Ford Ranger / B-Series :: 1994 B2300 - Grinding When Downshift To 4th / Stuck In 1st Gear
I bought the 94 B2300 from a guy that said he got it from an auction and didn't know much bout it. Got 30 mins down the road and went to down shift to 4th coming into town and all I got was grinding. Turned it off and it would go into other gears and start in gear with the clutch pushed in. Wen I tried to take off it wouldn't move and just died. Towed it home and installed a new clutch kit in it. Got the clutch bled and went to test drive it and now it is stuck in 1st gear. Can it be easily fixed or am I going to have to replace the transmission...
View 3 RepliesFord Ranger / B-Series :: 1989 - Grinding Noise When Let Off Gas
I have a 89 Ranger, 2.3, 2wd, Mazda 5 spd. Last year, 10,000 miles ago, I replaced the clutch, pressure plate, slave cyl, and pilot bearing. Today, it started making a terrible grinding sound/vibration when you let off the gas. The noise is coming from the clutch/transmission area. It is so bad that any amount of "engine braking" sounds terrible and I have to press the clutch in and the noise immediately stops. What to check for?
The only thing I can think of off the cuff is
1) bad pilot bearing,
2) low/no tranny oil. I replaced the oil and put silicone on the known leaky spots while I had the tranny out,
3) Input shaft had some "wobble" in it when I had the tranny out to replace clutch 10,000 miles ago.
This could be it but why would it start 10k miles later?
Ford Ranger / B-Series :: 1994 - Truck Won't Turn Over Just Making Noise Like It Wants To Start
The truck just won't turn over makes a rrrgh rrrgh noice like it wants to start, I push the gas peddle to the floor and I should smell a lot of gas but don't!!! I added oil when it died at the store last night and it started up but the oil stick indicates oil is fine??? Pulled the diode out this morning put it back in the truck would not start just made that noise but turned it off and reseated the diode and it started??? These things may or may not have anything to do with the problem. Could it be electrical or oil pressure gauge sticking or something else that I could tell my mechanic and he could fix so I don't get stuck????
View 14 RepliesFord Ranger / B-Series :: 2002 - Vibration And Grinding Noise?
Bought a 02 Ranger, 4.0 4x4 super cab 122,000 miles. etc Picked it up for 500 bucks because someone scrapped it along the side of a guardrail this last winter. Replaced rack and Pinion (cracked), Tie rods, Shocks, driver side knuckle and wheel bearing, and some body issues (bed is still shot so if any black short bed sitting around let me know). I've been kind of putting around all day in it, letting it used to working again. Starts right up, turns easily, I string aligned it so it goes where I want.
But as I get up to speed start at about 10MPG there is a vibration based noise coming from the front, can't pin down if its left or right. If Im going straight then turn it gets slightly more intense as I even start turning the steering wheel. The noise increases with vehicle speed. And I don't know if its separate or related, but any turn over 5-10* to the left results in a grinding sound but then I turn to about 10-15 and it gets less intense. No noise turning right.
I'm thinking a bad CV, TWO bad CVs, or a bad differential. Before I start ripping into those things, thought I'd get opinions, or hopefully experience in this area. I'm really hoping its something small and stupid. (like not getting a professional alignment)
Ford Ranger / B-Series :: 1999 - Grinding Noise When Let The Clutch Up Off Floor
1999 ranger 3.0, 5 speed stick. I was backing out of my driveway but there was a car coming so i pushed in the clutch and waited for the car to pass, when I let clutch pedal up off floor i heard a grinding noise, a little while latter did the same thing in first. Is this a first and reverse gear scyronizer or something else. What causes this and how to fix it ?
View 10 RepliesFord Ranger / B-Series :: Grinding / Rubbing Noise In Left Turn Only
I recently acquired a B4000(for a steal!), had it almost a month now and im starting to notice a few problems, all driveline related (I think).
1. Have a "grinding/rubbing" noise in a LEFT turn only. It is a 4x4 and I haven't turned a bolt on it yet, save for very minor stuff. Since this particular model has some costly parts, I'm trying to prevent buying unnecessary parts! I have a set of 31 x 10.50 on it, and even though there is some minor tire rub, im 90% certain this is not the case.
2. Has a somewhat "hard" shift when going into O/D(I think), doesn't do this all the time, I wonder if problem #2 and #3 are related.
3. Appears to be about 1in slack in the rear driveline, wondering if it is the rearend, and specifically the spider gears or pinion?
4. Also seems to be just a LITTLE slack in the front left CV axel, is this something I should be worried about? the front right is good and tight, Tcase shifts like its suppose to.
Ford Ranger / B-Series :: 2010 - Grinding Noise From Manual Transmission
A friend has a 2010 ranger with the 2.3L with the manual transmission. He said that when he drives and the rpms are up he said he gets a grinding noise it doesn't matter what gear 1rst or 5th. He think throw out bearing but no noises at all until the rpms are up there. I was think internal like shift fork but don't know.
View 4 RepliesFord Ranger / B-Series :: 2000 - Grinding Noise Only When Turn Left And At Any Speed
When I make a left turn I have a horrible grinding noise. Only when I turn left and at any speed.
View 2 RepliesFord Ranger / B-Series :: 2003 - Grinding Noise While Shifting - Use Pressure Bleeder On Clutch System?
Just picked up a 2003 Ranger XL 2.3L and notice that I get a little grinding every now and then when shifting into 1st gear. The clutch was replaced 3 years ago according to the PO but had no clue as to how long it's been since the clutch was bled.
I've used my Motive pressure bleeder numerous times in the past on brakes with much success but I've never used it on the clutch. I've used vacuum bleeders as well but it's always a 50/50 success rate with that. The pressure bleeder just works much better for me.
Using a pressure bleeder on a clutch and if so any tips like still needing to tip the master cylinder end up to release any potentially trapped air bubbles?
Ford Ranger / B-Series :: 1994 - Jerking Below 3k RPM?
My 94 ranger, 3.0 v6 began to sputter and jerk about a month ago. It does this when ever give more then lite throttle up until about 3000 rpm. I have replaced plugs, wires, coil and cleaned the air flow sensor. I feel like this has worked a little but the problem is still definitely present. When I hit 3k rpm if feels lie the truck begins to run correctly and almost like it had a power ban much like a dirtbike, but again it's just the truck running correct.. And above 3k rpm it runs great... and every so often the problem will completely disappear for 5 minutes or so, then come right back.
View 1 RepliesFord Ranger / B-Series :: 1994 - Mpg Dropped - Fix?
I have a 94 2wd 4.0 auto 3.08 rear end it has 195,000 im gettin 15 city 18 hwy I used to pull 24+ hwy I changed plugs and wires no change? It has the 4.0 tick but its always had it....
View 7 RepliesFord Ranger / B-Series :: 1994 - Got Codes 218 And 998?
Working on a friends 94 ranger, 2.3 L with codes 218 and 998. Chiltons manual does not even show this code. Code is for Loss of Ignition Diagnostic Monitor (IDM)/left side. What exactly is this? Can't find anything that explains the IDM.
998 means a hard fault.
Ford Ranger / B-Series :: 1994 - Low To No Heat
1994 ranger 3.0 .. New: water pump, htr. hoses, radiator, thermostat, pulled & flushed htr. core. (2 year time frame) ....
View 5 RepliesFord Ranger / B-Series :: 1994 - Won't Start After Warm Up?
I have a 1994 Ford Ranger 4.0L 4x4, 130,000. I love this truck but about a year ago it started not starting after it warmed up short distances in the summertime? It start right up on cold crank...Runs smooth idles like a champ...but if i shut it off..wont start for 20 to 40 min??? It doesn't happen in the winter months??? So I changed the fuel pump, filter, relays. I feel like it has something to do with the Ignition Control Module. Would that come up in a code?
View 13 RepliesFord Ranger / B-Series :: 1994 - Hesitates Under Acceleration
Having a slight issue with my ranger. So I bought this truck out of a junkyard about a month ago, its a 94 4x4 with a 4.0 and a five speed. When I bought the truck the motor was blown so a few weeks ago i replaced it with a 4.0 from an aerostar van I had laying around. Right after I changed it the truck was running good with no issues, until a few days ago going to work the truck started hesitating going up a hill. Now the truck does it all the time, sitting at idle the truck runs smooth as silk, at half throttle it does it the worst but when you mash the peddle to the floor it clears up and runs good.
So far I've replaced the plugs, wires, coil pack, mass air sensor, throttle position sensor, and the fuel pressure regulator to try and fix it but nothing has worked. I've checked the fuel pressure it has 30 at idle and 40 with the vacuum hose pulled off of the regulator, I even taped the gauge to the windshield and went for a ride and there was no drop in pressure when it started acting up. a few other things i have done were plugged all the vacuum ports to rule out a leak, reset the computer and checked for codes. the only code that came up was 522. So I think my next step is going to be buy new oxygen sensors ? But my question is wouldn't the check engine light come on if it was an oxygen sensor ?
Ford Ranger / B-Series :: 1994 - Battery Keeps Running Down
Got a problem with the '94 Ranger. Something keeps draining the battery. For reference, the truck is an XL, manual 4x4, 4.0L, 5-speed. I've been trying to keep driving it so I could try and diagnose the issue. At first, as long as I cranked it every day, it stayed charged up, but now it has gotten worse. It will run down in an hour or two. I know figuring this kind of problem out is tough, but I thought maybe some others of you may have experience in this area that might benefit me.
Based on a gut feeling, my first idea was that there was something going on inside the AC compressor. So, I disconnected the compressor, but that wasn't it. My plan at the moment is to replace the wiring harness between the battery and the starter. The current harness is pieced together (not my doing), and whether it fixes this problem or not, it needs to be done. Another thing I've thought about is the ignition switch. It acts "funny" to me, but it has never really given any trouble.
My son needs to take this vehicle back to college with him in a couple weeks, and I need to get it figured out.
Ford Ranger / B-Series :: 1994 4.0 Sometimes Will Crank And Not Start
94 Ranger, 4.0, Automatic, 280k miles. Normally starts and always runs fine. Sometimes will crank and not start. Fuel pump replaced Feb. 2015 and again Dec. 2016. Have had it towed 3 times. Always starts when it gets to the mechanic. Sort of reminds me of vapor lock on the old cars with carbs, because if it sits long enough after not starting, it will start, no problem. Never died out or even coughed when running and plenty of power. When I take off the gas cap, it sucks in air like a whale. Twice I did that and it will not start right away, but if it sits for an hour or so, it starts no problem. Just bought a new gas cap 10 minutes ago and looked in a Haynes manual and a " gas tank vapor valve assembly" is mentioned. I don't want to change parts just to see what happens. Mechanics say there are no codes shown.
View 1 RepliesFord Ranger / B-Series :: 1994 - Headlights On At All Time / Won't Come Off
The headlights on my ford ranger 1994 won't come off. All fuses are good and wondering the next step?
View 9 RepliesFord Ranger / B-Series :: 1994 - Only Goes In Reverse When Warm?
I have a 1994 Ford Ranger XLT xcab with a 4.0 engine.It will take off and drive in the freezing cold but when it warms up it will only go in reverse.Once in awhile it will go into drive.What seems to be the problem. I had also backed up over a railroad tie in an icy parking lot but still drove away.
View 3 Replies