Ford Ranger / B-Series :: 2000 XLT - Cruise Control Not Working
My 2000 4.0 XLT Ranger has been without working cruise control for several months now. I've checked what appear to be likely related fuses and they're all good. I *DID* have a recent problem with my brake lights but that's been fixed. (The shop that replaced my rear leaf spring hanger brackets pinched a hot wire between the brackets and the frame which eventually shorted. Wire and fuse were replaced.)
A few years back, Ford had a recall related to the Cruise Controls causing fires. I had the recall service performed on this truck. In a nutshell: The switch to disengage cruise when braking is attached to the master brake cylinder, and a leak in the switches diaphragm allows brake fluid into the switch causing an electrical short, causing the wires to heat up, and in some cases causing a fire. Ford, instead of switching to a different switch design (like maybe a mechanical switch on the pedal?) put a fuseable link in the hot wire from the potentially leaky switch.
Well, the truck now has over 150K miles on the factory brake cylinder/cruise control switch. I'm suspecting that my switch finally leaked, shorted and blew the fuseable link. Would Ford fix it? (They should, considering the lame fix for a lame design flaw.)
Ford Ranger / B-Series :: AC Clutch / Radio / Cruise Control And Turn Signals Are Not Working
My AC clutch, radio, cruise control, and turn signals are not working. I have checked all fuses and relays that I can find, all good. From what I have read, these are not part of the GEM function. What I need to check next!
View 7 RepliesFord Ranger / B-Series :: 2007 - Cruise Control Turning Off Every Once In A While
It started with the cruise control turning off every once in a while. Then it would only stay on for 7-8 seconds, then eventually it would turn on, then shut right off. Now it won't even turn on.
When I did the diagnosis sequence (On, Resume, Coast, Set....) it blinked 3 times saying "Bad deactivation switch or circuit". So I replaced the blue switch on the brake pedal and it still doesn't engage.
It's a 4.0 liter with a manual tranny. I've been researching this a lot, and it seems in 2007 they changed up things probably because of the big recall.
I don't see any kind of deactivation switch around the master cylinder. It seems that was in use until 2006 or 2005.
I see a different kind of switch on the clutch pedal, thinking it must also have a deactivation switch. I see a long spring loaded type of switch with about 5-6 wires coming out of it, but I can't find any info on the web about that switch.
All three of my brake lights are working. It seemed to deteriorate rather quickly (Over the course of 3 days) and now it's completely dead.
Ford Ranger / B-Series :: 2002 - Cruise Control Work Intermittently?
I am normally on the super duty side but I have a 2002 ranger 3.0 auto EX cab if that matters with this issue. My cruse control will only come on rarely but when i does it works fine. Most of the time when I hit the ON button the indicator only blinks like a "relay" of some sort is not latching up. Don't know if this is an all solid state system or if there are electro mechanical relays involved as well. When it does work and I hit the brakes it will drop out completely rather than just disconnect from the controller and need to hit the ON button again, usually with no results.
View 8 RepliesFord Ranger / B-Series :: Cruise Control Stuck On And Wouldn't Release
So I'm motoring along a country road with the cruise set at 50 mph and the truck starts to increase speed.
Tap the brake - nothing happens. I'm up to 65 mph! Knock it into neutral and it revs to around 3,500 rpms and then it unsticks.
What in the world is going on with that? After thinking on it, a few miles farther on and I set the cruise again.
It began immediately picking up speed. I hit the brake and nothing happened. Then I hit the off button and nothing happened.
So again I bumped it up into neutral and it did the same thing - revved for a moment and then kicked off.
The dealership where I get my service done can't get to it for several days. So I'm checking in the meanwhile to see possibilities to identify a cause.
Ford Ranger / B-Series :: 2003 - Cruise Control Set Button Broken / Accelerator Stuck
2003 ford edge 3.0 V6 ... I was driving down interstate today going 70, set my cruise control & the button broke. My accelerator was stuck, when I would hit the brakes it would literally shake the whole truck. What happened & why?
View 3 RepliesFord Ranger / B-Series :: 2000 - Cruise Control Switch Broken / Airbag Removal
The cruise control switch on my 2000 Ranger just broke. It looks like you have to remove the airbag to access it. How is that accessed? It looks like there are 2 plugs on the back of the wheel that need to be removed.
View 9 RepliesPassat (B5) :: Cruise Control On 1998 VW 1.8T Not Working
About a year ago the cruise control in my 1998 Passat started to work intermittently. Now it is not working at all. I have tried to tap the stalk thinking that something could be loose. I have a 5 speed manual.
View 6 RepliesPassat (B5) :: 1998 - Cruise Control Not Working
I just purchased my 98 1.8t manual and for the most part it was a steal. Only 108k miles. Everything is strong just a few minor things. Right now I want to get my cruise control working. Is there a light in the dash that goes on? What are the fuses related to it? Nothing happens when I turn it on or hold the button to set it. what should I look for?
View 5 RepliesFord Ranger / B-Series :: 2007 XLT - Cruise Control Light Blinks After Push On And Resume Buttons
My cruise control has been out for awhile and I have run the diagnostic test several times, earlier this year and now again recently. The cruise control light blinks after I push the ON and RESUME buttons, but no blink for the COAST button. I suspect there is a problem in the wiring, but I wanted to get your thoughts before I replace the switches. 2007 Ranger XLT ....
View 1 RepliesJeep - Cherokee :: 1998 - Cruise Control Not Working?
I have a 98 Jeep and the cruise control is not working. The light does not come on when I hit the switch either.
I'm reading that it could be the brake switch, the on/off switch or maybe the clockspring. Is there somewhere I can get the voltages that should be at these switches or maybe the ohms for them before I go buy new ones?
I'm driving to Colorado for a week of 4 wheeling and it would be nice to have the cruise control working!
Ford Ranger / B-Series :: 1988 - Wiper Won't Roll Down To Normal Position And Not Working At Slow Setting?
1988 Bronco II 2.9L Issues:
- When I turn off the wiper switch the wipers immediately stop in place, they do not continue to their normal 'down' position.
- The switch's adjuster to slow the wipers isn't working, only the low and high settings work.
What I've done so far:
- Replaced wiper switch with used from spare parts.
- Replaced wiper switch with new from spare parts.
- Replaced wiper motor with remanufactured from Autozone.
- Thoroughly cleaned wiper motor ground terminals.
- Replaced interval wiper governor with used from spare parts.
The problem occurred after the truck sat in my garage for 6 months while I removed and reinstalled the engine to replace some gaskets & seals.
Ford Ranger / B-Series :: 1998 - Speedometer Not Working
so heres whats happening. My 98 ranger speedometer has not been working since I owned it (I am the second owner who got it from a grandpa) and I've replaced the vss sensor two times, got a new connector and gave that a try and still nothing. Yes I've looked for cracks in the wire or any exposed copper, I've looked through many forums and cant figure it out. At first before replacing the vss, my abs and check engine light weren't lit up until i put a new vss sensor on that i got from o'reillys, so then i got another one thinking it was just a bad sensor and still no luck. another thing is when its cold in the morning and i get in my pickup to go to work it will start working once i go over 30 and fluctuate between that and 20 but if i don't accelerate it will not bounce all over the place.
View 4 RepliesFord Ranger / B-Series :: 1998 - Right Side Turn Signals And Flashers Not Working
98 4wd extended cab. So weird only the right side is not working. Lights in the dash to the lights outside everything is dead.
Fuses that I could find are good. We replaced the mf switch a few months ago.
Ford Ranger / B-Series :: 1998 - High Beams And Turn Signals Not Working
The turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 RepliesFord Ranger / B-Series :: 1998 - Flashers And Turn Signals Stopped Working
I recently got a pretty cherry 98 Ranger 3.0 2wd extended cab auto. So far all it has needed was wiper blades, floor mats and a heater blend door. Last week my daughter informed me that the flashers and the turn signals stopped working. I looked for blown fuses and then took the low road and just bought a new flasher (my alldatadiy manual showed that the flasher was common to the turn signals and the hazard flashers so I took a shot at just throwing a part at it). That didn't fix it or else. Any pointers?
View 3 RepliesFord Ranger / B-Series :: 1998 - Seat Belt Light / Chime Not Working - Airbag Code 27?
I noticed the passenger side on/off switch for the airbag doesn't illuminate anymore on my 98 Ranger. Whether I turn the key on the switch to on or off it doesn't illuminate either way. The airbag light on the dash flashes showing, counting a code 27 and then it stays on. I also noticed the seat belts on symbol doesn't illuminate and in the owner's manual it says it should illuminate and chime. I remember it use to illuminate but I don't remember a chime.
Someone with a 98 that has a seat belt reminder light that illuminates and chimes until you fasten the seat belt? I don't know if that and the airbag code is related. But I want to fix both? I guess the simplest one to tackle first would be the seat belt light/chime. I don't see a fuse for it. I guess I need to know first is it really suppose to chime.
Prius (2010-12) Fuel :: ECO Vs NORMAL Vs PWR Mode When Using Cruise Control
We have 2 trips coming up this summer (600 miles and 1400 miles), these will be my first long distance with the Prius.
Did anyone tested fuel economy using the cruise control in ECO vs NORMAL vs PWR ?
Ford Ranger / B-Series :: 2001 - At Normal Temp RPM Drops To 0 While Shifting From D / R Into P - MAF Sensor?
My 2001 Ranger V6 with 160.000 miles runs like a Swiss watch. After warming up slightly it idles at the typical 750 RPM. I can pull out of the garage, park in the yard, shift from D or R into P and the idle holds at 750 RPM until I turn the engine off.
But, If I've driven to warm the engine to normal run temp and go through the same D or R and into P, the RPM drops to nearly Zero and sometimes the engine stops.
This has happened in the past so I take out the MAF, squirt it good with MAF cleaner, put it back in and everything is hunky-doory. But not this time. What am I missing??