Ford Ranger / B-Series :: 2000 XLT - Transmission Slips When Starting From A Stop
2000 Ranger XLT 4x4 3.0L Auto
So a couple months ago I had a transmission problem. It shifts high and hard all times and after the "od" light gets going (after it gets warm), the transmission slips (like riding clutch) when starting from a stop. If I went from drive to 1st gear with the selector and back, it cleared the slipping problem for a bit. I did an oil/filter change and about 50 miles later the truck is running fine, no issues. One day I hopped in it to go to work and it was like nothing ever happened. Fast forward 1,500 miles later. I start to notice the transmission is subtly shifting weird, like a small jerk when shifting. It gets worse over 50 miles and now I am back to the above problem. Is there a way this could be a sensor or solenoid problem? I never heard of a transmission correcting an issue then starting at it again so much later.
I don't like fixing or working on an issue unless I am at least 95% sure what the problem is. I also don't have $2k to plop down on a repair at the moment. Would it be worth it to take this to a dealership and see what trouble codes I am getting? I would try a transmission shop but it's not guaranteed they will have the test equipment to check a ford transmission. Also a friend said that AutoZone and other stores can't check transmission codes. So what's the best option here?
Ford Ranger / B-Series :: 1987 - Rough Idle And Stumble When Starting Out From A Stop
1987 Ranger and the computer will not communicate. I'm trying to check for codes because of a rough idle and stumble when starting out from a stop. Check engine works but won't flash when using a jumper across the data link. Used a OTC scanner but it only times out and comes up "no data". Where to go from here?
View 7 RepliesFord Ranger / B-Series :: Starting From A Stop In 1st - Truck Bogs Down When Letting Out The Clutch
Started up my truck today, accel pedal didn't want to move, after giving it some more force it eventually became "unstuck". Now, the real issue I'm having is from a dead stop, in 1st gear, as I'm letting out the clutch the truck boggs down as if I'm not trying to accelerate. I'm giving it as much as I normally would as I'm letting out the clutch but the motor will either die or take a couple seconds before it starts to go. Once I'm moving I don't notice any problems clutching through gears. The check engine light IS on now, however I don't have any diagnostic gear or really any tools for that matter. 1998 2.4L 5-speed...
View 2 RepliesFord Ranger / B-Series :: 2007 FX4 - Clunking Sound From Front End In 4 Wheel Drive
There is a clunking sound and feel from the front end of my 2007 Ranger FX4 when in 4 wheel drive. This happens sometimes but not always on engaging or disengaging 4 wheel drive, as well as sporadically while driving along. I took it back to Ford on warranty with this problem last year, and after a few attempts I had them admit that something was wrong and they finally diagnosed that it was the front drive shaft that was binding where it leaves the transfer case, this was replaced. I have now put maybe 50km (max) on in 4 wheel drive and the problem is back, I don't think the problem was ever fixed.
View 14 RepliesFord Ranger / B-Series :: 2003 - Clunk When Driving In The Snow
I've been dealing with this for 2 years now and its going to snap my axle shaft one of these days. I am scared to take it out in a snow storm because the truck will clunk and then release. Its a split second thing but its enough to notice and make me worry a lot. I cant figure out why and ive done the plugs and wires but that didn't solve the problem. It only happens when its snowing or when I drive though a gust of wind that has stired up some snow. I know it must be something electrical because it only happens when there its cold and wet and not all the time. In the rain it does not matter but when it snows i just wont go out at all. The truck is a 2003 4.0 4x4 with a manual. Not a function of the 4 wheel drive it happened in 2wd as well.
View 14 RepliesFord Ranger / B-Series :: 2001 - Trans Judder When Coming To A Stop Moving At Around 3 - 4 MPH
2001 4.0 4x4 auto trans... Problem, tranny judders when coming to a stop moving at around 3-4mph. Engine drops to around 500rpm and maybe one second later returns to normal as the tranny seems to disengage. No judder or shifting problem when accelerating.
View 5 RepliesFord Ranger / B-Series :: 2001 - Clutch Pedal Rubber Stop Part Number?
I'm looking for a part number for the rubber stop that mounts behind the clutch pedal on the firewall for a 2001 Ford Ranger 4cyl 2.3L 5spd Manual. Can't seem to find it on the web. It looks like it snaps/presses into a mounting hole behind the pedal. The original one decided to disintegrate and now I get a nice knocking noise when ever the pedal is depressed.
View 7 RepliesFord Ranger / B-Series :: 2001 - Oil Pan Gasket Sticking Out In The Front
My son and I were doing a transmission flush and while we had it on the lift, I noticed the oil pan gasket was sticking out in the front quite a ways. I assume its time for a new one. Is there anything I need to know having never dropped the pan on this truck? Is this a common issue?
View 14 RepliesFord - Mountaineer :: 2001 AWD - Front Clunking Noise
I have a 2001 AWD Mountaineer with 5.0 engine and 183,000 miles. A little over a year ago a harsh clunking noise started coming from the front. It was obvious that it was coming from one of the drive component because the noise and harshness changed with speed. At slow speeds it was clunking with every revolution of the wheels. The intensity seemed to change with the direction of the wheels also. I figured it might be a CV joint and proceeded to check them out. None appeared to be bad, but with the mileage on the car I figured it wouldn't hurt to replace the axle shafts, so I started with the left (driver's) side which is where I felt the noise was coming from. The noise went away and I was happy. To my surprise about 6 months ago the same noise came back. This time I replaced the right side axle shaft. Again the noise went away.
Unfortunately the problem hasn't gone away though. A couple of days or a couple of weeks may pass with no problem, but then suddenly it starts again. I took it to a trusted mechanic when it was making the noise. It was so loud when I pulled into his driveway that he stopped what he was doing to look. But, when he took it for a drive it was as quiet as the day I bought it in 2001. I also talked to the service people at the local Ford dealer and they told me that there was basically nothing they were aware of that could cause this problem, but to bring it in the next time it did it and they would check it out. At this point I almost want something to fall out of it. At least then we'll know where the problem is.
Ford Ranger / B-Series :: 2001 - Strange Grinding In Front Wheels
I have an 01 Ranger 4x4 with 113,000 and have had it for around 2 years. After I bought it I noticed a grinding sound that appeared to come from the front wheels during braking. On my old 97 Ranger I noticed the same sound and had to replace both rotors because the pads had worn to the rivets! So I pulled the front wheels and found I had about 1/2 inch of pad left and the rotors were shiny on both sides. I recently checked them again and a little less pad but the rotors are still shiny. The pads haven't worn far enough to get to the squealer bars yet.
The sound is like the metal on metal sound some have described during all phases of driving but this only occurs intermittently while braking. It doesn't matter if its light braking or heavy it sounds the same when it does it. I do think I may have a warped rotor on at least one side as the truck shakes some when I apply the brakes, especially at higher speed. I have not checked my front bearings visually but there doesn't appear to be much play if any doing a wheel shake test. What it could be and could it be related to a warped rotor?
Ford Ranger / B-Series :: 2001 - ABS Light Is On / Front End Joints Replacement
I have a 2001 ranger 3.0 auto 2wd and the abs light is on. this is what i have done so far. I had to replace all the front end joints so i took the front sensors and ohmed them and got continuity and voltage when i ran a metal past them and the same for the rear on the diff. so i figure they are fine. the wires to the frame look ok and i the truck has no damage so i figure the wires are fine.
I checked to see if the fuses are installed after I got the fuse layout and all the fuses are there and good. So I took it to advance auto and it came back with everything bad sensors motor controller and if anything else could be bad with the abs it said it was. I told them it is impossible for all of it to be bad. so it must be the controller. No I'm thinking the controller it the box attached to the abs pump and lines at the power distribution box under the hood.
Can I just remove that box and replace it with little difficulty or will i have parts fly out all over the place if i remove that box from the pump? All the pictures i see the the abs controller don't look the same as the one i have on my abs pump.
Passat (B5) :: 2001 - Clunking Noise Only On Accelerating From A Stop?
Gf's 01 B5 Wagon(tip) has the clunking noise only on accelerating from a stop,does not do it any other time,does it in tip mode as well,tie rod ends,rotors and front brakes were replaced about 2 months ago,could this be a ball joint/control arm issue,I read as much on this in the other threads when I searched,no noise on turning or braking,possible mount issue?
View 2 RepliesFord - Ranger :: 1998 - Heavy Clunking Sound While Starting And Stopping
I have a 1998 Ford Ranger, 3.0 4X4. Purchased in early 2002 with a clunking problem which has not gotten worse or better. When I take off it is a heavy double 'clunking' like something shifting and the settling. I have had 4 mechanics look at it, have changed the front u joint and have had the motor and transmission mounts checked but the mounts are OK. Can't figure this out. I talked to a person at a local car parts store and he mentioned that it could involve the 'yoke' and that it just might need to be greased but he was just guessing.
View 9 RepliesFord Ranger / B-Series :: 2001 - Driver Side Front Brake Line Broken / Replacement
My front driver side brake line broke. It had a typical double flare fitting at the caliper but at the distribution block on the other end it had a flared fitting that would be used on a industrial hydraulic unit. I took it to the NAPA store and they told me to cut the nut off the old line and put it new line and double flare it. I did and it leaks. Do I need a special fitting on the end that goes the distribution block?
View 2 RepliesFord Ranger / B-Series :: Noise From The Front Whenever Turn The Truck Slightly To Right?
My 99 ranger has just hit 111,000 miles. I'm getting a weird sound from the front right whenever I turn the truck slightly to the right. I don't hear it if it's leaning left. Is this likely the wheel bearing? I've heard these rangers are not best known for the quality of the wheel bearings.
View 14 RepliesFord Ranger / B-Series :: 2001 - Won't Heat Clicking Noise?
i have a 2001 ranger 4x4 the problem is sometimes it will switch into 4 wheel drive and sometimes it wont just hear clicking noise ,i'm preety sure it doenst have a vaccum.
View 14 RepliesFord Ranger / B-Series :: 1999 - Clunking On Deceleration?
I have a 1999 ranger 4x4 with a 3.0. automatic, extra cab.
I have noticed that sometimes (this has happened twice so far) on slowing down, (just letting off the gas) it will make a large clunking popping noise like you hit a large pothole and bottomed the truck out (or if you had hit a small animal) However, both times nothing was in the road way and no damage was done to the truck. both times it has been in 2high.
The truck does not swerve, grab or anything funky other than make a loud CLUNK every now and then.
This has happened when you let off the gas at about 25mph and coast along. (it may be when you apply gentle throttle to keep rolling, but I can't remember, I was not driving the truck this time, the first time it happened was several weeks ago and I put it off as a freak happening). I will check the usual suspects, u joints, ect, but I was wondering if there could be something else happening...vperhaps something in the front diff? or transfer case? It kinda felt like it came from the front of the truck.
Ford Ranger / B-Series :: 2001 - Driver Side Power Window Motor Won't Stop After Window In Upper Position?
2001 Ranger 4 liter 4 door My driver side window goes up and the electric motor does not stop running when the window reaches its normal upper position. Instead it goes bang-bang-bang until I take my finger off of the switch. I'm guessing there is a limit switch that should disconnect the motor but has failed. The bang-bang (again I'm guessing) probably is some sort of a spring loaded torque limiter to protect the motor. Other than that, the window goes up & down as it normally should. I have no problem digging into the door, except with the window, door lock and outside mirror switches, I don't have a clue regarding how to get the inside door panel off. I know to disconnect the battery 1st.
View 1 RepliesFord Ranger / B-Series :: Rattle Noise From Front End When Hitting Any Kind Of Bump
This rattle noise occurs when hitting just about any kind of bump. Sounds like coming from driver side. It sounds like something loose like a washer rattling against something metal. I recently have replaced the radius arm bushings, front springs, and shocks. The sway bar links and bushings look and feel ok. What it ended up being? I have never heard ball joints make such a noise but it wouldn't surprise me if they were in need of replacement.
View 10 Replies