: 2002 - Vibration And Grinding Noise?
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
Ford Ranger / B-Series :: 1999 - Grinding Noise When Let The Clutch Up Off Floor
1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?
View 10 RepliesFord Ranger / B-Series :: 1994 - Grinding Noise While Clutching Down - U Joint?
I have a 1994 ford ranger 4 cylinder manuel transmission regular cab. I am hearing a grinding noise when I push and hold my clutch down. It doesn't make any noise when my foot is off the clutch. It makes the noise off and on when i stop at a light or stop signs. I have also noticed a vibration at certain speeds around 30 and then again around 70. What is the cause of these noises? Could it be my U joint?
View 5 RepliesFord Ranger / B-Series :: Grinding / Rubbing Noise In Left Turn Only
I recently acquired a B4000(for a steal!), had it almost a month now and im starting to notice a few problems, all driveline related (I think).
1. Have a "grinding/rubbing" noise in a LEFT turn only. It is a 4x4 and I haven't turned a bolt on it yet, save for very minor stuff. Since this particular model has some costly parts, I'm trying to prevent buying unnecessary parts! I have a set of 31 x 10.50 on it, and even though there is some minor tire rub, im 90% certain this is not the case.
2. Has a somewhat "hard" shift when going into O/D(I think), doesn't do this all the time, I wonder if problem #2 and #3 are related.
3. Appears to be about 1in slack in the rear driveline, wondering if it is the rearend, and specifically the spider gears or pinion?
4. Also seems to be just a LITTLE slack in the front left CV axel, is this something I should be worried about? the front right is good and tight, Tcase shifts like its suppose to.
Ford Ranger / B-Series :: 2010 - Grinding Noise From Manual Transmission
A friend has a 2010 ranger with the 2.3L with the manual transmission. He said that when he drives and the rpms are up he said he gets a grinding noise it doesn't matter what gear 1rst or 5th. He think throw out bearing but no noises at all until the rpms are up there. I was think internal like shift fork but don't know.
View 4 RepliesFord Ranger / B-Series :: Brake Pedal Pulsates And Feels Like Something Is Grinding
I have a 2010 Ford ranger sport 4x4, manual, and when backing up at a decent speed, then press the brake to slow up then depress the clutch, the brake pedal pulsates and it feels like something is grinding. It has happened in first once, but I can make it happen in reverse anytime...
View 1 Replies